aCS ACR1555, ACR1555U NFC Bluetooth Reader User Manual
- July 31, 2024
- ACS
Table of Contents
- ACR1555, ACR1555U NFC Bluetooth Reader
- Product Information
- Specifications
- Product Usage Instructions
- Installing ACS Unified Bluetooth Driver
- Setting up Device Pairing with Built-in Bluetooth Adapter
- Q: What should I do if the Blue LED on ACR1555 is not blinking
- Q: Which Windows versions support device pairing with
ACR1555, ACR1555U NFC Bluetooth Reader
“`html
Product Information
Specifications
- Model: ACR1555
- User Manual Version: 1.02
- Contact: info@acs.com.hk
- Website: www.acs.com.hk
Product Usage Instructions
Installing ACS Unified Bluetooth Driver
-
Run the ACS Unified Bluetooth Driver.
-
The Setup Wizard will appear. Click OK to start the
installation. -
Click Next.
-
Click Next to install the driver to the default destination at
X:Program FilesAdvanced Card Systems LtdACS Unified Bluetooth
Driver 2.3.0.0 (X being your local Windows drive). -
Click Install.
-
Wait for the driver to install.
-
Once installation is complete, click Finish.
Setting up Device Pairing with Built-in Bluetooth Adapter
Note: This procedure is applicable for Windows
8 and later versions.
-
Turn on the ACR1555 by pressing and holding the power button
for 3 seconds until the Blue LED starts blinking, indicating
Bluetooth mode. -
If the Blue LED is not blinking, press and hold the Mode button
for 3 seconds to enter Bluetooth mode. -
Go to Settings, choose Bluetooth & devices, and turn on
Bluetooth. -
Click Add device.
-
In the Add a device pane, select Bluetooth and choose the
ACR1555 reader to pair. -
Press the Mode button again to complete the Bonding
process. -
The pairing is complete when the ACR1555 is connected.
-
The ACR1555 starts in HID mode. Open Notepad to display card
information when bringing NFC closer to the reader.
FAQ
Q: What should I do if the Blue LED on ACR1555 is not blinking
during setup?
A: If the Blue LED is not blinking, press and hold the Mode
button for 3 seconds to enter Bluetooth mode.
Q: Which Windows versions support device pairing with
ACR1555?
A: Device pairing with ACR1555 is supported on Windows 8 and
later versions. Windows 7 does not support devices using Bluetooth
5.3/Bluetooth Low Energy interface.
“`
ACR1555
ACR1555U NFC Bluetooth® Reader
User Manual V1.02
Subject to change without prior notice
info@acs.com.hk
www.acs.com.hk
Table of Contents
1.0. Introduction ………………………………………………………………………………………………. 3
2.0. For Windows® …………………………………………………………………………………………… 4
2.1.
Installing ACS Unified Bluetooth driver……………………………………………………………………….4
2.2.
Setting up device pairing with built-in Bluetooth adapter……………………………………………….7
ACR1555 User Manual
Version 0.02
Page 2 of 10
info@acs.com.hk
www.acs.com.hk
1.0. Introduction
ACR1555U NFC Bluetooth® Reader combines the latest technology in the world of
smart card readers with Bluetooth connectivity. This compact and wireless
smart card reader brings together sophisticated technology with fresh design
to meet different requirements in various smart card-based applications using
Bluetooth-enabled devices, such as smart phones and tablets.
This document provides general procedures for installation of drivers and
applications when using ACR1555U NFC Bluetooth® Reader .
Topics covered in this user manual are as follows:
Section 2.0 provides procedures on how to install ACS Bluetooth driver, pair
Bluetooth devices
2.0.
ACR1555 User Manual
Version 0.02
Page 3 of 10
info@acs.com.hk
www.acs.com.hk
2.0. For Windows®
2.1. Installing ACS Unified Bluetooth driver
To install the driver: 1. Run the ACS Unified Bluetooth Driver. 2. The Setup
Wizard will appear. To start the installation, click OK.
3. Then click Next.
4. Click Next to install the driver to the default destination, located at X:Program FilesAdvanced Card Systems LtdACS Unified Bluetooth Driver 2.3.0.0, with X being your local Windows drive.
ACR1555 User Manual
Version 0.02
Page 4 of 10
info@acs.com.hk
www.acs.com.hk
5. Click Install.
6. Wait while the driver installs.
ACR1555 User Manual
Version 0.02
Page 5 of 10
info@acs.com.hk
www.acs.com.hk
7. Once the installation is complete, click Finish.
ACR1555 User Manual
Version 0.02
Page 6 of 10
info@acs.com.hk
www.acs.com.hk
2.2. Setting up device pairing with built-in Bluetooth adapter
Note: This procedure only applies to Windows 8 and later. Windows 7 does not
support devices using Bluetooth 5.3/Bluetooth Low Energy interface.
To pair using this setup: 1. Turn on the ACR1555 by press and hold the power
button in 3 sec. the Blue LED will being blinking and enter the Bluetooth
mode. If the Blue LED is not blinking, you can press and hold the Mode button
at 3 sec to enter Bluetooth mode.
2. Go to Settings , choose Bluetooth & devices, 3. Turn on Bluetooth. 4. Click Add device
5. At the Add a device pane, click Bluetooth and select an ACR1555 reader to pair.
ACR1555 User Manual
Version 0.02
Page 7 of 10
info@acs.com.hk
www.acs.com.hk
6. Press again the Mode button to complete the Bonding process.
ACR1555 User Manual
Version 0.02
Page 8 of 10
info@acs.com.hk
www.acs.com.hk
7. The pairing is complete when you see that the ACR1555 is connected.
8. The ACR1555 start with HID mode. Please open the notepad to display the
card information when you bring the NFC closer to the reader.
Android is a trademark of Google LLC. The Bluetooth® word, mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Advanced Card Systems Ltd. is under license. Windows is a registered trademark of Microsoft Corporation in the United States and/or other countries.
ACR1555 User Manual
Version 0.02
Page 9 of 10
info@acs.com.hk
www.acs.com.hk
FCC Caution: Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: –Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver. –Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. –Consult the dealer or an experienced radio/TV
technician for help. FCC Radiation Exposure Statement: This equipment complies
with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm
between the radiator& your body.
ACR1555 User Manual
Version 0.02
Page 10 of 10
info@acs.com.hk
www.acs.com.hk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>