Radial engineering Power-1 Surge Suppressor and Power Conditioner Owner’s Manual
- June 9, 2024
- Radial engineering
Table of Contents
Power-1 Surge Suppressor and Power
Conditioner
Owner’s Manual
INTRODUCTION
The Radial Power-1 rackmount power supply and surge suppressor gives
musicians, engineers, producers, studio owners, commercial facilities, and
anyone working with valuable electronic equipment protection from power surges
that can damage or destroy music equipment instantaneously.
Unlike competitive products that utilize low quality MOV’s (Metal Oxide
Varactors) for surge protection, Radial’s Power-1 is built using a USA made
MOV. This critical component has been proven to offer superior thermal
protection and have a much longer lifespan than the alternatives. An LED
indicator on the front panel illuminates when the MOV is active, giving you
visual confirmation that your gear is protected from voltage spikes.
Created with audio professionals in mind, the Power-1 employs shunt mode
technology and avoids passing contaminated signals to the ground for lower
system noise. Additionally, a high-rejection RF interference filter is used to
keep high frequencies and AM radio signals out of the power line, preventing
contamination of audio signals.
Eight rear panel outlets are provided (four with wall-wart spacing to
accommodate any PSU size), along with three front panel outlets and a USB
charging port to easily power personal devices. A heavy-duty power on/off
toggle switch, rugged outlet connectors, and steel construction ensure that
the Power-1 performs night after night without fail.
BEFORE YOU GET STARTED
Thank you for purchasing the Radial Power-1 rackmount power supply unit.
Before using the Power-1, please read this short manual and heed all warnings
and safety precautions listed. Your safety is our top priority! Should you
have any questions, please review the FAQ page for this product at
www.radialeng.com, or contact us directly at
support@radialeng.com.
Note: The Power-1 is a surge suppressor, meaning it blocks high voltage
spikes that can damage connected equipment. It does not, however, regulate or
stabilize the incoming voltage; this is a task that requires a product called
an AC voltage regulator, and may be beneficial for applications where
unreliable or unsteady power sources are employed.
FRONT & REAR PANEL FEATURES
- FRONT PANEL OUTLETS: These outlets are always on, even when the front panel on/off switch is set to ‘off’. When using the Power-1 as a power source for equipment racks, this allows you to easily connect and charge devices without powering on the entire rack.
- USB CHARGING PORT: 5V/1A USB charging port for mobile devices such as smartphones and tablets. Type-A USB connection.
- FAULT PROTECTION INDICATOR: This LED illuminates when the Power-1’s Metal Oxide Varactor (MOV) is actively working, providing fault protection against varying resistance and high-voltage spikes from the AC main power source. The MOV is designed to recover from overvoltage events, providing continuous protection for your equipment. Should this LED turn off, immediately remove the Power-1 from the AC main power source and contact Radial technical support for assistance.
- ON/OFF: Large rocker switch with backlit LED activates the eight rear panel power outlets. Raised metal flanges on either side of this control help prevent accidental switching. If the Power-1 is connected to the AC main power source and the LED for the on/off switch doesn’t illuminate, check the circuit breaker on the rear panel.
- RACK EARS: Allow for mounting in standard 19” equipment racks, taking up 1 rack unit (1RU) of space.
- POWER CABLE: Hardwired cable for connection to the AC main 120V power source. 9.5′ (290cm approx.).
- CIRCUIT BREAKER: The Power-1 is rated for 15A of current, if this load is exceeded the circuit breaker will pop to help prevent damage to the Power-1 and connected devices. Should the circuit breaker pop, unplug the Power-1 from the AC main power source and press in the circuit breaker to reset it, then power back up as normal with a lower load connected to the Power-1.
- REAR PANEL OUTLETS: Eight rear power outlets are provided, four with additional spacing in between each outlet to accommodate for large ‘wall-wart’ power supplies. These power outlets are controlled by the front panel on/off switch.
SPECIFICATIONS*
IEC POWER PORTS
Voltage Rating: ………………………..120V, 50/60Hz
Load Rating: ……………………………15A total, 15A per outlet
USB POWER PORT
Voltage Rating: ………………………..5V
Load Rating: ………………….1A
GENERAL
Overload Protection: …………………………………….American-made Metal Oxide Varactor (MOV),
15A circuit breaker
Dimensions (L x W x H): ………………………….19” x 6.38” x 1.47” (482.6mm x 162.0mm x
37.4mm)
Weight ………………………………….6.5lb (5.03kg)
Temperature Range: …………………..5°C to 40°C
Agency Listings: …………………….Conforms to UL Std 1419, 60950-1 and 60065 in USA,
CSA Std 60950-1, C22.2 No. 62368 in Canada
Warranty: ………………………Radial 3-year, transferable
*Specifications are subject to change without notice.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE.
WARNING – IMPORTANT SAFETY INFORMATION
-
READ INSTRUCTIONS
All the safety and operating instructions of your Power-1 should be read before power is applied to the equipment. Retain this user manual for future reference. -
HEED WARNINGS AND OPERATING INSTRUCTIONS
All warnings on the equipment and operating instructions are important and should be followed. -
HEAT, WATER AND MOISTURE
The equipment should be kept away from areas of high temperature, i.e., heater vents, radiators, stoves/ovens, fireplaces, etc. The equipment should not be used in or around water, or in areas prone to flooding. -
POWER SOURCES
The equipment should be connected only to a power source of the same voltage and frequency as that listed on the rear panel above the power cord entry point. -
POWER CORD PROTECTION
Power cords should be arranged so they do not interfere with the movement of objects in the room: people, fan blades, utility carts, etc. Also, care should be taken that the cord is not pinched or cut, and placed so it is not in danger of being pinched or cut. -
POWER CORD GROUNDING
The power supply cord is of a three wire grounded type, designed to reduce the risk of electric shock. It is assumed to be of suitable length for most uses of the equipment. The use of extension cords and power strips is discouraged unless they are of suitable rating to deliver the required total current for safe operation of all connected equipment. Furthermore, extension cords or power strips must provide the same three wire grounded connection. It is important that the blades of the equipment’s plug be able to fully insert into the mating receptacle. Never remove the round grounding pin on the plug in an attempt to mate to a two wire ungrounded receptacle. -
NON-USE PERIODS
During periods of extended non-use, the power cord should be unplugged from the power source. -
LIQUID ENTRY
Care should be taken so that liquids such as cleaning fluids or beverages are not spilled into the enclosure of the equipment. -
DAMAGE REQUIRING SERVICE
Equipment should be serviced by qualified service personnel when:
A. The power supply cord or plug has been damaged,
B. Liquid has been spilled into the equipment, or the equipment has been exposed to rain,
C. The equipment has been dropped, or the enclosure has been damaged, or
D. The PROTECT LED on the front panel no longer illuminates when the equipment is connected to a power source. -
NO USER ACCESSIBLE PARTS
The Power-1 has no user accessible parts inside the device and should only be serviced by a qualified technician.
NOTICE
Radial Engineering Ltd. shall under no circumstances be held responsible for
any loss, damage or injury resulting from the use of this product in a manner
inconsistent with any of the procedures outlined in this document. The user is
responsible for determining whether this product is appropriate for the
intended application. Radial Engineering Ltd. is not responsible for any
indirect, secondary or ancillary loss or damage, including personal injury,
loss of or damage to property or loss of income resulting from the operation
or failure of this unit.
Notes —–
RADIAL ENGINEERING LTD.
3 YEAR TRANSFERABLE WARRANTY
RADIAL ENGINEERING LTD. (“Radial”) warrants this product to be free from
defects in material and workmanship and will remedy any such defects free of
charge according to the terms of this warranty. Radial will repair or replace
(at its option) any defective component(s) of this product (excluding finish
and wear and tear on components under normal use) for a period of three (3)
years from the original date of purchase. In the event that a particular
product is no longer available, Radial reserves the right to replace the
product with a similar product of equal or greater value. To make a request or
claim under this limited warranty, the product must be returned prepaid in the
original shipping container (or equivalent) to Radial or to an authorized
Radial repair center and you must assume the risk of loss or damage. A copy of
the original invoice showing date of purchase and the dealer name must
accompany any request for work to be performed under this limited and
transferable warranty. This limited warranty shall not apply if the product
has been damaged due to abuse, misuse, misapplication, accident or as a result
of service or modification by any other than an authorized Radial repair
center.
THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE FACE HEREOF AND
DESCRIBED ABOVE. NO WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT
NOTLIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE SHALL EXTEND BEYOND THE RESPECTIVE WARRANTY PERIOD
DESCRIBED ABOVE OF THREE YEARS. RADIAL SHALL NOT BE RESPONSIBLE OR LIABLE FOR
ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS ARISING FROM THE USE
OF THIS PRODUCT. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS, WHICH MAY VARY DEPENDING ON WHERE YOU LIVE AND WHERE
THE PRODUCT WAS PURCHASED.
To meet the requirements of California Proposition 65, it is our
responsibility to inform you of the following:
WARNING: This product contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Please take proper care when handling and consult local government regulations
before discarding.
All trademarks belong to their respective owners. All references to these are
for example only and are not associated with Radial.
Radial Engineering Ltd.
1845 Kingsway Ave, Port Coquitlam BC V3C 1S9
604-942-1001 •
www.radialeng.com
info@radialeng.com
Radial Power-1 Owner’s Manual v1.9 / 07-2022
Specifications and appearance are subject to change without notice.
Copyright © 2021 Radial Engineering Ltd.
www.radialeng.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>