ASUS TUF Gaming VG249Q1 HD Monitor User Guide

ASUS TUF Gaming VG249Q1 HD Monitor

Notices

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and
• This device must accept any interference received including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003. The device may fall, causing serious personal injury or death. To prevent injury, this device must be securely attached to the floor/wall in accordance with the installation instructions

Safety information

• Before setting up the monitor, carefully read all the documentation that came with the package.
• To prevent fire or shock hazards, never expose the monitor to rain or your retailer.
• Never try to open the monitor The dangerous high voltages inside the monitor may result in serious physical injury.
• If the power supply is broken, do not try to fix it by Contacting a qualified service technician or your retailer.
• Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.
• Slots and openings on the back or top of the cabinet are provided for ventilation. Do not block these Never place this product near or over a radiator or heat source unless proper ventilation is provided.
• The monitor should be operated only from the type of power source indicated on the If you are not sure of the type of power supply to your home, consult your dealer or local power company.
• Use the appropriate power plug which complies with your local power
• Do not overload power strips and extensions Overloading can result in fire or electric shock.
• Avoid dust, humidity, and temperature extremes. Do not place the monitor in any area where it may become Place the monitor on a stable surface.
• Unplug the unit during a lightning storm or if it will not be used for a long period of This will protect the monitor from damage due to power surges.
• Never push objects or spill liquid of any kind into the slots on the monitor cabinet.
• To ensure satisfactory operation, use the monitor only with UL-listed computers that have appropriate configured receptacles marked between 100 ~ and 240V AC.
• The socket outlet shall be installed near the equipment and shall be easily accessible.
• If you encounter technical problems with the monitor, contact a qualified service technician or your retailer.
• Provide an earthing connection before the mains plug is connected to the And, when disconnecting the earthing connection, be sure to disconnect after pulling out the mains plug from the mains.

WARNING

• Usage of other than the specified head- or earphones can result in hearing loss due to excessive sound pressure.
• Please confirm the distribution system in building installation shall provide the circuit breaker rated 120/240V, 20A (maximum).
• If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3-pin outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter. The grounding pin is an important safety feature.

Care & Cleaning

• Before you lift or reposition your monitor, it is better to disconnect the cables and power cord. Follow the correct lifting techniques when positioning the When lifting or carrying the monitor, grasp the edges of the monitor. Do not lift the display by the stand or the cord.
• Turn your monitor off and unplug the power cord. Clean the monitor surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed with a cloth dampened with a mild cleaner.
• Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended for use with the LCD. Never spray cleaner directly on the screen, as it may drip inside the monitor and cause an electric shock.

The following symptoms are normal with the monitor:

• The screen may flicker during the initial use due to the nature of the fluorescent light. Turn off the Power Switch and turn it on again to make sure that the flicker disappears.
• You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
• When the same image is displayed for hours, an afterimage of the previous screen may remain after switching The screen will recover slowly or you can turn off the Power Switch for hours.
• When the screen becomes black or flashes, or cannot work anymore, contact your dealer or service center to fix Do not repair the screen by yourself!

Conventions used in this guide

WARNING: Information to prevent injury to yourself when trying to complete a task.
CAUTION: Information to prevent damage to the components when trying to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.

Where to find more information

Refer to the following sources for additional information and for product and software updates.

1. ASUS websites
   The ASUS websites worldwide provide updated information on ASUS hardware and software products. Refer to http://www.asus.com

2. Optional documentation
   Your product package may include optional documentation that may have been added by your dealer. These documents are not part of the standard package.

Welcome

Thank you for purchasing the ASUS® LCD monitor! The latest widescreen LCD monitor from ASUS provides a crisper, broader, and brighter display, plus a host of features that enhance your viewing experience. With these features, you can enjoy the convenience and delightful visual experience that the monitor brings you!

Package contents

Check your package for the following items:

1. LCD Monitor
2. Base
3. Quick Start Guide
4. Warranty Card
5. Power Cord
6. HDMI Cable (optional)
7. DP Cable (optional)

If any of the above items are damaged or missing, contact your retailer immediately.

Assembling the monitor

To assemble the monitor

1. Align the screw hole on the arm with the bundled screw on the base. Then insert the base into the arm.
2. Fix the base to the arm by fastening the bundled screw.

Base screw size: M6 x 17mm

Connect cables

The rear of the LCD monitor

1. Earphone – out Port
2. DP – in Port
3. HDMI2 Port
4. HDMI1 Port
5. AC-IN Port

Monitor introduction

Using the Controls button

Use the control button on the back of the monitor to adjust the image settings

1. Power Indicator:

   • The color definition of the power indicator is as the below table.
     Status| Description
     ---|---
     White| ON
     Amber| Standby mode
     OFF| OFF

2. Power Button:

   • Press this button to turn the monitor on/off.

3. GameVisual Button: This is shortcut 2.

   • Press this Shortcut to switch from seven video preset modes (Scenery Mode, Racing Mode, Cinema Mode, RTS/RPG Mode, FPS Mode, sRGB Mode, and MOBA Mode) with GameVisual™ Video Intelligence Technology.

4. GamePlus Button: This is shortcut 1

   • GamePlus: The GamePlus Function provides a toolkit and creates a better gaming environment for users when playing different types of games. Particularly, the Crosshair function is specially designed for new gamers or beginners interested in First Person Shooter (FPS) games.
   • To active GamePlus:
     • Press GamePlus Button to enter the GamePlus main menu.
     • Activate Crosshair, Timer, FPS Counter, or Display Alignment function.
     • Move the button up/down to select and press to confirm the function needed. Press to go off, and exit.
     • Crosshair/Timer/FPS Counter is movable by pressing a 5-way key.

5. Close Button:

   • Exit the OSD menu.

6. (5-way) Button:

   • Turns on the OSD menu. Enacts the selected OSD menu item.
   • Increases/Decreases values or moves your selection up/down/left/right

Adjusting the monitor

• For optimal viewing, we recommend that you look at the full face of the monitor, then adjust the monitor to the angle that is most comfortable for you.
• Hold the stand to prevent the monitor from falling when you change its angle.
• You can adjust the monitor’s angle from +23˚ to -5˚.

Detaching the arm/stand (for VESA wall mount)

The detachable stand of this monitor is specially designed for VESA wall mount.

To detach the arm/stand

1. Disconnect power and signal cables. Carefully put the monitor facedown on its EPS packaging.
2. Remove the four (4) screws securing the arm to the rear of the monitor.
3. Detach the stand (arm and base) from the monitor.

Outline dimension

Unit: mm

OSD (On-Screen Display) menu

How to reconfigure

1. Press Central of 5-way to activate the OSD
2. Press the DOWN and UP buttons to toggle between options in the Menu. As you move from one icon to another, the option name is
3. To select the highlighted item on the menu press the Center
4. Press the DOWN and UP buttons to select the desired
5. Press the Center key to enter the slide bar and then use the DOWN or UP  buttons, according to the indicators on the menu, to make your changes.
6. Press the ◄/► to move left/right

OSD Function Introduction

Gaming

This function contains six sub-functions that you can select for your preference.

• Overclocking: This function allows you to adjust the refresh
• OverDrive : The adjusting range is from 0 to
• AMD FreeSync Premium : It can allow an AMD FreeSync Premium-supported graphics source to dynamically adjust display refresh rate based on typical content frame rates for power-efficient, virtually stutter-free, and low-latency display
• ELMB : Check to decrease motion blur and minimize ghosting part when on-screen objects are fast-moving.
• GamePlus: Activate Crosshair, Timer or FPS Counter or Display Alignment
• GameVisual: This function contains seven sub-functions that you can select for your preference.
• GameVisual: This function contains seven sub-functions that you can select for your preference.
• Shadow Boost: Dark color enhancement adjusts the monitor gamma curve to enrich the dark tones in an image making dark scenes and objects much easier be found.
  • In the Racing Mode, the Saturation, and ASCR functions are not user-configurable.
  • In the sRGB Mode, the Saturation, Skin Tone, Color Temp., Brightness, Contrast, and ASCR functions are not user-configurable.
  • In the MOBA Mode, the Saturation and ASCR functions are not user-configurable.

Image

You can adjust Brightness, Contrast, VividPixel, ASCR, Aspect Control, and Blue Light Filter from this main function.

• Brightness : The adjusting range is from 0 to 100.
• Contrast: The adjusting range is from 0 to 100.
• VividPixel : ASUS Exclusive Technology that brings lifelike visuals for crystal-clear and detail-oriented The adjusting range is from 0 to 100.
• ASCR : Select ON or OFF to enable or disable the dynamic contrast ratio function, ASCR is Disabled when ECO mode or ELMB is on.
• Aspect Control : Adjusts the aspect ratio to “ Full ” and 4:3.
• Blue Light Filter: Adjust the energy level of blue light emitted from the LED backlight.

When Blue Light Filter is activated, the default settings of Standard Mode will be automatically imported.

• Between Level 1 to Level 3, the Brightness function is user-configurable.
• Level 4 is an optimized setting. It is in compliance with TUV Low Blue Light Certification. The Brightness function is not user-configurable.
• 4:3 is only available when the input source is in 4:3 format

Please refer to the following to alleviate eye strains:

• Users should take some time away from the display if working for long hours.
• It is advised to take short breaks (at least 5 mins) after around 1 hour of continuous working at the computer. Taking short and frequent breaks is more effective than a single longer break.
• To minimize eye strain and dryness in your eyes, users should rest their eyes periodically by focusing on objects that are far away.
• Eye exercises can help to reduce eye strain. Repeat these exercises often. If eye strain continues please consult a physician.
• Eye exercises:
  1. Repeating look up and down
  2. Slowly roll your eyes
  3. Move your eyes diagonally.
• High-energy blue light may lead to eye strain and AMD (Age-Related Macular Degeneration). Blue light Filter to reduce 70% (max.) harmful blue light to avoid  CVS (Computer Vision Syndrome).

Color

• Color Temp: Contains three preset color modes (Cool, Normal, Warm) and User Mode.
• Saturation: The adjusting range is from 0 to 100.
• Skin Tone: Contains three color modes including Reddish, Natural, and Yellowish.

In the User Mode, the colors R (Red), G (Green), and B (Blue) are user- configurable; the adjusting range is from 0 ~ to 100. Select the image color you like from this function.

Input Select

Select the input source from HDMI-1, HDMI-2, or DisplayPort input signal.

MyFavorite

You can adjust Shortcut and Customized Settings from this main function.

• Shortcut : The user can select from “GamePlus” , “GameVisual” , “Brightness” , “Contrast ”, “Blue Light Filter” , “Color ” , and “Volume” and set them as a shortcut key.
• Customized Setting : You can do your setting according to your favorite.

System Setup

Adjusts the system configuration.

• Language : Select OSD language. The selections are: English , French , German , Spanish , Italian , Dutch , Russian , Poland , Czech , Croatia , Hungary , Romania , Portugal , Turkey , Simplified Chinese , Traditional Chinese , Japanese , Korean , Persian , Thai, and Indonesian.
• Sound: Adjusts the output volume level or mute the audio.
• ECO Mode: Activate the ecology mode for power saving.
• Power Indicator : Turn the power LED indicator on/off.
• Power Key Lock : To disable/enable the power key.
• Key Lock : Disable all keys Press the down button for more than five seconds to disable the key lock function.
• OSD Setup: Adjusts the OSD Timeout, DDC/CI, and Transparency of the OSD screen.
• Information : Displays the monitor information.
• All Reset : Selects “ Yes ” to revert all settings to the factory default mode.

Specifications

Troubleshooting (FAQ)

ON mode.

•    Check if the power cord is properly connected to the monitor and the power outlet.

•     Check Power Indicator function in main menu OSD.

Select “ON” to turn on power LED.

The power LED lights amber and there is no screen image| •    Check if the monitor and the computer are in the ON mode.

•    Make sure the signal cable is properly connected the monitor and the computer.

•    Inspect the signal cable and make sure none of the pins are bent.

•     Connect the computer with another available

monitor to check if the computer is properly working.

Screen image is too light or dark| •    Adjust the Contrast and Brightness settings via OSD.
Screen image bounces or a wave pattern is present in the image| •    Make sure the signal cable is properly connected to the monitor and the computer.

•     Move electrical devices that may cause electrical

interference.

Screen image has color defects (white does not look white)| •    Inspect the signal cable and make sure that none of the pins are bent.

•     Perform Reset via OSD.

•    Adjust the R/G/B color settings or select the Color Temperature via OSD.

No sound or sound is low| •    Adjust the volume settings of both your monitor and computer.

•     Make sure the computer sound card driver is

properly installed and activated.

Supported Timing List

PC Timings List of HDMI / DP input

FAQ’s

Is the ASUS TUF gaming display worth the price?

Overall, ASUS’s TUF Gaming VG27AQ is a superb 165Hz IPS gaming monitor. It impressed us with its ELMB-Sync function, a very low reaction time + input latency coupled, color accuracy, and good ergonomics despite its pointless HDR-10 compatibility.

Can I play games on the ASUS TUF gaming monitor?

The monitor is fantastic. Its 165 Hz properly supports my Xbox series S and X. With games like GTA 5, Rocket League, Fortnite, and others, it is quite quick.

Touch screen for gaming on ASUS TUF?

By pressing the screen with your fingertips, the gadget is simple to use.

Do the ASUS TUF VG249Q speakers work?

Adjustable height, pivoting, blue light filtering, swiveling, frameless, tilting, flicker-free Internal Speakers Adjustable height, pivot, blue light filter, swivel, frameless, tilt, and flicker-free features.

What is the ASUS VG249Q’s refresh rate?

For professional gamers and fast-paced games, TUF Gaming VG249Q is a 23.8-inch, Full HD (1920×1080), IPS display with a quick 144Hz refresh rate.

Which ASUS gaming mode is the best?

We advise setting the GPU Mode to Ultimate in order to have the finest gaming experience. Then select GPU Mode under Device > GPU Power Saving.

Does the 120 refresh rate on the TUF gaming monitor exist?

For both PC and console gamers, the ASUS VG28UQL1A of the TUF Gaming delivers a high refresh rate UHD experience. For gaming consoles like the Xbox Series X and PS5, the monitor may give a “4K” 120Hz experience with HDMI 2.1 and support for VRR (Variable Refresh Rate).

The ASUS TUF display is it sturdy?

Although it doesn’t bring anything novel to the table in terms of design, durability more than makes up for it. As long as your system can keep up, the display can play contemporary video games at their highest settings. Even at lesser graphical settings, it can deliver fluid gaming at a refresh rate of 165Hz.

The best ASUS TUF gaming, which?

The Asus TUF F15 Gaming laptop is an excellent gaming laptop all around. Although it excels at other daily duties as well, its primary strength is gaming performance. The laptop is quick, has a nice screen, and a lovely backlit keyboard.

Has the ASUS TUF monitor Bluetooth capability?

Sorry, this model is not Bluetooth-enabled. A: You may purchase an adapter for your computer to connect to HDMI if it does not already have a display port installed. A: The Nvidia Quadro video cards and the display are compatible.

Why is the ASUS TUF display black?

The connecting cable is disconnected or loose. The monitor cannot or is not connected correctly. The driver or a system file is damaged. There are outdated graphics drivers.

Is the VG249Q a top-notch display?

The Asus VG249Q is a fantastic deal for gamers looking for a bright IPS panel that supports 144Hz refresh rates. With its low price and stunning image quality, it received an accuracy grade often reserved for prosumer devices.

Has VG249Q HDR technology?

A broad color gamut and HDR are also supported.

Is the ASUS monitor safe for your eyes?

Smart Dynamic Backlight Adjustment, a feature of ASUS Flicker-Free technology, reduces flicker and guards against eye strain, irritability, and weariness.

Does VG249Q support HDMI at 144Hz?

Please take note that only DisplayPort or HDMI within 48-144 Hz are supported for Adaptive-Sync technology.

Download this PDF Link:ASUS TUF Gaming VG249Q1 HD Monitor User Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>