ZEVNI A04472 Kenon 6-Light Black Modern-Contemporary Chandelier Installation Guide
- June 8, 2024
- ZEVNI
Table of Contents
- ZEVNI A04472 Kenon 6-Light Black Modern-Contemporary Chandelier
- INSTRUCTION
- IMAGE FOR FINISHED PRODUCT
- TOOLS REQUIRED (NOT INCLUDED)
- PARTS TYPE & QTY INCLUDING
- ACCESSORIES & QTY ENCLOSED
- ASSEMBLY & INSTALLATION INSTRUCTIONS
- Turn off power
- Make installation
- ORDERING PARTS
- CLEANING
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZEVNI A04472 Kenon 6-Light Black Modern-Contemporary Chandelier
INSTRUCTION
Item Number: A04472
WARNING: To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
-
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position. -
Place the wall switch in the “OFF” position.
-
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools as below picture
PARTS TYPE & QTY INCLUDING
- (C) Single bar (1)
- (D) Green ground screw (1)
- (E) Canopy (1)
- (F) Loop (4)
- (G) Hex nut (1)
- (H) Cap nut (1)
- (I) Cord (3)
- (J) Iron plate (1)
- (K) Fixture body (1)
- (L) Socket (6)
- (M ) Iron shade (6)
- (N) Socket ring (6)
ACCESSORIES & QTY ENCLOSED
- (A) Wire connector (3)
- (B) Mounting screw (2)
- (O) Allen wrench (1)
- (P) Spacer (1)
ASSEMBLY & INSTALLATION INSTRUCTIONS
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Make pre-installation
Step A1: Adjust the length of cords (I) to achieve the desired height of the mounted fixture.
- Use Allen wrench (O) to unscrew the screws in strain reliefs (F), carefully pull and push cords (I) through canopy (E) and strain reliefs (F) to lengthen or shorten the length of cords (I).
- Once the desired height of fixture is achieved, carefully tighten the screws till snug.
Step A2: Unscrew socket rings (N) from sockets (L), and carefully place iron shades (M) on sockets (L), then secure them with socket rings (N).
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
-
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position. -
Place the wall switch in the “OFF” position.
Make installation
Step B1 : Unscrew hex nut (G) and cap nut (H) from single bar (C).
Step B2 : Attach single bar (C) to the outlet box with mounting screws
(B).
Note: the side of single bar (C) marked “GND” must face out.
Step B3 : If needed, shorten the length of fixture wires. At this point,
the remaining wire length measured above single bar (C) is at least 6″.
Step B4: Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
- Connect ground wires according to the below chart
- Connect wires according to the below chart
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step B5; Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening hex nut (G) and cap nut (H) onto the preassembled threaded nipple on single bar (C).
NOTE: The canopy (E) should be snug against the ceiling and cap nut (H).
If not, adjust the threaded length of the preassembled threaded nipple on
single bar (C):
- unscrew the preassembled hex nut;
- screw the preassembled threaded nipple in or out of single bar (C);
- when the secure length is achieved, tighten the preassembled hex nut and back to step B5.
Step B6: Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
Check everything is already installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and nonabrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
www.ihomeangel.com
+1 850 296 2377
Working hours : Mon – Fri 9:00 – 16:00 EST
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>