Peg Perego International VELOCE Stroller Plus Culla Grande Carrycot Instruction Manual
- June 14, 2024
- Peg Perego International
Table of Contents
Peg Perego International VELOCE Stroller Plus Culla Grande Carrycot
Thank you for choosing a PegPerego product.
WARNINGS
-
IMPORTANT : READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
The child’s safety could be at risk if these instructions are not followed. -
This item was designed to carry 1 child.
-
Do not use this item for a number of occupants exceeding that envisaged by the manufacturer.
-
WARNING: assembly and preparation operations must be performed only by adults.
-
Do not use this item if any parts are missing or broken.
-
WARNING: Ensure that all the locking devices are engaged before use.
-
WARNING: Check that the pram body or seat unit or car seat attachment devices are correctly engaged before use.
-
Always apply the brake when stationary and when loading or unloading children.
-
Do not insert fingers into the mechanisms.
-
Any weights hanging on the handlebar or handles could make the item unstable; follow the manufacturer’s instructions regards the maximum loads transportable.
-
Do not load the baskets over 7 Kg. Do not put weight in the cup holder (if present) in excess of those indicated on the cup holders themselves and never hot drinks. Do not put loads of more than 0.2 Kg in the hood pockets (if present).
-
WARNING: To avoid injury ensure that the child is kept away when unfolding and folding this product.
-
Do not let the child play with this product. This product is not a toy.
-
Never leave the child unattended.
-
Be careful not to hurt the child when adjusting the mechanisms (handlebar, backrest … ).
-
Do not use the product near to stairs or steps, heat sources, naked flames or dangerous objects within reach of the child.
-
Only replacement parts supplied or recommended by the manufacturer/distributor shall be used.
-
WARNING: This product is not suitable for running or skating.
-
Do not add any mattress not approved by the manufacturer.
-
Do not use accessories which are not approved by the manufacturer.
-
Any load applied to the handle and/ or the backrest and/or laterally to the product can compromise the stability of the product.
-
This product was designed for use in combination with PegPerego products. For more information, consult our website: www.pegperego.com
Veloce (Chassis + Seat)
This product is suitable for babies from birth up to 4 years or 22 kg, whichever comes first. For babies weighing more than 15 kg, direct and use the seat exclusively following the direction of travel.
- WARNING: Always use the restraint system. Always use the five-point safety harness. Always lock the waist strap with the crotch strap.
- The front bar has not been designed to support the child’s weight; the front bar has not been designed to lift the seat with the child’s weight. The front bar does not replace the seat belt.
- For new born babies it is recommended to use the backrest in the most reclined position.
- WARNING: do not use the rain canopy (if present) in interiors and check the child is not too hot; do not leave near sources of heat and keep away from cigarettes. The rain canopy must not be used on a stroller without a hood or parasol it can attach to. Use the rain canopy only under adult supervision. Check the rain canopy does not interfere with any moving mechanism in the chassis or stroller. Remove the rain canopy before folding the chassis or stroller.
Veloce Chassis + Car Seat
is approved for children from birth up to 13 kg of weight. When used in
combination with the car seat, this product does not replace a cot or a bed.
Should your child need to sleep, then it should be placed in a suitable pram
body, cot or bed.
Compatible items:
- PRIMO VIAGGIO SL
- PRIMO VIAGGIO SLK
- PRIMO VIAGGIO LOUNGE
Veloce Chassis + Pram Body:
is approved for children from birth up to 9 kg of weight. When used in
combination with the pram body: this product is suitable for a child who
cannot sit up by itself, roll over and a cannot push itself up on its hands
and knees. Maximum weight of the child: 9 kg. The carrying handle (if present)
should be left outside the pram body and out of the child’s reach during use.
Compatible items:
- CULLA GRANDE
- CULLA GRAN PAGODA
- CULLA BELVEDERE
The images referring to the product details may differ from the collection purchased. For more information, consult our website: www.pegperego.com
INSTRUCTIONS CHASSIS
-
OPENING: Before opening the frame, if present, remove (without using blades) all the die-cut cardboard elements.
- Press the two side buttons on the handle bar and rotate it in line with the frame tube (fig.a).
- Press the button under the handle bar (fig. b) and fully press the central button on the handle bar (fig. c).
- Open the chassis, release both buttons (b-c) and lift the handle bar upwards (fig.d) until it is fully open and clicks into place (fig_e).
-
FITTING THE WHEELS:
To assemble the front wheels, fit them into the slots until they lock into place (fig_a). To assemble the rear wheels, fit them into the slots until they lock into place (fig_b). -
FITTING THE REAR WHEEL MUD FLAP:
Insert and attach the mud flaps, as shown, on the supports attached to the chassis’ rear wheel mounts. To remove or replace them: press in the opposite direction and pull out. -
OPENING THE SEAT: Open the seat from the ends, lifting the backrest until it clicks into place.
-
FITTING THE BASKET:
First fasten the front part of the basket: slide the side ties into the channels along the frame (fig.a) and then fasten the three Velcro straps as shown (fig.b-c). -
Fitting the rear part of the basket:
Slide the side ties into the channels along the frame uprights (fig.a) and then fasten the Velcro strap as shown, making sure you take in the tube (fig.b). CAUTION! If you do not hook the basket on correctly, as shown, the basket will be unable to support the weight of loads placed in it. -
FIXED OR SWIVELLING FRONT WHEELS: To lock the front wheels, rotate the lever inwards (fig_a); to release the wheels and make them swivel, rotate the lever outwards (fig_b).
On difficult terrain, we recommend using fixed wheels. -
ONLY FOR VELOCE TC
ADJUSTMENT OF THE REAR WHEEL SUSPENSIONS:
It is possible to adjust the rear wheel suspensions according to your needs, based on the type of terrain and the weight of your child.
SOFT: turn the knob towards you to make the suspensions softer
HARD: turn the knob away from you to make the suspensions harder
WARNING: ALWAYS adjust both rear wheel suspensions in the same way. -
BRAKE: To brake the frame, press the rear of the pedal and check that the indicator is red (fig a).
To unlock the frame, press the front of the pedal and check that the indicator is green (fig b). -
ADJUSTABLE HANDLE BAR: To adjust the height of the handle bar, simultaneous press the side buttons, rotate the handle bar to the required position, and release the buttons (fig_a).
FITTING THE CUP HOLDER: It is possible to fasten the cup holder to one of the mushroom buttons on the frame, located both to the right and the left of the handle bar (fig_b). -
CLOSING THE CHASSIS WITH THE SEAT FASTENED:
It is possible to close the chassis with the child seat mounted both forward- facing and rear-facing.
FORWARD-FACING:
Close the hood, pull the backrest adjustment handle and fold this fully forward until it closes . -
Align the handle bar with the frame (fig. a), press the button under the handle bar (fig. b) and fully press the central button on the handle bar (fig. c).
Close the chassis, release both buttons (b-c) and push the handle bar downwards (fig d), holding the chassis vertical until it clicks into the closed position (fig.e). -
REVERSING THE SEAT ON THE CHASSIS:
To release the seat, press the buttons on both sides as shown (fig_a) and simultaneously lift the seat (fig_b). Fasten the seat to the chassis, either in the forward-facing (fig_c) or the rear-facing (fig_d) position. To secure the seat to the frame/ support, place it on the fastening devices until it clicks into place. IMPORTANT: Ensure the seat is properly fastened. -
REAR-FACING:
Close the hood, pull the backrest adjustment handle (fig_1) and fold this fully forward until it closes (fig_2). -
Align the handle bar with the frame (fig. a), press the button under the handle bar (fig. b) and fully press the central button on the handle bar (fig. c).
Close the chassis, release both buttons (b-c) and push the handle bar downwards (fig d), holding the chassis vertical until it clicks into the closed position (fig.e). -
TRANSPORT: The stroller can be conveniently carried, with the front wheels in fixed position, using the handle bar aligned with the frame (fig_a).
To reduce the overall dimensions, you can lower the handle bar (fig.b). -
WHEEL REMOVAL
All the wheels can be removed to make the stroller even more compact. To remove the rear wheels: press the button as illustrated and remove the wheel (fig_a). To remove the front wheels: press the button under the footrest as illustrated and remove the wheel (fig_b). -
OPENING THE FRAME WITH A FORWARD-FACING CHILD SEAT:
Align the handle bar with the frame (fig. a), recline the chassis, press the button under the handle bar (fig. b) and fully press the central button on the handle bar (fig. c). Open the chassis, release both buttons (b-c) and lift the handle bar upwards (fig. d) until it is fully open and clicks into place.
Lift the backrest (fig. e) until it clicks into place (fig. f). -
OPENING THE FRAME WITH A REAR-FACING CHILD SEAT:
Align the handle bar with the frame (fig. a), recline the chassis, press the button under the handle bar (fig. b) and fully press the central button on the handle bar (fig. c). Open the chassis, release both buttons (b-c) and lift the handle bar upwards (fig. d) until it is fully open and clicks into place.
Lift the backrest (fig. e) until it clicks into place (fig. f) -
POSSIBLE USES
SERIAL NUMBERS -
Veloce has the information on the product’s production date on the rear tube of the frame.
- Product name, production date and serial number of the frame. This information is essential in the event of a claim.
INSTRUCTIONS SEAT
-
HOOD: To use the hood, pull it out completely until it clicks into place.
The hood comes with a window, as shown. -
The hood can be extended thanks to a practical zip (fig
- It also comes with a further section that can be drawn out for more shade (fig b).
-
Baby’s ideal napping position is obtained by pulling the hood and lowering the stroller’s backrest completely.
-
FOOT MUFF (if present): slide the foot muff under the front bar, unbutton the first side buttons of the hood (fig.a), and button the sides of the foot muff to the unfastened buttons of the hood (fig.b). Finally, fasten the two buttons under the footrest (fig.c).
-
To remove the hood, release it from the tube of the chassis as shown in the figure.
-
To reattach the hood, ensure the hook coincides with the pin on the back of the tube of the chassis.
-
FOOTREST: To adjust the footrest to the desired position, press the button on both sides and lower (fig.a) or lift (fig.b) the footrest.
-
FRONT BAR: The front bar can be removed by pressing the two buttons at its extremities (fig_a), or opened on one side by pressing only one of the two side buttons (fig_b). To reattach it, slide it into the applicable slots, press the buttons and push it in until it clicks into place (fig.c)
-
BACKREST: To adjust the backrest, lift the handle bar (fig_a) and lower it to the desired position (fig_b). The adjustable backrest can be locked into a number of positions.
-
5-POINT SAFETY HARNESS: to fasten, insert the two buckles into the waist strap (with the straps attached in the crotch strap) until you hear a click (fig_a). To unfasten them, press the button which is situated at the centre of the seatbelt buckle and pull the waist strap outwards (fig_b).
-
To tighten the waist strap, pull on both sides in the direction of the arrow; to loosen it, do the opposite.
-
The safety harness can be adjusted in 3 positions according to the child’s height. You must use the higher positions as the child grows bigger.
-
Adjust the height, inserting the straps with shoulder pads through the eyelet in the backrest (fig_a) and pull them through the desired eyelets (fig_b).
-
The seat can be folded. Release it from the frame, close the hood, release the front bar, and press the backrest adjustment handle as shown.
-
REMOVING :
To remove the seat lining:
unfasten the inner button on both sides of the seat (fig_a), unfasten the 4 buttons on the seat (fig_b), on the back of the stroller, pull the backrest adjustment handle out from the fabric (fig_c). -
Release the crotch strap under the seat base (fig_d) and open the zip at the bottom of the back of the backrest (fig_e). You can now remove the lining.
-
Turn the lining inside out (fig. f), lift the rigid structure and remove the safety belts from the slots (fig. g).
Remove the rigid part completely (fig. h). -
REPOSITIONING THE LINING: To reposition the lining, perform these operations in reverse order, but MAKE SURE you start by repositioning the rigid part in the relevant lining pocket, and then reposition and fasten the safety belts through the slots. Now, once the rigid part has been inserted completely, you can reposition the lining.
-
SERIAL NUMBERS
Information relating to the production date of Seat can be found on the seat, under the lining.- The product name, production date and serial number of the frame.
This information is required for any complaints.
THE ORIGINAL ACCESSORY PEGPEREGO
PegPerego accessories are designed as a useful, practical means of simplifying
the lives of parents. Discover all your product’s accessories on
www.PegPerego.com
CLEANING AND MAINTENANCE
Cleaning must only be carried out by adults.
PRODUCT MAINTENANCE: protect from the weather: water, rain, or snow;
prolonged and continuous exposure to bright sunlight may give rise to colour
changes of various different materials; store this product in a dry place.
Conduct regular checks and maintenance on all the main parts
CLEANING THE CHASSIS: regularly clean plastic parts with a damp cloth; do
not use solvents, degreasers or aggressive detergents; keep all metal parts
dry to prevent rust; using a damp cloth, keep all moving parts (adjustment
mechanisms, securing mechanisms, wheels…) free of dust or sand. Regularly
clean the wheel pins with a dry cloth; do not use silicone-based sprays.
PEGPEREGO S.p.A.
PegPerego SpA adopts a quality management system certified by TÜV Italia Srl
in accordance with the ISO 9001 standard. PegPerego can make changes at any
time to the models described in this publication for technical or commercial
reasons.
PEGPEREGO AFTER-SALES SERVICE
If any parts of the item get lost or damaged, only
use genuine PegPerego spare parts. For any repairs, replacements, information
on the products and sales of genuine spare parts and accessories, contact the
PegPerego Assistance Service and state the serial number of the product, if
present.
tel. 0039/039/60.88.213
e-mail: [email protected]
website: www.pegperego.com
All intellectual property rights on the contents of this manual are property
of PegPerego S.p.A. and are protected by the laws in force.
Declaration of conformity
- Product name: VELOCE / VELOCE TC
- Product reference number: IP26 / IP29
- Reference Standards (origin): EN 1888-2:2018+A1:2022, EN 71-2:2011+A1:2014, EN 71-3:2013+A1:2014, Regolamento (CE) N. 1907/2006 – All. XVII pt 16, 17, 43, 51, 52 (REACH)
- Declaration of conformity: PegPerego S.p.A. declares under its sole responsibility that the article to which this declaration relates has undergone internal testing and has been approved, in accordance with regulations in force, by external, indepen-dent testing laboratories.
- Date and place of issue: Arcore, July 2023, PegPerego S.p.A. Via De Gasperi, 50 20862 Arcore (MB), ITALY
PegPerego S.p.A.
VIA DE GASPERI 50 20862 ARCORE MB ITALIA
tel: 0039 039 60881
Servizio Post Vendita – After Sale:
tel: 0039 039 6088213
PegPerego U.S.A. Inc.
3625 INDEPENDENCE DRIVE FORT WAYNE INDIANA 46808
Call us toll free: 1 800 671 1701
PegPerego CANADA Inc.
585 GRANITE COURT PICKERING ONTARIO CANADA L1W3K1
Call us toll free: 1 800 661 5050
www.pegperego.com
All of the intellectual property rights for the contents of this instruction
manual belong to PegPerego S.p.A. and are protected by the laws in force.