CHIGEE G3 Tire Pressure Monitoring System User Manual

CHIGEE G3 Tire Pressure Monitoring System

TIRE PRESSURE PAIRINGS

External tire pressure sensor

1. Long Press and hold the “ ” and “ ”button at the same time for 5 seconds to enter pairing mode. until you hear a long beep）
2. When done, you will see that the pressure data is scrolling, which indicates that the front wheel is waiting to be paired.
3. During the time, screw a tire pressure sensor into the front wheel (It doesn’t matter whether the sensor is for the front wheel or rear wheel) and after receiving the tire pressure data, the front wheel pairing is over with a long beep.
4. Automatically switch to the rolling status of rear tire pressure, then screw another tire pressure sensor onto the rear wheel. Upon receiving the tire pressure data with two long beeps, the rear wheel pairing is over and the pairing process is automatically ended.

Please note that tire pressure may be incorrect during pairing due to installation problems, but tire pressure will be updated after normal driving.

Built-in tire pressure sensor

1. Make sure the tire is inflated to more than 2 Bar after installing the built-in tire sensor into the tire in advance.
2. Long Press the “ ”and “ ” button at the same time for 5 seconds to enter pairing mode. until you hear a long beep）
3. After finishing, the data scrolling on the front tire pressure shows the front tire is waiting to be paired.
4. It is now time to deflate the front wheels for six seconds, and upon receiving the tire pressure data until you hear a beep, then the front wheel pairing is done.
5. Then, the device automatically shifts into the scrolling phase. It is time to deflate the rear wheel for 6 seconds. After receiving the tire pressure data until it beeps twice, the rear wheel pairing will be done and then automatically exits. Watch the tire pressure data change on the display after re-inflating the front and rear tires to normal tire pressure.

Pairings single tire

1. Once in pairing mode, you can separately match the front and rear wheels by short-pressing the“ ”or“ ”button.
2. A toggle operation will exit after it is successful, and the next tire will not be automatically selected.

Press and hold the setting button“ ”to finish pairing.If there is no operation for 180 seconds, he pairing will be automatically ended.

ADJUST BACK-LIGHT BRIGHTNESS
In normal operation, you can toggle the back-light brightness by clicking on the setting button“ ” Three modes available to toggle: off /low light/high light.

Please note that turning off the backlight during the day helps to save power.

WORK AND HIBERNATION
When a vibration is detected, the system will automatically wake up and enter the working state. When the working state remains stationary for more than 60 seconds, it will put back into hibernation.

LOW-VOLTAGE PROTECTION
A battery with a low protection value will be forced into hibernation. Meanwhile, It will no longer respond to vibration, but only the charge will wake it.

BATTERY CHARGING
When the power icon“ ”with only one bar or blinks should be charged, use the attached magnetic charging line connected to the bottom of the monitor charging port (distinguish the direction). As the battery icon“ ” scrolls, it shows that it is charging at this time and stops scrolling when it is full.

PERFORMANCE PARAMETERS

• The Product name: Tire Pressure Monitoring Display
• Weight: 30g
• Operating temperature: -25-65℃
• Operating frequency: 433.92Mhz FSK
• Input voltage: 5V
• Battery capacity: 600mAh
• Battery voltage: 3.7V
• Hibernation and endurance: About 600 days
• Working duration: Approx. 160 days (1-hour ride per day)
• Battery model: BR1225
• Endurance time: 1 year
• Sensor measurement accuracy: 0.1Bar
• Sensor pressure monitoring range: 0-5Bar

FUNCTIONAL DESCRIPTION

STATE DESCRIPTION

SETTINGS

• Press and hold the set button“ ” for 2 seconds to enter the setting interface, then you will hear a long beep. After entering, a short press of set button“ ”will switch to the settings mode.
• Use the “ ” or “ ”button to adjust the parameter. Long press and hold the key to quickly adjust the digit.
• To exit, press and hold the set button “ ”for 2 seconds until it beeps twice.
• If there’s no operation in 60 seconds, the setting interface will shut down.

Order of parameter setting:

Long press to enter
High-pressure threshold setting for the front wheel

Press it once
Low-pressure threshold setting for the front wheel

Press it twice
High-temperature threshold setting for the front wheel

Press it 3 times
low-temperature threshold setting for the front wheel

Press it 4 times
High-pressure threshold setting for Rear wheel

Press it 5 times
Low-pressure threshold setting for Rear wheel

Press it 6 times
High-temperature threshold setting for Rear wheel

Press it 7 times
Low-temperature threshold setting for rear wheels

Press it 8 times
Pressure unit setting

Press it 9 times
Set Temperature units/temperature unit setting

FCC STATEMENT WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference e to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution:
Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>