RYOBI R18ID2 18V Impact Driver Instruction Manual

RYOBI R18ID2 18V Impact Driver

Important!
It is essential that you read the instructions in this manual before assembling, operating, and maintaining the product.
Subject to technical modification.

Safety, performance, and dependability have been given top priority in the design of your impact driver.

INTENDED USE

• The impact driver is intended to be used only by adults who have read and understood the instructions and warnings in this manual, and can be considered responsible for their actions.
• The product is intended for fastening and removing screws and bolts.
• The product is intended for consumer use only.
• Do not use the product for any other purpose. Use of the product for operations different from intended could result in a hazardous situation.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING
Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.
The term “power tool’’ in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jeweler. Keep your hair and clothing away from moving parts. Loose clothes, jeweler or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

BATTERY TOOL USE AND CARE

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion.
• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

SERVICE

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

IMPACT DRIVER SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

• Ambient temperature range for tool during operation is between 0°C and 40°C.
• Ambient temperature range for tool storage is between 0°C and 40°C.
• The recommended ambient temperature range for the charging system during charging is between 10°C and 38°C.

ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.

• Ambient temperature range for battery during use is between 0°C and 40°C.
• Ambient temperature range for battery storage is between 0°C and 20°C.

TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions and regulations.
Follow all special requirements on packaging and labelling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, non-conductive caps or tape. Do not transport batteries that are cracked or leaking. Check with the forwarding company for further advice.

RESIDUAL RISKS
Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise and the operator should pay special attention to avoid the following:

• Damage to hearing caused by noise
  • Wear suitable hearing protection and limit exposure.
• Injury to the eyes
  • Wear protective eye shields or goggles when using the product.
• Injury caused by vibration
  • Limit exposure. Follow the instructions in Risk Reduction.
• Electric shock caused by contact with hidden wires
  • Hold the product only by insulated services.
• Injury caused by dust
  • Dust created by operating the product can cause respiratory injury. Wear appropriate dust control mask with filters suitable for protecting against particles from the material being worked on.

RISK REDUCTION
It has been reported that vibrations from handheld tools may contribute to a condition called Raynaud’s Syndrome in certain individuals. Symptoms may include tingling, numbness, and blanching of the fingers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking, and work practices are all thought to contribute to the development of these symptoms. There are measures that can be taken by the operator to possibly reduce the effects of vibration:

• Keep your body warm in cold weather. When operating the unit, wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
• After each period of operation, exercise to increase blood circulation.
• Take frequent work breaks. Limit the amount of exposure per day.

If you experience any of the symptoms of this condition, immediately discontinue use and see your doctor about these symptoms.

WARNING
Injuries may be caused, or aggravated, by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.

KNOW YOUR PRODUCT
See page 5.

1. Chuck
2. Direction of rotation selector
3. Variable speed switch trigger
4. Handle, insulated gripping surface
5. MAG TRAY™ screw holder
6. LED light
7. Bit storage
8. Single bit
9. Single bit
10. Bit adaptor
11. Battery port

MAINTENANCE

WARNING
The product should never be connected to a power supply when assembling parts, making adjustments, cleaning, performing maintenance, or when the product is not in use. Disconnecting the product from the power supply will prevent accidental starting that could cause serious injury.

WARNING
When servicing, use only original manufacturer’s replacement parts, accessories and attachments. Use of any other parts may create a hazard or cause product damage.

• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.

WARNING
Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.

WARNING
For greater safety and reliability, all repairs should be performed by an authorized service center.

ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing of as waste. The machine, accessories, and packaging should be sorted for environment-friendly recycling.

SYMBOLS ON THE PRODUCT

• Safety alert
• No-load speed
• Volts
• Direct current
• Revolutions or reciprocations per minute
• CE conformity
• Eurasian Conformity Mark
• Ukrainian mark of conformity
• Please read the instructions carefully before starting the machine.
• Hot surface
• Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

SYMBOLS IN THIS MANUAL

• Note
• Parts or accessories sold separately
• Speed, minimum
• Speed, maximum

The following signal words and meanings are intended to explain the levels of risk associated with this product:

• DANGER
  Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.

• WARNING
  Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

• CAUTION
  Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

• CAUTION
  (Without Safety Alert Symbol) Indicates a situation that may result in property damage.

PRODUCT SPECIFICATIONS

• 18V Impact driver
• Model R18ID2
• Voltage 18 V
• Coupler 6.35 mm (1/4”)
• Switch Variable speed
• No load speed 0 – 3200 min-1
• Max torque 200 Nm
• Impacts per minute 0 – 3600 IPM
• Weight – not incl. battery pack 1.22 kg
• Weight
• (According to EPTA procedure 01/2014)
• 1.65 kg(1.3Ah) –
• 2.40 kg(9.0Ah)
• Measured sound values determined according to EN 62841:
• A-weighted sound pressure level
• Uncertainty K
• LpA = 95.0 dB(A)
• 3 dB(A)
• A-weighted sound power level
• Uncertainty K
• LwA= 106.0 dB(A)
• 3 dB(A)
• Wear ear protectors.
• The vibration total values (triax vector sum) determined according to EN 62841:
• Vibration emission value
• Impact tightening of fasteners of the maximum capacity of the tool  ah = 11 m/s2
• Uncertainty K  1.5 m/s2

BATTERY AND CHARGER

• Model
• Lithium-ion
  • Compatible battery pack (not included)
  • RB18L13
  • RB18L15
  • RB18L20
  • RB18L25
  • RB18L30
  • RB18L40
  • RB18L50
  • RB18L90
  • Compatible charger (not included)
  • BCL14181
  • BCL14183H
  • RC18150
  • RC18627
  • RC18115
  • RC18120
  • RC18118C

VIBRATION LEVEL

WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm and organization of work patterns.

RYOBI® WARRANTY APPLICATION CONDITIONS

In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.

1. The warranty period is 24 months for consumers and commences on the date the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use. This warranty applies only on new products.
2. There is a possibility to extend for a part of the range of power tools (AC/DC) the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of products for extended warranty is clearly displayed in stores and / or on packaging and is contained within the product documentation. The end user is required to register his/her newly-acquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.
3. The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power supply. This warranty does not apply to:
   • any damage to the product that is the result of improper or lack of maintenance
   • any product that has been altered or modified
   • any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
   • any damage caused by non-observance of the instruction manual
   • any product not displaying the CE approval mark on the rating plate
   • any product that has been attempted to be repaired by a non-authorized warranty service center or without prior authorization by Techtronic Industries
   • any product connected to an improper power supply (amps, voltage, frequency)
   • any damage caused by external influences (water, chemical, physical, shocks) or foreign substances
   • normal wear and tear spare parts
   • inappropriate use, overloading of the tool
   • use of non-approved accessories or parts
   • Power tool accessories provided with the tool or purchased separately. including but not limited to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide etc.
   • Components (parts and accessories) subject to natural wear and tear, including but not limited to Service & Maintenance Kits, carbon brushes, bearings, chuck, SDS drill bit attachment or reception, power cord, auxiliary handle, transport carry case, sanding plate, dust bag, dust exhaust tube, felt washers, impact wrench pins & springs, etc.
4. For servicing, the product must be sent or presented to a RYOBI authorized service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organization. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
5. A repair / replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or products become our property. In some countries delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected.
6. This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.

AUTHORISED SERVICE CENTRES

ACD PLANT LTD

• 145 Southbank Road Coundon
• Coventry, West Midlands CV6 1FG
• Phone: 02476 594348
• Email: danmcgunigle@acdplant.co.uk
• Web: www.acdplant.co.uk

CBS Power Tools Limited

• Unit 4, V P Square Stores Bar Rd, Fungate
• Peterborough, Cambridge shire PE1 5YS
• Phone: 01733 343031
• Email: steve@cbspowertools.co.uk
• Web: www.cbspowertools.com

C D Power tools

• 76 Old Road
• Cherwell Morley, Leeds LS27 7TH
• Phone: 0113 2718494
• Email: info@cdpowertools.co.uk
• Web : www.cdpowertools.co.uk

C J Sinclair Limited

• 44 Victoria Road St Peters Broadtails, Kent CT10 2UG
• Phone: 01843 869400
• Email: repairs@cjsinclairltd.co.uk
• Web: www.cjsinclairltd.co.uk

Tool Tech Industrial Equipment

• 227 E Dunhill Road, Maroquin Coleraine, Co Londonderry BT514LQ
• Phone: 028 70359493
• Email: john@tooltech.org.uk

For an updated list of authorized service centers, visit http://uk.ryobitools.eu/header/service-and-support/service-agents.

DECLARATION OF CONFORMITY

• Techtronic Industries GmbH
• Max-Edyth-Strafe 10, 71364 Win Menden, Germany

Herewith we declare that the product

• 18V Impact driver
• Brand: RYOBI
• Model number: R18ID2
• Serial number range: 47509001000001 – 47509001999999

is in conformity with the following European Directives and harmonized standards 2006/42/EC, 2014/30/EU, 2011/65/EU, EN 55014-1:2017, EN 55014-2:2015, EN 62841-1:2015, EN 62841-2-2:2014  RoHS documentation is compiled according to EN IEC 63000:2018

• Todd Chipner
• Sr. Director, CPT Quality and Asia Regulatory & Safety Win Menden, Nov. 22, 2019
• Authorized to compile the technical file:
• Alexander Krug, Managing Director
• Techtronic Industries GmbH
• Max-Edyth-Strafe 10, 71364 Win Menden, Germany
• RYOBI is a trademark of Ryobi Limited, and is used under license.
• © 2019 Techtronic Cordless GP. All rights reserved.

Techtronic Industries GmbH

• Max-Eyth-Straße 10,
• 71364 Winnenden, Germany

References

• | A.C.D Plant Ltd - Plant and Tool Hire Coventry and throughout Warwickshire
• Power Tools and Garden Tools | CBS Power Tools UK
• CD PowerTools – Power tool maintenance and repairs in Leeds
• C.J Sinclair Ltd - The Power Tool Repair Centre – C.J. Sinclair
• Ryobi Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>