JAR SYSTEM REBSCL32 USB-C Charging Retrofit

Specifications :

• Product Name: Quick-Sense USB-C Charging Retrofit for Spectrum Cloud32 Cart
• Model: REBSCL32
• Designed in: USA
• Made in: China

Product Usage Instructions

Installation Instructions

1. Install the top L brackets using 3 M5 screws and nuts on each. Secure them to the lowest vent in the side of the body of the cart with the screw on the outside and the nut on the inside.
2. Position the bottom Z brackets with the open ridge end towards the back of the cart. Clip in the bracket to the wall. Connect the power cable. Connect the other end of the power cable to one of the charging hubs and set the hub on the top brackets.

Quick Start:

1. Connect the cart to a power source.
2. Plug in powered down devices.
3. Connected devices will automatically charge efficiently.
4. Connect/disconnect devices at any time.

Normal Operation :
Refer to the device for the level of charge. Connected devices will charge as fast and evenly as possible without drawing too much power.
When disconnecting devices, consider the charge level indicated by LED colors:

• Green LEDs: Charge Level >90%
• Blue LEDs: Device Charging
• White LEDs: Port Ready

FAQ :

• Q: Can devices be charged using USB-C emulator cables?
  A: Yes, devices can be charged using USB-C emulator cables, but it is recommended to use cables provided by JAR Systems for optimal performance and to prevent damage over time.

• Q: Where can I get additional support?
  A: For additional support, you can call 866.393.4202 or email Support@JAR- Systems.com.

Quick-Sense USB-C Charging Retrofit for Spectrum Cloud32 Cart
REBSCL32 Installation and User Guide

• Version A

• M00024

• Last Modified 06/21/2024
• For a copy of the most up-to-date manual, please contact a JAR Systems representative or visit:
• JAR-Systems.com/Support

Installation Instructions

Components

1. Install the top L brackets using 3 M5 screws and nuts on each. Secure them to the lowest vent in the side of the body of the cart with the screw on the outside and the nut on the inside.
   • Connect the power cable to the auxiliary outlet on the cart timer. The timer is secured in place with metal clips. If you need to, you can release the clips to connect the power cable. Connect the other end of the power cable to one of the charging hubs and set the hub on the top brackets
   • Secure the hub to the top brackets with 2 M5 screws and 2 nuts. The screw goes in through the bottom of the bracket and connects to the nut from the hub side. You will need to remove the USB-C cables on each end to make room for the angled wrench
2. Position the bottom Z brackets with the open ridge end towards the back of the cart. Clip in the bracket to the wall. The front of each bracket has two screw holes. Align the hole with the openings on the far left and right ends of the cart shelf. Use 2 M5 screws with nuts on each side. Insert the screws through the front and secure the nuts behind the lip of the shelf.
   • Connect the daisy chain cable in the back of the hub. The male plug goes through the top and connects to the hub on the left port. The other end connects to the bottom hub right port. Make sure to pass the cable through the right side of the opening/hole on the lower level in the cart. Set the second hub on the bottom brackets.
   • Secure the bottom hub to the brackets with 1 M5 screw and nut on each side. The nuts go from the top and the screws from the bottom

Normal Operation

• Plug the power cable into a standard 15A outlet. LEDs will illuminate white to indicate the cart is connected to a power source.
• Power off devices fully before connecting them to the cart for charging.
• Connect the devices to the USB-C charging cables. Ensure that devices are placed in the cart so that the charging ports are as close as possible to the USB-C charging port on the cart. Incorrectly connecting devices can strain the cable over long periods of time and lead to damage.
• You may hear a clicking sound, and the LED lights will change color according to the power draw of the attached devices.
• The system will automatically limit power consumption by turning some of the USB-C ports off temporarily
• Refer to the device for the level of charge. Connected devices will charge as fast and evenly as possible, without drawing too much power.
• To remove devices from the carts with the greatest level of charge first, disconnect devices with the green LEDs first before you disconnect devices with the blue LEDs.
• Devices that do not feature a USB-C charging port can be charged using USB-C emulator cables. (Not Included, contact JAR Systems for more info)

Quick Start

1. Connect cart to power source
2. Plug in powered down devices
3. Connected devices will automatically charge as efficiently as possible
4. Connect/disconnect devices any time

LED Charging Port Indicator Lights

•  White: Port Ready
• Blue: Device Charging
• Green: Charge Level >90%

TroubleShooting

• Always start troubleshooting with a simple reboot
  Unplug and replug the power cord. When the cart is connected to power, the LEDs will change color based on the power draw of connected devices (see light indication).

• Single Port or Device Issue

  • Ensure that both of the USB-C cable ends plug into the cart and the device correctly.
  • If there is still no charge, disconnect the device from that port (A) and plug into another port (B). If it is still not charging, it may be an issue with the device.
  • If charging begins when using port (B), exchange the cable from port (B) to port (A). If it begins to charge, the cable (A) is defective and will need to be replaced.

• Entire Charging Hub/Shelf Issue

  • Check the back of the charging hub to see if the cart’s power cable is plugged in and connected correctly.
  • When the cart is powered back on, the LED lights will begin to illuminate.

• Remove/Replace USB-C Cables

  • Each cable lock may be secured with up to three screws. Remove all screws with the supplied Torx key. Remove the cable lock. Unplug the cables from the USB-C ports and route them through the cable track. Reverse the process to replace a cable.

Warnings

• Power down all devices prior to connecting them to the hub for charging.
•  Keep away from moisture and harsh chemicals. Do not place any liquids near the charging cart.
• ny electrical equipment must be used by an adult or with adult supervision.
• Do not connect unsupported items to the cart or use for any purpose other than its intended use.
• Do not attempt to obstruct any ventilation openings or dismantle, open, or modify the system in any way.
• Do not sit or stand on the cart or charging hubs.
• Do not use an extension cable or daisy-chain to any other devices.
• Not intended for operation at altitudes greater than 2000 m or 6561 ft above sea level and should not be used in extreme temperatures. For indoor use only.

Disclaimer
Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty. Since the use of this information, the equipment connected, and the conditions by which any JAR Systems product is used is beyond the control of JAR Systems, it is the obligation of the owner and/or user to determine the correct and safe use of any equipment and product. To the extent that the law permits, any liability which may be incurred as a result of the use or future use of a product manufactured or sold by JAR Systems is limited to the cost of repairing or replacing the failed product or component at the discretion of JAR Systems either within, or outside of warranty periods, and does not extend to any loss or damage which may be caused as a consequence of misuse or failure of the equipment, product or the information contained herein. JAR Systems shall not in any event be liable for economic loss of profits, indirect, special, bodily injuries or consequential damages. Specifications and images are for illustration purposes only. Final product may differ and is subject to change without notice.

Warranty

• This product comes with a warranty that covers any defects in material or workmanship and extends to the original consumer of the product only. JAR Systems, LLC will replace the product with a new or refurbished product, repair the product, send replacement parts, or refund the purchase price of the product, at JAR Systems, LLC’s discretion. This warranty does not cover accidental damage, unreasonable use, neglect, tampering or other causes not arising from defects in material or workmanship.
• Any implied warranties last only as long as the warranty periods listed above except where state law does not allow limitations on how long an implied warranty lasts. This includes but is not limited to the implied warranties or merchantability and fitness. JAR Systems, LLC’s responsibility is limited to the actions listed above and nothing else.
• This warranty does not cover, and JAR Systems, LLC will not be responsible for, any damages due to loss of use of the product, or any other costs or expenses incurred by you or anyone else who uses the product, whether due to defects, breach of contract, negligence, strict liability or otherwise. JAR Systems is not liable for any indirect, special, incidental or consequential damages related to the product or this warranty. Some states do not allow exclusions or limitations on consequential or incidental damages, so these limitations or exclusions may not apply.
• This warranty gives you specific legal rights and you may also have other rights that vary from state to state. This warranty is governed by the laws of Florida, excluding its conflict of laws principles,  unless your state requires that its law be used. Contact JAR Systems for information on the length of warranty on your product(s).

For Additional Support  Call: 866.393.4202 or  Email: Support@JAR- Systems.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>