Hytera HM65X Digital Mobile Radio User Guide
- October 27, 2023
- Hytera
Table of Contents
Hytera HM65X Digital Mobile Radio
Product Layout
Palm Microphone
You can request your dealer to program the Top Key (TKk), PI key, andP2 key as
shortcuts to assignable radio features
Basic Operation
Turn On or Off the Radio
On the HM65X or the palm microphone, long press the On-Off key.
Adjust the Volume
You can adjust the volume on the microphone.
- On the home screen, press the < key to decrease the volume or the > key to increase the volume.
- Press the key to locate the cursor to and then press the key.
Select the Zone
- On the home sereen, press key to locate the cursor to the zone No., and then press the key.
- Press the preprogrammed Zone Up or Zone Down key.
Select the Channel
- On the home screen, press key to locate the cursor to the channel No., and then press the key.
- Press the preprogrammed Channel Up or Channel Down key.
- To direct to the preset channel, press the preprogrammed Preset Channel key.
Status Indications
LCD lcons
For more status icons, refer to the User Manual.
LED lndicator
| LED Indicat r | Radio Status |
|---|---|
| Flashes green | The radio is being turned on. |
| Glows green | The radio is receiving. |
| Glows red | The radio is transmitting. |
| Flashes orange slowly | The radio is scanning or roaming. |
| Flashes orange rapidly | The radio is in emergency mode. |
Glows orange
| Call hang time: No voice is being transmitted or received during a call. Within such a period, you can press and hold the PTT key and speak.
Flashes blue
| Every 3s| The BT feature is enabled, but no BT device is connected.
Every 1.5s
| ****
A BT device is connected.
| LED Indicator | Radio Status |
|---|---|
| Every 0.1s |
Call Services
To ensure optimal voice quality on the receiving radio, keep the microphone 2.5 cm to 5 cm away your month during speaking.
Make a Call on Digital Channel
- On the home screen, select a digital channel, and then press and hold the PTT key.
- Press the programmed One Touch Call key, and then press and hold the PTT key.
Make a Call on Analog Channel
Call Without Signaling
- a. On the home screen, select an analog channel.
- b. Press and hold the PTT key.
Call with Signaling
- On the home screen, select an analog channel.
- Press the PTT key or the preprogrammed One Touch Call key.
Emergency Call
The Emergency feature is configured and enabled by your dealer. For details, refer to the User Manual.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Verification of harmful interference by this equipment to radio or television reception can be determined by turning it off and then on. The user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a different circuit to that of the receiver’s outlet.
- Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Note: Changes or modifications to this unit not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment.
FCC Regulations
Federal Communication Commission (FCC) requires that all radio communication products should meet the requirements set forth in the above standards before they can be marketed in the U.S, and the manufacturer shall post a RF label on the product to inform users of operational instructions, so as to enhance their occupational health against exposure to RF energy.
Operational Instructions and Training Guidelines
To ensure optimal performance and compliance with the occupational/controlled
environment RF energy exposure limits in the above standards and guidelines,
users should always adhere to the followings:
Gain of antenna must not exceed
Antenna Installation: Install the antenna at least 50 cm away from your
body, in accordance with the requirements of the antenna
manufacturer/supplier.
This radio complies with IEEE and ICNIRP exposure limits for
occupational/controlled RF exposure environment at operating duty factors of
up to 50% and is authorized by the FCC for occupational use only.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
controlled environment . This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This equipment should be
installed and operated with minimum distance 50 cm between the radiator &you
body.
ISEDC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada licence-exempt RSS
standard (s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference,including interference that may cause undesired oneration of the device
SEDC Radiation Exposure Statement:
This equipment complies with ISEDC RF radiation exposure limits set forth for
an controlled environment . This transmitter must not be co located or
operating in conjunction with any other antenna or transmitter. This equipment
should be installed and operated with minimum distance 50cm between the
radiator &čyou body.
Hytera is the trademark or registered trademark of Hytera Communications
Corporation Limited.
© 2022 Hytera Communications Corporation Limited. All Rights Reserved.
Address: Hytera Tower, Hi-Tech Industrial Park North, 9108# Beihuan Road,
Nanshan District,
Shenzhen, People’s Republic of China
Postcode: 518057
https://www.hytera.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>