Altronix AL600ULB UL Recognized Power Supply/Charger User Guide
- June 4, 2024
- Altronix
Table of Contents
Altronix AL600ULB UL Recognized Power Supply/Charger User Guide
Overview:
Altronix AL600ULB power supply/charger converts a 28VAC/200VA input to a 12VDC or a 24VDC output (see specifications).
Specifications:
Agency Listings:
- UL Recognized component for
**UL 294* Access Control System Units.
UL 1481** Standard for Safety for Fire Protective Signaling Systems.
Input:
- Input 28VAC / 200VA.
Output:
- 12VDC or 24VDC selectable output.
- 6A continuous supply current @ 12VDC or 24VDC.
- Filtered and electronically regulated output.
Supervision:
- AC fail supervision (form “C” contacts).
Supervision (cont’d):
- Low battery and battery presence supervision (form “C” contacts).
Battery Backup:
- Built-in charger for sealed lead acid or gel type batteries.
- Maximum charge current 0.7A.
- Automatic switch over to stand-by battery when AC fails.
- Zero voltage drop when switched over to battery backup.
Visual Indicators:
- AC input and DC output LED indicators.
Additional Features:
- Short circuit and thermal overload protection.
Board Dimensions (W x L x H approximate):
4.3” x 7.1” x 2.3” (109.2mm x 180.3mm x 58.4mm).
*Access Control Performance Levels: Destructive Attack – N/A; Endurance – IV; Line Security – I; Stand-by Power – IV.
Power Supply Output Selection:
Stand-by Specifications:
Installation Instructions:
The AL600ULB should be installed in accordance with article 760 of The National Electrical Code as well as NFPA 72 and all applicable Local Codes.
-
Mount the AL600ULB in the desired location/enclosure (mounting hardware included).
-
Set the AL600ULB to the desired DC output voltage by setting SW1 to the appropriate position (refer to Power Supply Output Selection chart).
-
Connect two (2) 28VAC/100VA transformers (connected in parallel) to the terminals marked [AC].
Use 14 AWG or larger for all power connections (Battery, DC output, AC input).
Use 22 AWG to 18 AWG for power-limited circuits (AC Fail/Low Battery reporting).
Keep power-limited wiring separate from non power-limited wiring (115VAC / 60Hz Input, Battery Wires).
Minimum 0.25” spacing must be provided.
CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing equipment.
There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel. -
Measure output voltage before connecting device. This helps avoiding potential damage.
-
Connect devices to be powered to the terminals marked [+ DC –] (Fig. 1, pg. 2). When servicing the unit, AC mains should be removed.
-
For Access Control applications batteries are optional. When batteries are not used, a loss of AC will result in the loss of output voltage.
When the use of stand-by batteries is desired, they must be lead acid or gel type.
Connect battery to the terminals marked [+ BAT –] (Fig. 1, pg. 2). -
Connect appropriate signaling notification devices to [AC FAIL & BAT FAIL] (Fig. 1, pg. 2) supervisory relay outputs.
Note : When used in fire alarm, burglar alarm or access control applications, “AC Fail” relay must be used to provide a visual
indication of AC power on.
Maintenance:
Unit should be tested at least once a year for the proper operation as
follows:
Output Voltage Test: Under normal load conditions the DC output voltage
should be checked for proper voltage level (refer to Power Supply Voltage
Output Specification chart).
Battery Test: Under normal load conditions check that the battery is
fully charged, check specified voltage both at the battery terminal
and at the board terminals marked [+ BAT –] to ensure that there is no break
in the battery connection wires.
Note : Maximum charging current under discharge is 0.7A.
Note : Expected battery life is 5 years; however, it is recommended
changing batteries in 4 years or less if needed.
LED Diagnostics:
Terminal Identification:
Fig. 1
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone:
718-567-8181 | fax:
718-567-9056
web site: www.altronix.com | e-mail:
info@altronix.com | Lifetime Warranty
IIAL600ULB Rev. 030719
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>