Peg Perego Pliko Mini Lightweight Pushchair Instructions
- June 4, 2024
- Peg Perego
Table of Contents
Peg Perego Pliko Mini Lightweight Pushchair
WARNING
IMPORTANT – READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
-
The child’s safety could be at risk if these instructions are not followed.
-
This product was designed for the transport of 1 child in the seat.
-
Do not use this product for a number of occupants greater than that intended by the manufacturer.
-
Pliko Mini is suitable from birth up to 22 kg or 4 years, whichever comes firts.
-
WARNING: Always use the restraint system. Always use the five-point safety harness.
-
Always lock the waist strap with the crotch strap.
-
For new born babies is recommended to use the backrest in the most reclined position
-
The front bar (if present) has not been designed to support the child’s weight; the front bar has not been designed to lift the seat with the child’s weight. The front bar does not replace the seat belt.
-
WARNING Ensure that all the locking devices are engaged before use.
-
WARNING Check that the pram body or seat unit or car seat attachment devices are correctly engaged before use.
-
WARNING To avoid injury ensure that the child is kept away when unfolding and folding this product.
-
WARNING Do not let the child play with this product. This product is not a toy.
-
WARNING The assembly and preparation of the product must be carried out by an adult.
-
Do not use this product if there are parts missing or signs of breakage.
WARNING Never leave the child unattended. -
Do not insert fingers into the mechanisms.
-
Be careful not to hurt the child when adjusting the mechanisms (handlebar, backrest … ).
-
Any load applied to the handle and/or the backrest and/or laterally to the product can compromise the stability of the product.
-
Do not load the baskets over 5 Kg. Do not put weight in the cup holder (if present) in excess of those indicated on the cup holders themselves and never hot drinks. Do not put loads of more than 0.2 Kg in the hood pockets (if present).
-
Do not use the product near to stairs or steps, heat sources, naked flames or dangerous objects within reach of the child.
-
Only replacement parts supplied or recommended by the manufacturer/distributor shall be used.
-
WARNING This product is not suitable for running or skating.
-
WARNING Do not add any mattress are not approved by the manufacturer.
-
Do not use accessories which are not approved by the manufacturer.
-
The images referring to the textile details may differ from the collection purchased.
-
For more information, consult our website: www.pegperego.com
INSTRUCTIONS
-
OPENING: to open the stroller, unhook the left hand side lever (fig_a), hold the handles and at the same time lift the stroller. Check that the stroller has opened properly by ensuring that the side hooks are well secured (fig_b).
-
If the hooks are not secured properly, press the seat downwards (fig_c) until they click into place. Finally, press downwards on PUSH with your foot (fig_d).
-
ASSEMBLING: to mount the front wheels, firstly check that the washer is present, as shown in the figure, then lower lever A and slip wheel B on until it clicks into place.
-
To mount the rear wheels connected by the brake cable, place them with the brake facing externally (fig_a).
WARNING: ensure the hooks have clicked into place, as in figure b. -
Finally, hook the central element of the brake cable onto the chassis, ensuring it clicks into place, as in the figure.
-
BASKET: to mount the basket, slip the loops over the rear hooks 1 and 2 and the front hook 3 (fig_a). ADJUSTING THE HANDLES: the height of the handles can be adjusted. Press the little button behind the handles and pull upwards. To lower the handles, do the opposite (Fig. b).
-
SWIVEL WHEELS: In order to make the wheels swivel, the lever (arrow 1) must be lowered. To secure the wheels, move the lever to the opposite direction (arrow 2). The rear wheels are fixed. BRAKE: To set the brake on the stroller, lower the lever on the rear wheel unit with your foot. To release the brake, lift the lever (fig_b). When stationary, always apply the brake.
-
HOOD: To fit the hood, click the fasteners onto the appropriate points until you hear them click (fig_a). Fasten the two side buttons as shown (fig_b – c). Finally, button down the hood on the rear of the stroller’s backrest (fig_d).
-
The hood can be adjusted into several positions by simply pulling it backwards or forwards. The hood includes a loop to be used to hang your child’s favourite toy.
-
5-POINT SAFETY HARNESS: to fasten, insert the two buckles of the waist strap (with attached shoulder straps, arrow a) into the leg divider strap until they click into place (arrow b). To unfasten them, press the button which is situated in the centre of the fastener (arrow c) and pull the waist strap outwards (arrow d).
-
To tighten the waist strap, pull on both sides in the direction of the arrow. To loosen it do the opposite.
-
It is possible to set the safety harness at 3 different heights, depending on how tall the child is. As the child gets bigger, the harness must be moved to a higher position.
-
To adjust the height of the safety harnesses, release the two buckles on the rear of the backrest. Pull the shoulder straps towards you (arrow a) until the buckles are released and insert them in the backrest loops (arrow b). Remove the shoulder straps from the sack (arrow c) and insert them in the most appropriate buckle (arrow d), then reattach the two buckles behind the backrest (arrow e). The buckles are securely attached when a click is heard (fig f).
-
LEG REST ADJUSTMENT: The leg rest can be set in 2 different positions. To lower the leg rest, pull the two side levers downwards and at the same time lower the leg rest. To raise the leg rest, push it upwards until it clicks into position (fig_a). BACKREST ADJUSTMENT: to adjust the backrest, lift the handle and recline it to the desired position. The backrest can be adjusted into different positions (fig_b).
-
FOLDING UP: pull one lever followed by the second lever upwards until you hear them click (fig_a); then, hold the central handle (fig_b) and pull it upwards until the stroller folds up. When folded, the stroller will stand upright (fig_c).
-
CARRYING: The stroller can be conveniently carried (with the front wheels set on stationary) by the central handle (fig_a). It can also be carried by the side handle (fig_b).
-
REMOVABLE LINING: to remove the lining from the stroller, unhook the fasteners on the rear of the backrest (fig_1), slip the fastener of the leg divider out from under the seat (fig_2), loosen the two screws (on both sides) using a screwdriver to keep the nut fastened (fig_3),
-
unhook the elastic from the chassis (fig_4), unhook the chassis (fig_5, see OPENING paragraph, point 1), slide the sack off the chassis (fig_6),
-
slide the sack off the footboard (fig_7). and pull the sack upwards (fig_8).
SERIAL NUMBERS
The Stroller PLIKO MINI has all the following relevant information behind the
backrest: product name, date of manufacture and serial number. This
information is required for any complaints.
THE ORIGINAL ACCESSORY PEGPEREGO
PegPerego accessories are designed as a useful, practical means of simplifying
the lives of parents. Discover all your product’s accessories on
www.pegperego.com
CLEANING AND MAINTENANCE
Cleaning must only be carried out by adults.
PRODUCT MAINTENANCE: protect from the weather: water, rain, or snow; prolonged
and continuous exposure to bright sunlight may give rise to colour changes of
various different materials; store this product in a dry place. The
maintenance have to be regularly. CLEANING THE CHASSIS: periodically clean all
plastic parts with a damp cloth. Do not use solvent or similar cleaning
products; keep all metal parts dry to prevent rusting; keep moving parts clean
(adjustment mechanisms, locking mechanisms, wheels, …) and free of dust and
sand and, if necessary, lubricate with light machine oil.
CLEANING FABRIC PARTS: Brush the fabric parts to remove dust.
- When washing, closely follow the instructions stated on the label sewn into the cover.
- Do not use chlorine bleach.
- Do not iron.
- Do not dry clean.
- Do not remove stains with solvents.
- Do not tumble dry.
PEGPEREGO S.p.A.
PegPerego SpA adopts a quality management system certified by TÜV Italia Srl
in accordance with the ISO 9001 standard. PegPerego can make changes at any
time to the models described in this publication for technical or commercial
reasons.
PEGPEREGO AFTER-SALES SERVICE
If any parts of the item get lost or damaged, only use genuine PegPerego spare
parts. For any repairs, replacements, information on the products and sales of
genuine spare parts and accessories, contact the PegPerego Assistance Service
and state the serial number of the product, if present.
tel. 0039/039/60.88.213 e-mail
[email protected] website
www.pegperego.com All intellectual property rights
on the contents of this manual are property of PegPerego S.p.A. and are
protected by the laws in force.