Shadow-Caster SC3-SM 3 Inch Series Surface Mount Underwater Light Instructions
- June 9, 2024
- shadow-caster
Table of Contents
SC3-SM 3 Inch Series Surface Mount Underwater Light
Instructions
PRODUCT INSTRUCTIONS
SC3-SM SERIES
3″ SERIES SURFACE MOUNT UNDERWATER LIGHT
SC3-SM 3 Inch Series Surface Mount Underwater Light
MODEL #S:
SC3-BB-ALSM
SC3-BB-BZSM
SC3-BW-ALSM
SC3-BW-BZSM
SC3-CC-ALSM
SC3-CC-BZSM
SCM-GW-ALSM
SC3-GW-BZSM
OPERATION
Single color versions: On and off only
Power Toggle Control (SC3-CC and SC3-BW) : Step to the next color by
quickly turning the power off and then on within 2 seconds. The SC3-CC will go
through the following colors: blue, white, green, red, aqua, blue-violet,
violet, magenta, yellow, purple, orange, and green-yellow. The SC3-BW will go
blue, white then back to blue.
Shadow-NETTM (SC3-CC only): Direct Digital Control compatible through
your boat’s touch screen, push button controller or Shadow-CasterTM app.
Shadow NETTM requires connection of orange and yellow Shadow-NETTM wires to a
compatible controller.
INSTALLATION INSTRUCTIONS
Please read completely before installation:
- Choose mounting location – The lights require water cooling and should be installed on a flat surface area that is below the water line. Also consider the area inside the boat where the wire will enter and make sure it will be accessible to retrieve the wire. It is NOT recommended to mount the lights on hull running surfaces.
- The template below can be used for finding an appropriate mounting location. Verify that the template matches the mounting holes on the light if using this as a drill template. Make sure you are drilling into a place where you can get to the hole from inside the boat in order to feed wire. Mark center drill location with pencil.
- Drill a 5/8″ diameter hole for the cable in the center hole location only (shown on template).
- If mounting to an aluminum hull you will need to purchase part number: SCM-GASKET-SC3SM or SCM-GASKET-SC3SM-BR for galvanic isolation to prevent corrosion.
- Feed the cable through the hull into the boat.
- With the light against the hull in the location to be mounted, use the actual mounting holes of the light to mark one mounting hole. Drill that hole with an appropriately sized drill (9/64 is typical for #8 screws). Be sure the drill is not over sized or undersized. An undersized hole can cause the screws to break, oversize the hole and the hole will strip. With the light in place thread a screw into the hole. Perform same steps for remaining holes.
- Place a sufficient amount of marine sealant on the hull around all holes to seal them against the light’s base plate.
- Fill the screw holes with sealant.
- Use provided screws to mount light to the hull. If alternate screws are used they must be silicon bronze. After mounting wipe off any excess marine sealant around the light. Gently remove any spots with denatured alcohol on a lint free rag or cloth.
CONNECTIONS
Red Wire: Positive 10-30V DC input. Typical Current draw is 2 amps at (12
volt) and 1 amp on a 24 volt system.
Black Wire : Common ground
Orange and Yellow Wire on CC versions only:
Shadow-NETTM Digital Communications. Connect to a compatible Shadow-NETTM
controller. See options such as SCMLC-PLUS.
Please Note: Shadow-NETTM will override power toggle control. For
multiple light installations, check the control and power distribution section
of our website for more information.
CARE AND MAINTENANCE
Clean your Shadow-CasterTM Marine LED lights frequently with a soft bristle
brush. We recommend that installed ShadowCasterTM Marine LED lights be cleaned
every 2 weeks for “live in water” boats, and rinsed every time the boat is
pulled out of the water to prevent marine growth buildup and bio-fouling.
SC3-ALSM MOUNTING
DRAWINGS ARE ACTUAL SIZE
SC3-BZSM MOUNTING
DRAWINGS ARE ACTUAL SIZE 
Designed & Manufactured in Clearwater, FL
© 2022 Shadow-Caster™
LEDs. All Right Reserved.
Shadow-Caster™ LED Lighting
2060 Calumet Street
Clearwater, FL 33765
p: +1 727.474.2877
e: info@shadow-caster.com
w: shadow-caster.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>