NICOR DGF43120SRD DGF Recessed Gimbal LED Downlight Instruction Manual
- June 9, 2024
- NICOR
Table of Contents
NICOR DGF43120SRD DGF Recessed Gimbal LED Downlight
WARNING:
- Risk of electric shock. Disconnect power at fuse or circuit breaker before installing or servicing.
- To prevent early lamp failure, lamp should only be installed in operating environments between -20°C and + 40°C (-4°F and 104°F)
- No user serviceable parts inside. To avoid electric shock do not disassemble product.
- This product is not intended for use in emergency light fixtures or exit signs.
- This product contains a chemical known to the state of California to cause cancer, birth defects and other reproductive harm.
- Risk of fire or electrical shock.
- prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
ATTENTION:
- Turn power off before inspection, installation, or removal.
- Suitable for use in dry, and damp locations. Use only on 120 VAC, 60Hz circuits.
What’s In The Box
Tools Needed
This LED Recessed Downlight requires very few tools for installation. A
screwdriver, a wrench, and a pair of wirecutters will help to install the
driver and downlight . Additionally, the installer must provide one Romex
connector.
Installing the DGF LED Recessed Downlight
Make sure all power is turned off before beginning installation
-
Identify fixture location and use the included paper template to cut the mounting hole.
*metal roughin template available -
Attach Romex connector to junction box.
-
Make wiring connections as follows:
- a. Connect Black wire to line wire.
- b. Connect White wire to neutral wire
- c. Connect Green wire to ground wire
-
Tighten Romex connector clamp. Select desired CCT by sliding switch in driver box and and close junction box.
-
Connect light engine. Be sure to properly align connectors and fully screw down connector cover.
-
Place driver box into ceiling.
( Optional: Mount using mounting tabs and screws)
-
Push up spring-arms on side of fixture, lift into ceiling, and release spring-arms.
-
Turn on power and enjoy your new lighting.
WARRANTY
LED EXPRESS LIMITED WARRANTY
Subject to the exclusions below, each NICOR LED product, including the LED
electronics and components of a property installed NICOR LED product, will be
free from defect in materials and workmanship for a period of five (5) years
from the original date of purchase. The product shall be considered defective
only if 10% or more of the product’s LED components fail. NICOR LED product
warranty covers the following performance criteria: LED Light Output will be
maintained above 70% of initial output; LED color temperature will not shift
more than 200K in CCT; LED driver will operate within NICOR specifications;
and the fixture finish, excluding natural aluminum or brass products, will not
exhibit cracking, peeling, excessive fading, or corrosion during the warranty
period. Exceptions apply as defined in NICOR’s product specification sheets,
which are incorporated by reference herein.
This limited warranty is provided to you, the purchaser of the product
identified on Seller’s invoice, as your exclusive remedy and applies only to
NICOR products that have been purchased from an authorized NICOR Distributor;
the product was new and in an unopened NICOR package at the time of
installation; and the NICOR product was installed by a licensed electrician or
under the supervision of a licensed electrician and used by consumers in the
United States or Canada when accompanied with this warranty. This warranty
extends only to the first consumer purchaser and is not transferable. A
consumer wishing to invoke the terms of this limited warranty must first
obtain a RGA number within 30 days of discovery of the defect, and return the
product to NICOR for inspection. Once verified to be covered by this limited
warranty, NICOR will, at its sole discretion, repair, replace, or refund the
purchase price of any product that does not conform to this limited warranty.
If NICOR, at its sole discretion, determines that the product should be
repaired or replaced, this warranty is limited to the reasonable, customary,
and necessary costs and expenses associated with the repair/replacement. This
warranty requires that all repair/replacement estimates and costs, including
but not limited to equipment rental (if any), and any other cost or expense to
be incurred in the repair/replacement of the product, be approved in advance
and in writing by NICOR. FAILURE TO OBTAIN NICOR’S ADVANCE WRITTEN APPROVAL OF
ALL REPAIR/REPLACEMENT COSTS AND EXPENSES IN WRITING SHALL VOID THIS LIMITED
WARRANTY.
THIS LIMITED WARRANTY DOES NOT COVER THE FOLLOWING:
- Defects or damages resulting from improper installation, operation, storage, misuse or abuse, accident, or neglect;
- Defects or damages resulting from improper service, testing, adjustment, installation, maintenance, alteration, connection to out-of-specification electrical service, corrosive or damp environments, or connection to incompatible equipment or devices (e.g., connecting non-dimmable lighting products to dimmers);
- Damage which occurs in transit;
- Power surges or overheating due to external conditions
- Acts of nature including but not limited to lightning strikes
FCC
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO
THE DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR, REPLACEMENT, OR
REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY
OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED. IN NO EVENT SHALL NICOR BE LIABLE, WHETHER IN CONTRACT OR IN TORT
(INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE
PRODUCT, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF
ANY KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS OR OTHER FINANCIAL
LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE THE
PRODUCT TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>