sygonix 2588304 Solar Powered LED Floodlight Instruction Manual

sygonix 2588304 Solar Powered LED Floodlight

Intended use

The product is a solar powered LED floodlight with integrated motion sensor.
The product has an IP65 ingress protection rating and is protected from dust and low pressure water jets from any direction. The product is suitable for outdoor use. Do not submerge the product in water.
If you use the product for purposes other than those described, the product may be damaged. Improper use can result in short circuits, fires, or other hazards.
The product complies with the statutory national and European requirements. For safety and approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product available to third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights reserved.

Delivery contents

• Solar wall light
• Bracket
• 2x wall screws
• 2x plastic dowels
• 2x bracket screws
• 4x small washers
• 2x large washers
• Remote control (batteries not included)
• Operating instructions

Latest product information

Download the latest product information at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.

Description of symbols

The symbol warns of hazards that can lead to personal injury.

The symbol warns of dangerous voltage that can lead to personal injury by electric shock.

This product is constructed according to protection class III.

Safety instructions

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

General

• The product is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
• If you have questions which remain unanswered by this information product, contact our technical support service or other technical personnel.
• Maintenance, modifications and repairs must only be completed by a technician or an authorised repair centre.

Handling

Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.

Operating environment

• Do not place the product under any mechanical stress.
• Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.

Operation

• Consult an expert when in doubt about the operation, safety or connection of the product.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product:
  • is visibly damaged,
  • is no longer working properly,
  • has been stored for extended periods in poor ambient conditions or
  • has been subjected to any serious transport-related stresses.

Li-ion battery

• Never damage the rechargeable battery. Damaging the casing of the rechargeable battery might cause an explosion or a fire!
• Never short-circuit the contacts of the rechargeable battery. Do not throw the battery or the product into fire. There is a danger of fire and explosion!
• Charge the rechargeable battery regularly, even if you do are not using the product. Due to the rechargeable battery technology being used, you do not need to discharge the rechargeable battery first.

LED light

• Do not look directly into the LED light!
• Do not look into the beam directly or with optical instruments!

Drilling

When penetrating the surface (example: drilling or inserting fasteners), make sure no cables or pipes are damaged. Inadvertently penetrating electric cables causes the life-threatening danger of an electric shock! Check for concealed wires and pipes before drilling or inserting fasteners.

Product overview

1. Solar panel
2. Main power / mode button
3. Bracket
4. Motion sensor / indicator light
5. Light angle adjust (at rear)
6. Light panel
7. Light panel tension screws

Remote battery

1. Open the battery compartment.
2. Insert 2x 1.5 V AAA batteries matching polarity as shown inside the compartment.
3. Replace the compartment cover.

Solar recharge battery

Important:
To maximize charging efficiency, keep the solar panel(s) clean and free from debris.

• Solar charge the battery under bright sunlight for at least 7 hours:
  • Before first use
  • After prolonged periods without exposure to sunlight e.g. rain.

Choosing a location

Find a location that exposes the solar module to full sunlight to allow the rechargeable battery to recharge during the day. Consider the following:

• The solar panel should be exposed to maximum sunlight. Do not set up the product in the shade or under any cover.
• Avoid the direct proximity of other light sources such as yard or streetlights, otherwise the product will not switch on automatically at nightfall.
• Avoid locations that are likely to be flooded.

Installation

When tilting the light panel, you may need a hex key to adjust both the tension screws. You can fine tune the lighting angle by:

• Using the angle adjust dial behind the light panel.
• Tilting the light panel.

Attach the bracket

Important:
Adjust the screws on both sides evenly and do not overtighten.

• Insert parts in the order shown.

Freestanding

If placed on the ground, the product should not:

• Obstruct foot traffic.
• Be placed in areas prone to flooding.

Wall mount

• Use the bracket to mark where to drill.
• Insert the included dowels.

Mount the product to the wall by fastening the included screws to the bracket as shown.

The solar panel should face towards the sun. Adjust the bracket and light angle as needed.

Operation

Main unit control

• Press and hold the power / mode button to switch the power ON/OFF.
• Short press the power / mode button to cycle through modes: M1 → M2 → M3.
• The indicator light will flash to indicate which mode has been selected.

Remote control

Preconditions:

Batteries have been inserted.
 You are within line of sight and control range.

1. Press and hold the power / mode button on the product to switch the main power ON.
2. Press any button on the remote to control the product.

Light modes

Note:
“T” mode can only be selected using the remote control.

1500 LM (for 30 sec when motion sensor activated) Motion sensor ON

T| 4x| 1500 LM (max. brightness for 2 hours), then return to previously selected mode until dawn.

Troubleshooting

switch ON/OFF.
The light does not turn on.| The battery power is not suf- ficient to light the product.| Charge the rechargeable battery.
The light stays on for short periods.| Long periods of low sunlight (for example cloudy weather or in winter) will cause the rechargeable battery to re- charge less during the day.| Charge the rechargeable battery.
The light stays on for short periods.| The rechargeable battery is old and cannot store suffi- cient charge.| Have the rechargeable bat- tery replaced by a qualified professional.

Cleaning and care

Important:

– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions. They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.

• To maximize charging efficiency, keep the solar panel(s) clean and free from debris.
• Clean the product with a fibre-free cloth. Moisten if needed.

Disposal

Product

This symbol must appear on any electrical and electronic equipment placed on the EU market. This symbol indicates that this device should not be disposed of as unsorted municipal waste at the end of its service life.

Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separately from unsorted municipal waste. Spent batteries and accumulators, which are not enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-destructive manner, must be removed by end users from the WEEE in a non-destructive manner before it is handed over to a collection point.

Distributors of electrical and electronic equipment are legally obliged to provide free takeback of waste. Conrad provides the following return options free of charge (more details on our website):

• in our Conrad offices
• at the Conrad collection points
• at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG

End users are responsible for deleting personal data from the WEEE to be disposed of. It should be noted that different obligations about the return or recycling of WEEE may apply in countries outside of Germany

(Rechargeable) batteries

Remove batteries/rechargeable batteries, if any, and dispose of them separately from the product. According to the Battery Directive, end users are legally obliged to return all spent batteries/rechargeable batteries; they must not be disposed of in the normal household waste.

Batteries/rechargeable batteries containing hazardous substances are labelled with this symbol to indicate that disposal in household waste is forbidden. The abbreviations for heavy metals in batteries are: Cd = Cadmium, Hg = Mercury, Pb = Lead (name on (rechargeable) batteries, e.g. below the trash icon on the left).

Used (rechargeable) batteries can be returned to collection points in your municipality, our stores or wherever (rechargeable) batteries are sold. You thus fulfil your statutory obligations and contribute to environmental protection.

Batteries/rechargeable batteries that are disposed of should be protected against short circuit and their exposed terminals should be covered completely with insulating tape before disposal. Even empty batteries/rechargeable batteries can contain residual energy that may cause them to swell, burst, catch fire or explode in the event of a short circuit.

Technical data

Rechargeable battery … 10000 mAh (5 x 3.7 V 2000 mAh), Li-Ion
Battery recharge …. 7 hrs (bright sunlight)
Light runtime…….. max. 10 hrs
Remote control …. batteries: 2x AAA 1.5 V (not included) range: approx. 10 m
Protection class … III
Ingress protection…… IP65
LED……. 60 pcs SMD2835
max. 15 W
Colour temperature……. 5700 K
Brightness (max.) … 1500 LM
Brightness / modes……. M1: 1500 LM (first 5 hours), 300 LM (until dawn) / motion sensor OFF M2: 900 LM (until dawn) / motion sensor OFF M3: 300 LM (until dawn), 1500 LM (for 30 sec when motion sensor activated) / motion sensor ON T: 1500 LM (max. brightness for 2 hours), then return to previously selected mode (until dawn)
Illuminance …. activation thresholds: ON (20 to 40 lux), OFF (80 to
120 lux)
PIR sensor…….. range: max. 6 m
angle: 120°
Solar panel … 7 W, poly-crystalline
Operating conditions…….. -20 to +45 °C
Storage conditions…….. -20 to +60 °C
Dimensions (L x W x H)… 296 x 56.4 x 324.5 mm
Weight ….. 2.3 kg

CUSTOMER SUPPORT

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirsch au (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2588304_V5_0223_dh_mh_en 9007199856675083-2 I2/O5 en

References

• Conrad Electronic » All parts of success
• Conrad Electronic » All parts of success
• Download center

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>