FRIGIDAIRE PMOS1980SS Professional 1.9 Cu. Ft. Smudge-Proof Stainless

Steel Over-The-Range Microwave

BEFORE YOU BEGIN

Read these instructions completely and carefully.
IMPORTANT: Save these instructions for local inspector’s use.

•  Observe all governing codes and ordinances.
• Note to Installer – Be sure to leave these instructions with the Consumer.
• Note to Consumer – Keep these instructions for future reference.
• Appliance is to be installed and grounding by a qualified technician.
• Product failure due to improper installation is not covered under the Warranty.

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to ensure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.

CAUTION: For personal safety, remove house fuse or open circuit breaker before beginning installation to avoid severe or fatal shock injury. CAUTION: For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this 63–85 pound (28.5–38.5 kg) product, plus additional oven loads of up to 50 pounds (22.7 kg) or a total weight of 113–135 pounds (51.3–61.2 kg).

• For personal safety, this product cannot be installed in cabinet arrangements such as an island or a peninsula. It must be mounted to BOTH a top cabinet AND a wall.

NOTE : For easier installation and personal safety, it is recommended that two people install this product.
IMPORTANT: PLEASE READ CAREFULLY. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK. The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance. You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded. Where a standard two-prong wall receptacle is encountered, it is very important to have it replaced with a properly grounded three-prong wall receptacle, installed by a qualified electrician.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT, DEFORM OR REMOVE ANY OF THE PRONGS FROM THE POWER CORD. DO NOT USE WITH AN EXTENSION CORD.

ELECTRICAL REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz, 15 amps and 1.8 kilowattts. This product must be connected to a seperate and dedicated supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating. The power supply cord and plug should be brought to a seperate and dedicated 15- to 20- ampere branch circuit single grounded outlet. The outlet box should be located in the cabinet above the microwave oven. The outler box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code.

DAMAGE—SHIPMENT/INSTALLATION

• If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement.
• If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.
• If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer.

PARTS INCLUDED

HARDWARE PACKET

| Nylon Grommet (for metal cabinets)| 1

You will find the installation hardware contained in a packet with the unit. Check to make sure you have all these parts.
NOTE: Some extra parts are included.

ADDITIONAL PARTS

| Installation Instructions| 1
Use & Care Manual| 1
| Separately Packed Grease Filters| 2
| Exhaust Adaptor| 1
| Glass Tray| 1
| Turntable Ring| 1
For some models| Convection
Wire Rack| 1
For some models| Shelf| 1
| Air Fry Pan| 1
| Air Fry Tray| 1

Tools you will need:

•  Tape measure
•  Hole saw
•  Stud finder or hammer
• Level
• Duct and masking tape
•  Scissors

• 1 Phillips screw driver

• Electric drill
• 3/16”, 1/2”, 5/8” drill bit
• Filler wood blocks for recessed bottom cabinets
• Tin snips

Mounting Space

• The space between the cabinets must be 30″ (76.2 cm) wide and free of obstructions.
• If you are going to vent your microwave oven to the outside, see Hood Exhaust Section for exhaust duct preparation
•  When installing the microwave oven beneath smooth, flat cabinets, be careful to follow the instructions on the top cabinet template for power cord clearance.
•  As a guide to installation, see page 25 for Mounting Template Information.
• If the cabinet depth, including the cabinet doors, is more than 13”, then the unit must be spaced out from wall using adequate materials supporting 150 lbs to allow proper top vent air exhaust/intake.

PLACEMENT OF THE MOUNTING PLATE
REMOVING THE MICROWAVE OVEN FROM THE CARTON/REMOVING THE MOUNTING PLATE

1. Remove the installation instructions, use and care, exhaust adapter, turntable ring, shelf, filters, glass tray and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven.
   please note: Do Not Remove plastic plug protective cover until just before hanging the unit.
   Keep the unit at least 8 inches away from the counter top edge to prevent dropping because of the heavy door .

2. Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam.
   

3. Pull the carton up and off the oven.

4. Cut the middle of the outer protective plastic bag to remove the mounting plate
   

5. Remove the screws from each end of the mounting plate. This plate will be used as the rear wall template and for mounting. Reinstall the screws into the holes where they were removed.

FINDING THE WALL STUDS

1. Find the studs, using one of the following methods:
   •  Stud finder – a magnetic device which locates nails.
   •  Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate a stud location.
2. After locating the stud(s), find the center by probing the wall with a small nail to find the edges of the stud. Then place a mark halfway between the edges. The center of any adjacent studs should be 16 (40.6 cm) or 24 (61 cm) from this mark.
3. Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD.

DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
Plate position-beneath flat bottom cabinet
Plate position-beneath recessed bottom cabinet with front overhang
Plate position-beneath framed recessed cabinet bottom
Your cabinets may have decorative trim that interferes with the microwave installation. Remove the decorative trim to install the microwave properly and to make it level.

THE MICROWAVE MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
If the cabinets have a front overhang only, with no back or side frame, install the mounting plate down the same distance as the front overhang depth. This will keep the microwave level.

1. Measure the inside depth of the front overhang.
2. Draw a horizontal line on the back wall an equal distance below the cabinet bottom as the inside depth of the front overhang.
3. For this type of installation with front overhang only, align the mounting tabs with this horizontal line, not touching the cabinet bottom as described in Step D.

ALIGNING THE WALL PLATE

CAUTION: Wear gloves during installation.

1. Draw a vertical line on the wall at the center of the 30″ wide space.
2. Draw a horizontal line on the wall at the bottom of “Rear Wall Template”.
3. Find a wall stud in area “E” of mounting plate Refer to section 1B. Finding the wall studs.
4. For attaching the mounting plate into stud drill a 3/16″ hole into wood stud. Drill a 5/8″ hole for toggle bolt in 1 other location (Hole A or Hole B) NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.

NOTE: Holes A and B are inside area E. If neither of Holes A and B are not in a stud, find a stud somewhere in area E and draw a circle to line up with the stud. It is important to have at least one wood screw mounted firmly in a stud to support the weight of the microwave. Set the mounting plate aside.

INSTALLATION TYPES  (Choose A, B or C)

This microwave oven is designed for adaptation to the following three types of ventilation:

• Recirculating (Non-Vented Ductless)
• Outside Back Exhaust (Horizontal Duct)
• Outside Top Exhaust (Vertical Duct)

NOTE: This microwave is shipped assembled for Recirculating. Select the type of ventilation required for your installation and proceed to that section.

RECIRCULATING (NON-VENTED DUCTLESS)

Models are shipped for recirculating exhaust. Some models have a disposable charcoal filter installed to help remove smoke and odors.

OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)
OUTSIDE TOP EXHAUST (VERTICAL DUCT)
NOTE: Read the pages 14-15 only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 10.

RECIRCULATING (Non-Vented Ductless)

INSTALLATION OVERVIEW

• Attach Mounting Plate to Wall
• Prepare Top Cabinet
• Check Blower Plate
• Mount the Microwave Oven
• Install or change Charcoal Filter

IMPORTANT NOTES:

• Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration.
• Make sure the motor wiring has been properly routed and secured, and that the wires are not pinched.

ATTACH THE MOUNTING PLATE TO THE WALL
Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.
NOTE: If the cabinet depth including the cabinet doors  is more than 13″”” then the unit must be spaced out from wall using adequate materials supporting 150 Ibs to allow proper top vent air exhaust/intake.

1. Remove the toggle wings from the bolts.

2. Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 3⁄4″ (19 mm) onto each bolt.
   To use toggle bolts:
   

3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
   NOTE: Before tightening toggle bolts and wood screw, make sure the bottom of the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet.
   CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall.

4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET
You need to drill holes for the top support screws and a hole large enough for the power cord to fit through.

• Read the instructions on the TOP CABINET TEMPLATE.
•  Tape it underneath the top cabinet.

NOTE: Adjust top template accordingly if the microwave is being spaced out from the wall due to cabinet depth (including cabinet doors) of more than 13″”””.

• Drill the holes, following the instructions on the TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

CHECK BLOWER PLATE

• Place the microwave in its upright position, with the top of the unit facing up.
• Check to see that the blower plate is correctly installed on the unit.

MOUNT THE MICROWAVE OVEN
FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use the handle or heat shield during installation. Do not remove the cardboard spacers between the heat shield and door.
NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.

•  We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf. IMPORTANT: If filler blocks are not used, case damage may occur from overtightening screws.
  

• Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.
  

• Attach the microwave oven to the top cabinet .

• Insert 2 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw.

• Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)
  

• Install grease filters. See the Use &&&& and Care packed with the microwave.

INSTALLING OR CHANGE THE CHARCOAL FILTER (Some Models)

NOTE: The charcoal filter is factory installed in some models. Refer to the Use and Care to see if yours is factory installed and for replacement information.
For models without the recirculation filter access door, follow these steps to replace or install a charcoal filter.

•  Unplug microwave oven or disconnect power.

• Open the microwave door and push the “PUSH” position on the Vent, and then the cover open.
  

• Remove the charcoal filter by pushing the top of the filter inwards,then pull it forward out from the unit.
  
  

• Slide the top of the new charcoal filter into the top of the filter cavity.
  

• Press the bottom of charcoal filter to place it into the correct position.
  

• Then close vent’s cover.
  

• Close the microwave door. Plug in microwave oven or reconnect power.

INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING

NOTE: If you need to install ducts, note that the total duct length of 31⁄4” x 10” (8.2 x 25.4 cm) rectangular or 5” (12.7 cm)diameter/ 6 ” (15.2 cm) diameter round duct  transition adaptor must be used. d A 5 ” (12.7cm)/ 6″ (15.2cm) diameter duct is acceptable to use.  should not exceed 140 equivalent feet (42.7 m).
Outside ventilation requires an EXTERNAL EXHAUST DUCT.
Read the following carefully.
NOTE: It is important that venting be installed using the most direct route and with as few elbows as possible. This ensures clear venting of exhaust and helps prevent blockages. Also, make sure dampers swing freely and nothing is blocking the ducts.
Exhaust connection:
The exhaust adaptor has been designed to mate with a standard 31⁄4” x 10” (8.2 x 25.4 cm) rectangular duct.
If a round duct is required, a rectangular-to-round

Maximum duct length:
For satisfactory air movement, the total duct length of 31⁄4” x 10” (8.2 x 25.4 cm) rectangular or 5” (12.7 cm) diameter/ 6 ”(15.2 cm) diameter round duct should not exceed 140 equivalent feet (42.7 m).
Elbows, transitions, wall and roof caps, etc., present additional resistance to airflow and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total duct length, add the equivalent lengths of all transitions and adaptors plus the length of all straight duct sections. The chart below shows you how to calculate total equivalent ductwork length using the approximate feet of equivalent length of some typical ducts.
IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper.
Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.

EXTERNAL EXHAUST DUCTING

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation.
IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper.

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation.
NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.

OUTSIDE BACK EXHAUST (Horizontal Duct)
INSTALLATION OVERVIEW

• B1. Prepare Rear Wall
• B2. Remove Blower Plate
• B3. Attach Mounting Plate to Wall
• B4. Prepare Top Cabinet
• B5. Adjust Blower
• B6. Mount the Microwave Oven
  

IMPORTANT NOTES:

• Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration.
• Make sure the motor wiring has been properly routed and secured, and that the wires are not pinched.

PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for outside exhaust.

• Read the instructions on the REAR WALL TEMPLATE.
•  Tape it to the rear wall.
• Cut the opening, following the instructions of the REAR WALL TEMPLATE.

REMOVE BLOWER PLATE
Remove and save the screw that holds the blower plate to the microwave. Lift off the blower plate.
ATTACH THE MOUNTING PLATE TO THE WALL
Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.

1. Remove the toggle wings from the bolts.

2. Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 3⁄4″ (19 mm) onto each bolt.
   To use toggle bolts:
   

3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
   NOTE: Before tightening toggle bolts and wood screw, make sure the bottom of the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet.
   CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall.

4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET
You need to drill holes for the top support screws and a hole large enough for the power cord to fit through.

• Read the instructions on the TOP CABINET TEMPLATE.
•  Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST

1. Remove and save screw that holds blower motor to microwave.
   

2. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit.
   

3. Roll the blower unit 90°
   Before Rotation
   After Rotation

4. Rotate blower unit counterclockwise 180°.
   Before Rotation After Rotation
   

5. Gently remove the wires from the grooves. Reroute the wires through grooves on other side of the blower unit.
   Before Rerouting
   After Rerouting
   Wires Routed Through Right Side Wires Routed Through Left Side.

6. Roll the blower unit 90° so that fan blade openings are facing out the back of the microwave.
   Before Rolling
   After Rolling
   

7. Remove the knockout plates in the back of the unit with snips. (For some models)
   Knockout Plates: Snip all 4 webs on each knockout panel and remove the metal knockouts for rear airflow. Please take care to remove any sharp edges created from removing the knockout plates.

8. Place the blower unit back into the opening.
   CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched, and that they are properly secured.
   NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven.

9. Secure the blower unit to the microwave with the original screw.
   

10. Replace the blower plate in the same position as before with the screw. Make sure the screw is tight.

11. Attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven.
    

Push in securely until it is in the lower locking tabs. Take care to assure that the damper hinge is installed so that it is at the top and that the damper swings freely.

MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use the handle or heat shield during installation. Do not remove the cardboard spacers between the heat shield and door.
NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.

• We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case damage may occur from overtightening screws.

• Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.
  

• Attach the microwave oven to the top cabinet.
  

• Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)
  

• Install grease filters. See the Use &&&& and Care packed with the microwave.

IMPORTANT: Remove the cardboard spacers between heat shield and door.

OUTSIDE TOP EXHAUST (Vertical Duct)

• Attach Mounting Plate to
• Wall Prepare Top Cabinet
• Adapting Microwave Blower for Outside Top Exhaust
• Check Damper Operation
• Mount Microwave Oven
• Adjust Exhaust Adaptor
• Connect Ductwork

IMPORTANT NOTES:

• Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration.
•  Make sure the motor wiring has been properly routed and secured, and that the wires are not pinched.

ATTACH THE MOUNTING PLATE TO THE WALL
Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.

1. Remove the toggle wings from the bolts.

2. Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 3⁄4″ (19 mm) onto each bolt.
   To use toggle bolts:
   

3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
   NOTE: Before tightening toggle bolts and wood screw, make sure the bottom of the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet.
   CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall.

4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET

You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor.

• Read the instructions on the TOP CABINET TEMPLATE.
• Tape it underneath the top cabinet.
•  Drill the holes, following the instructions on the TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

ADAPTING MICROWA VE BLOWER FOR OUTSIDE TOP EXHAUST

1. Place the microwave in its upright position, with the top of the unit facing up.
   Remove the screw that holds the blower plate to the microwave. Remove and save the screw holding the blower motor to the microwave.

2. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit.
   

3. Roll the blower unit 90° so that fan blade openings are facing out the top of the microwave.
   

4. Place the blower unit back into the opening.
   CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched, and that they are properly secured.

5. Secure blower unit to microwave with the screw removed in Step 1. Make sure the screw is tight.

6. Replace blower plate with the screw removed in Step 1. Make sure the screw is tight.
   

7. Attach the exhaust adaptor to the top of the blower plate by sliding it into the guides of the blower plate.
   

Push in securely until it is in the locking tabs. Take care to assure that the damper hinge is installed so that the damper swings freely.

CHECK FOR PROPER DAMPER OPERATION

• Make sure tape securing damper is removed and damper pivots easily before mounting microwave.
•  You will need to make adjustments to assure proper alignment with your house exhaust duct after the microwave is installed.

MOUNT THE MICROWAVE OVEN
FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use the handle or heat shield during installation. Do not remove the cardboard spacers between the heat shield and door.
NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.

• We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case damage may occur from overtightening screws.

• Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.
  

• Attach the microwave oven to the top cabinet.

• Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)
  

• Install grease filters. See the Use & and Care packed with the microwave.

ADJUST THE EXHAUST ADAPTOR
Open the top cabinet and adjust the exhaust adaptor to connect to the house duct. CONNECTING DUCTWORK

1. Extend the house duct down to connect to the exhaust adaptor.
2. Seal exhaust duct joints using furnance duct tape for high temperature applications.

BEFORE YOU USE YOUR MICROWAVE

1. Make sure the microwave oven has been installed according to instructions.
2. Remove all packing material from the microwave oven.
3. Install turntablering and glass tray in  cavity.
4. Plug power cord into a seperate and dedicated 15- to 20-amp electrical outlet.
5. Replace house fuse or turn breaker back on.
6. Read the USE & CARE Manual.
7. KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTOR’S USE.
8. FILL OUT PRODUCT REGISTRATION CARD AN SEND IN.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>