City Lights P1902-077-L Island Light Instruction Manual

: June 9, 2024
: City Lights

Table of Contents

City Lights P1902-077-L Island Light
Instruction
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

City Lights P1902-077-L Island Light

City Lights-P1902-077-L Island-Light-Product image

Instruction

WARNING
SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER AVERTIS SEMNT ! COUPERLE COURANT AUNIVEAU DES FUSIBLES OU DO DISJONCTER .

PREPARATION

Shut off power at the fuse box or circuit breaker box. If necessary remove the old fixture and mounting hardware.
Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
**MOUNTING THE FIXTURE (FIG. 1)

**

Align mounting plate (A) to the outlet box with junction box screws (B) (Size : #8-32*1/2L).
The side of the mounting back plate marked “GND” must face out.
ASSEMBLING THE FIXTURE (FIG.1)
Determine the desired hanging height and install the stems (H.I.J,K) to main body (L). Carefully pass the wire through each rod during assembly,
Thread nipple (G) into rods (H). Align faceplate (F) followed by canopy (E) onto nipple (G).
Pass the fixture wires (W) through washer (X) and secure with hex-nut (C).
Connect fixture wires (W) with the output wires on the driver (fixture red wire to driver red wire. Fixture black wire to driver black wire) making sure that all wire connectors are secured Fig.4.
CONNECTING THE WIRES (FIG. 2)
At this point, connect the electrical wires as shown in Fig.2, making sure that all wire connectors are secured. If your outlet has a ground wire (green or bare copper), connect the fixtures ground wire to it. Otherwise, connect the fixture ground wire directly to the mounting plate (A) using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
Place the fixture’s canopy (E) over the mounting back plate (A) and secure with screws (D/SIZE ‘M4*8MM).
**FINISHING THE INSTALLATION (FIG.3)

**

Attach the glass (N) to the supporter (V) that fix one the housing (M). While supporting the glass, and secure with screws (O).

CAUTION/ATTENTION
When handling the fixture, do not apply pressure to the LEDs, Hold the fixture by the base or housing (E) only.

IMPORTANT
Fixture should be installed by a qualified electrician to ensure proper wiring and installation. Dimmable with C-L (CFL & LED) type and Incandescent /Halogen type dimmers.

Replacing LED module (Fig. 3)

Warning: Shut off power off circuit bracket before replacing the LED module. The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details (Fig 3.)

Remove screws (O), and glass shades (N).
Remove the wire from connector (Z) on LED module
(R) by lightly pressing on the release button located on the top of the wire connector.
Carefully remove screws (T) and washer (S) to disconnect the LED module (R) from the heat conduction silicon (Q) and heat sink (P).
Remove the spacer (V) from the main body (L).
Reverse steps a-c for installing the new LED module.

Note: The LED module should be provided by a specified supplier.

DRIVER REPLACEMENT (Fig.4)
Warning: Shut off power off circuit bracket before replacing the driver. The driver can be replaced by a qualified electrician without cutting of wires and without damage to any decorative element to which the fixture is attached. See installation steps for more detail (Fig 4.)

Remove wire nuts (Z) and remove the old driver (Y) from canopy (E).
Remove the film on the double stick tape and attach the new driver into the back plate (A).

Brand : Lutron

City Lights-P1902-077-L Island-Light-06