NOBLE PRODUCTS 274GP1250 Glass Genie Electric Glass Polisher User Manual

NOBLE PRODUCTS 274GP1250 Glass Genie Electric Glass Polisher

Specifications

274GP1250

• Voltage: 120V AC 50/60Hz 1350W 12.5 Amps
• Capacity: Up to 330 glasses per hour
• Dimensions: 32.5 x 30 x 50cm I 12.8″W x 11.8″L x 19.7″H
• Weight: 15.5 Kgs / 34 lbs.
• Air Flow: 164 CFM
• Hot Air Temperature: 55-60°C / 130-140°F

274GP1600

• Voltage: 120V AC 50/60Hz 1600W 13.3 Amps
• Capacity: Up to 660 glasses per hour
• Dimensions: 57x30x50cm 22.4″W x 11.8″L x 19.9″H
• Weight: 18.3 Kgs / 40.3 lbs.
• Air Flow: 328 CFM
• Hot Air Temperature: 55-60°C / 130-140°F

Important Safety Information

CAUTION: THESE MARKS ARE USED AS A REFERENCE THROUGHOUT THIS MANUAL.

LIGHTNING FLASH IN TRIANGLE
This is used to alert the user of the presence of dangerous voltage that may create a risk of electric shock. Do not open cover.

EXCLAMATION POINT IN TRIANGLE
This is used to alert the user to:

• “CAUTION”: regarding important information regarding the care and use of this equipment.
• “WARNING”: regarding possibility of personal injury.

Important Safeguards

PLEASE READ THESE FIRST

Follow these basic safety precautions when using this electrical appliance to reduce the risk of fire, electric shock, and/or personal injury.

WARNING:
Plug unit only into a GROUNDED outlet that matches the voltage/cycle as listed on the motor. Outlet must be equipped with a UL/CSA approved ground fault circuit interrupter (G.F.C.I.).
WARNING:
Keep electrical cord clear of brushes and water.
WARNING:
DO NOT use machine if the power cord is cracked or damaged.
WARNING:
Disconnect from the power source before servicing.
WARNING:
Disconnect from the power source before servicing.
WARNING:
Ensure brushes are securely in place before turning machine on.
WARNING:
Do not touch the rotating brushes with hands.
WARNING:
Do not insert objects other than glass in between the rotating brushes.
WARNING:
Do not operate the machine without the brushes and air blower in place.
WARNING:
Do not place any objects into the glass polisher’s ventilation openings.
WARNING:
Loose clothing, long hair and jewelry can be caught in moving parts, posing an entrapment hazard.
CAUTION:
Use machine only for the purpose it was intended.
CAUTION:
Use only genuine replacement parts.

Assembly Instructions

1. Place unit on flat stable surface.
2. Attach blow tube onto the air blower base with the outlet on the blow tube facing the brush heads
3. Use screw provided to secure the blow tube in place.
4. Insert the short brush onto the middle drive shaft base, rotating it counter-clockwise to lock the notch of the brush to the drive shaft pin.
5. Repeat with remaining brushes onto the drive shafts.

NOTE: SEE TOP VIEWS OF THE POLISHERS FOR ACCURATE LOCATION OF COMPONENTS

Top View – 274GP1250 Glass Genie 5-Brush

Components List

Top View – 274GP1600 Glass Genie 8-Brush

274GP1250 Diagram

Glass Genie 5-Brush

274GP1600 Diagram

Glass Genie 8-Brush

Operating Instructions

NOTE: GLASSES MUST BE WASHED, RINSED, AND STILL DAMP WHEN INSERTED INTO THE GLASS POLISHER TO GET THE BEST RESULTS. DRY GLASSES ARE DIFFICULT TO POLISH.

1. Plug power cord into grounded outlet.
2. Press ON/OFF button to turn glass polisher ON.
3. Grasp glass at the base and insert onto center brush, holding glass base stationary or with slight up and down movement while center brush dries and polishes the inside of the glass and four outer brushes dry and polish the outside of the glass.
4. Remove glass from glass polisher.
5. Press ON/OFF button to turn glass polisher OFF when not in use.

NOTE: MOST GLASS TAKE 8-12 SECONDS TO POLISH, DEPENDING ON THE COMPLEXITY AND SIZE OF THE GLASSWARE.

Care and Maintenance

CLEANING THE POLISHER EXTERIOR

1. Ensure glass polisher is OFF and unplug power cord from the outlet.
2. Clean external surface of glass polisher daily using a dampened sponge. Do not immerse glass washer in water or spray with water.
3. Dry the surface with a soft cloth.

CLEANING THE BRUSHES

1. Ensure glass polisher is OFF and unplug power cord from the outlet.
2. Remove brushes by rotating each brush counter clockwise and pulling upward.
3. Wash brushes with mild laundry detergent and rinse well.
4. Use hands to squeeze as much water out of brushes as possible.
5. Insert short brush onto center post of the base.
6. Insert remaining brushes onto outer posts.
7. Plug power cord into a grounded outlet.
8. Press ON/OFF button to turn glass polisher ON. The air blower will dry the brushes in a few minutes.
9. Press ON/OFF button to turn glass polisher OFF when finished or not in use.

REPLACING THE BRUSHES

1. Ensure glass polisher is OFF and unplug power cord from the outlet.
2. Remove brushes by rotating each brush counter clockwise and pulling upward.
3. Insert short brush onto center post of the base.
4. Insert remaining brushes onto outer posts.

REPLACING THE FUSE

1. Using a slotted screwdriver, push on the fuse lightly and rotate it 90 degrees to the left. This will allow the fuse to come out. Reference Pic 1.
2. Disassemble the fuse from the fuse cover (the black part is the fuse cover) Reference Pic 2 & 3. Once removed, insert the new fuse into the fuse cover. Then insert the newfuse into the machine with a slotted screwdriver, rotating it 90 degrees to the right to lock the fuse in place.

Troubleshooting

Exploded View

274GP1250

Part Name

1. Bottom Plate As:si!mbly
2. M4x8 Large flat HIid 51:rew
3. Cepacltor1
4. Fuse
5. M6 Hex Fl•nge Nut
6. PowerCOrd
7. Min Motor
8. POWER Cord Fbclure
9. Wire Buckle
10. fnime Bnidm Assembly
11. M&xt2 Round Head Screw
12. Shaft Assembly
13. Heating Element
14. Heetlng Element Pfeuure Ring
15. Belt
16. M4 Heit Ser-Nut
17. Shell Support Bar
18. Shell Support Bar
19. Handle
20. Power Switch
21. M4x4 Flat HNd Screw
22. Hot Air Pipe
23. Long Brush
24. Short Brush
25. ShaftCowr
26. Drive Shaft
27. M4x1O Hexegon Stud
28. Mllx2O Hexagon Screw
29. 06 Spring Pad
30. 06FletPld
31. 010 Non-slip Pad
32. M1O Lo~oof Hex Nut
33. Joint Block
34. Motor
35. Capaclt0r2
36. Termlnal
37. M4x18 Round Screw
38. Foot
39. Foot Pad

Exploded ViEW

274GP1600

Part Name

1. Bottom Plate Assembly
2. M4*16 Round Screw
3. MS Hex Flange Nut
4. Capacitor 2
5. Capacitor 1
6. Terminal
7. Fan Motor
8. Fuse
9. Component Fixture
10. M4 Hexagon Screw Nut
11. Wire Buckle
12. Power Cord Fixture
13. Power Cord
14. Frame Bracket Assembly
15. MS*12 Round Head Screw
16. M4*1O Hexagon Stud
17. Shaft Assembly
18. Heating Element
19. Heating Element Pressure Ring
20. Handle
21. Shell
22. Power Switch
23. Shaft cover (optional)
24. M4*4 Flat Head Screw
25. Hot Air Pipe
26. Long Brush
27. Short Brush
28. M4*8 Large Flat Head Screw
29. Shell Support Bar
30. Belt
31. Drive Shaft
32. M6*2O Hexagon Screw
33. 06 Spring Pad
34. 06 Flat Pad
35. 010 Non-Slip Pad
36. M1O Lock-proof Hex Nut
37. Joint Block
38. Motor
39. 4 Screw
40. Foot
41. M4*2O Large Flat and Tip Tail Screw
42. Foot Pad
43. Brush Guard

Equipment Limited Warranty

Noble Products warrants its equipment to be free from defects in material and workmanship for a period of 6 months. This is the sole and exclusive warranty made by Noble Products covering your Noble Products brand equipment. A claim under this warranty must be made within 6 months from the date of purchase of the equipment. Only the equipment’s original purchaser may make a claim under this warranty. Noble Products reserves the right to approve or deny the repair or replacement of any part or repair request. The warranty is not transferable. Noble Products Equipment installed in/on a food truck or trailer will be limited to a period of 30 days from the original date of purchase.

To Make a Warranty Claim
For Warranty Inquiries contact the location where you purchased the product:

• WebstaurantStore.com: Contact help@webstaurantstore.com. Please have your order number ready.
• The Restaurant Store: If you purchased this unit from your local store, please contact your store directly.
• TheRestaurantStore.com: Online purchases, call 717-392-7261. Please have your order number ready.

Failure to contact the designated location prior to obtaining equipment service may void your warranty. Noble Products makes no other warranties, express or implied, statutory or otherwise, and HEREBY DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE.

This Limited Warranty does not cover

• Equipment sold or used outside the Continental United States
• Use of unfiltered water (if applicable)
• Noble Products has the sole discretion on wearable parts not covered under warranty
• Equipment not purchased directly from an authorized dealer
• Equipment used for residential or other non-commercial purposes
• Equipment that has been altered, modified, or repaired by anyone other than an authorized service agency
• Equipment where the serial number plate has been removed or altered.
• Damage or failure due to improper installation, improper utility connection or supply, and issues resulting from improper ventilation or airflow.
• Defects and damage due to improper maintenance, wear and tear, misuse, abuse, vandalism, or Act of God.

Any action for breach of this warranty must be commenced within 6 months of the date on which the breach occurred. No modification of this warranty, or waiver of its terms, shall be effective unless approved in a writing signed by the parties. The laws of the Commonwealth of Pennsylvania shall govern this warranty and the parties’ rights and duties under it. Noble Products shall not under any circumstances be liable for incidental or consequential damages of any kind, including but not limited to loss of profits.

www.nobleproducts.biz

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>