ENFORCER MVE-AH1H1-42YQ 4K Enhanced HDMI Long Range Extender Instruction Manual

June 9, 2024
ENFORCER

4K ENHANCED HDMI Long Range Extender

MVE-AH1H1-42YQ

Installation Manual

ENFORCER MVE-AH1H1-42YQ 4K Enhanced HDMI Long Range
Extender


The ENFORCER 4K ENHANCED HDMI Long Range Extender extends the range of HDMI signals by using an active transmitter and receiver to send video and audio, RS-232, and bi-directional IR over a single Cat5e/6 cable. It can send 1080p signals up to 492ft (150m) between the two units with zero signal loss, while 4K2K/UHD HDMI signals can be transmitted up to 394ft (120m). A single power supply can power both devices from either end of the installation.


  • Extends 1080p up to 492ft (150m) and 4K2K up to 394ft (120m)
  • Supports resolutions from 480i to 4K2K/UHD
  • Supports 18Gbps video bandwidth
  • Plug and play operation ­- comes as a complete set
  • HDCP 2.2 / HDCP 1.4 and DVI 1.0 compliant
  • Transmitter includes an HDMI loop output
  • Analog stereo output on receiver
  • Bi-directional IR, RS-232, and CEC pass-through
  • Supports HDF, HDR10+, Dolby Vision, and HLG
  • Includes one 24VDC power supply -­ set can be powered at either the transmitter or receiver

HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries

Parts List

1x Transmitter                1x Receiver
1x 24V Power adapter    4x IR Mounting clips
1x IR Transmitter           2x 3-Pin phoenix connector
1x IR Receiver                1x Manual

Specifications
Input video signal 3.3V
Input DDC signal 5Vp-p (TTL)
Maximum single link range 4K2K@60Hz
Deep color 48-bit
Video formats supported All HDMI 3D, HDCP 2.2
Audio formats supported LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby

TrueHD, Dolby Digital Plus (DD+), DTS-ES, DTS HD Master, DTS HD-HRA, DTS-X
L/R Audio formats| PCM 2.0
Output video| HDMI
Resolutions supported| 4K2K@50/60Hz, 4K2K@30Hz, 1080p, 1080i, 720p, 720i, 480p, 480i
Range| 1080p| 492ft (150m)
4Kx2K| 394ft (120m)
Video amplifier bandwidth| 18Gbps
Video input connector| HDMI Type A 19-pin female
Max. HDMI cable length (IN/OUT)| 4K@60Hz, 16′ (5m) / 4K@30Hz, 32′ (10m) / 1080p@60Hz, 50′ (15m)
Cat5e/6 wiring standard| T568-B
IR Pass-through| 20~60kHz
Operating voltage| 24VDC
Power supply| 1A@24VDC (1 adapter)
ESD protection (human body model)| ±8kV (air-gap discharge), ±4kV (contact discharge)
Current draw (both units total)| 390mA
Operating humidity| 20~90% (non-condensing)
Operating temperature| 32°~104° F (0°~40° C)
Dimensions| 5 ½”x 11/16″x2 9/16″ (140x18x65 mm)
Weight| Transmitter 5.6-oz (160g), Receiver 5.5-oz (155g)

Dimensions

Front                                                         Side
ENFORCER MVE-AH1H1-42YQ 4K Enhanced HDMI Long Range Extender
1

  1. Power LED
  2. Micro-USB port

Both transmitter and receiver have the same dimensions and the same front panel.

Overview

Transmitter

ENFORCER MVE-AH1H1-42YQ 4K Enhanced HDMI Long Range Extender
2

  1. Power input
  2. Link Data
  3. HDBT Out
  4. Data LED
  5. HDMI Loop-out
  6. HDMI In
  7. IR In
  8. IR Out
  9. RS-232

Receiver

ENFORCER MVE-AH1H1-42YQ 4K Enhanced HDMI Long Range Extender
3

  1. Power input
  2. Link Data
  3. HDBT In
  4. Data LED
  5. HDMI Out
  6. Audio Out
  7. IR In
  8. IR Out
  9. RS-232

Installation
  1. Determine the location of the transmitter and receiver and how much Cat5e/6 cable is needed.

  2. Connect the HDMI cable between the transmitter and source device.

  3. Connect the HDMI cable between the receiver and the display.

  4. Connect the Cat5e/6 cable between the receiver and transmitter.

  5. Connect the included 24VDC power adapter to either the transmitter or receiver.

  6. If any device will be controlled by the remote control:
    a. Plug the IR transmitter into the IR-OUT of the extender unit nearest the device to be controlled, pointing the IR transmitter toward the device’s IR window.
    b. Plug the IR receiver into the IR-IN port of the other extender unit so that the IR receiver will be easily visible to the remote control’s signal.
    NOTE: Maximum IR transmission distance of 26ft (8m) can only be achieved when the line of sight is directly in line. At about 45° the distance may be reduced to 16ft (5m).

  7. If desired, connect an RS-232 controller unit to the RS-232 terminal on the transmitter and connect the remote device to be controlled to the RS-232 terminal on the receiver.

  8. If desired, connect powered speakers to the Audio Out on the receiver.

  9. If desired, connect a monitor to the HDMI Loop Out of the transmitter.

Fig. 1 – HDBT Port LEDs

| Steady On| Flashing| Off
---|---|---|---
Link| Good| Poor| None
Data| HDMI with HDCP| HDMI only| No HDMI or HDCP

NOTES

  • High-quality Cat5e/6 cables are recommended, especially at longer distances.
  • Premium high-speed HDMI cables are highly recommended.
  • Both Cat5e/6 and HDMI cable lengths should be kept within the maximums shown in Fig. 2.

Fig. 2 – Maximum Cable Length Chart

Resolution 4K@60Hz 4K@30Hz 1080p@60Hz
Cat5e/6 394′ (120m) 492′ (150m)
HDMI 16′ (5m) 32′ (10m) 50′ (15m)
Sample Application

ENFORCER MVE-AH1H1-42YQ 4K Enhanced HDMI Long Range Extender
4

  1. Transmitter
  2. HDMI Matrix with RS-232
  3. AV Source
  4. Remote control for distant HDMI display
  5. Remote control for AV source
  6. Receiver
  7. HDMI Display

NOTES:

  • Only one power supply is used, either on the transmitter or receiver.

  • User either the IR IN on the transmitter and IR OUT on the receiver to control the distant HDMI display from the source, or the IR IN on the receiver and IR OUT on the transmitter to control the source from the distant display area.

Troubleshooting

HDMI device does not function correctly

  • Use T568-B wiring standard

  • Make sure the maximum lengths are not exceeded for either the HDMI or Cat5e/6 cable used (see Fig. 1, pg. 3)

  • Test the Cat5e/6 cable between the receiver and transmitter and make sure it is functional

  • Make sure that there are no problems with the HDMI source, HDMI cables, or HDMI display by plugging the source directly into the display using an HDMI cable

  • Make sure that the transmitter and receiver are plugged into the correct units

  • Make sure the HDMI source is compatible with the HDMI display

IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO- LARM will not be held responsible for the use of this product in violation of any current laws or statutes.


California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.


WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.


NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2022 SECO-LARM U.S.A., Inc. All rights reserved.


SECO-LARM ® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Phone: 949-261-2999 | 800-662-0800
Website: www.seco-larm.com
Email: sales@seco-larm.com

PICHN3

MI_MVE-AH1H1-42YQ_221019.docx

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ENFORCER User Manuals

Related Manuals