LG MB3021 Bluetooth 5.1 Smart Device Module User Manual
- June 9, 2024
- LG
Table of Contents
Bluetooth 5.1 Smart Device Module
User Manual
MB3021 Bluetooth 5.1 Smart Device Module
Module : MB3021
MB3021 is a fully integrated Bluetooth module. It is based on Qualcomm’s
QCC3021 chip with specific interface design to meet Customer’s needs.
MB3021 is compatible with Bluetooth specification version 5.1. It integrates
RF, Baseband controller, etc., a completed Bluetooth subsystem.
Module Specification
Chips | QCC3021 |
---|---|
Bluetooth Spec | Bluetooth 5.1 |
Frequency Band | 2402 ~ 2480 MHz |
Tx Power | 2.51mW ~ 6.31mW (Bluetooth Power Class I) |
Rx Sensitivity | < -70dBm (BER 0.1%) |
Distance | < 100m (Open Space) |
Power Voltage | 3.3V |
Dimension | 20.0ⅹ33.0 ⅹ3.0 mm |
Environmental Range | Operation temperature : -30 ~ +80℃ |
Modulation | GFSK, π/4-DQPSK, 8DPSK |
Communication Method | FHSS |
Block Diagram
Pin Define
No | Pin Name | I/O | Reset State | Description |
---|---|---|---|---|
1 | GND | I | GND CONNECTION FOR INTERNAL DIGITAL CIRCUITTRY AND PADS | |
2 | GND | I | GND CONNECTION FOR INTERNAL DIGITAL CIRCUITTRY AND PADS | |
3 | GND | I | GND CONNECTION FOR INTERNAL DIGITAL CIRCUITTRY AND PADS | |
4 | PIO[21] | I/O | Pull-down | GPIO |
5 | TEST | I | Pull-down | Must be connected to ground |
6 | I2S_SDIN | I/O | Pull-down | SYNCHRONOUS DATA INPUT , Alternative |
function PIO[19]
7| I2S_SDOUT| I/O| Pull-down| SYNCHRONOUS DATA OUTPUT, Alternative
function PIO[18]
8| I2S_WS| I/O| Pull-down| SYNCHRONOUS DATA SYNC , Alternative function
PIO[17]
9| I2S_SCLK| I/O| Pull-down| SYNCHRONOUS DATA CLOCK, Alternative
function PIO[16]
10| PIO[15]| I/O| Pull-down| Alternative function MCLK_OUT
11| USB_DN| I/O| | USB DATA MINUS
12| USB_DP| I/O| | USB DATA PLUS
13| 1V8_SMPS| O| | 1.8V REGULATOR OUTPUT
14| VCHG_SENSE| I| | CHARGER INPUT SENSE PIN
15| CHG_EXT| I| | EXTERNAL BATTERY CHARGER CONTROL
16| VBAT_SENSE| I| | BATTERY CHARGER SENSE INPUT
17| 3V3_OUT| O| | ALTERMATIVE SUPPLY VIA BYPASS REGULATOR FOR 1.8V AND
1.35V REGULATOR INPUTS. MUSET BE THE SAME POTENTIAL AS VBAT.
18| GND| I| | GND CONNECTION FOR INTERNAL DIGITAL CIRCUITTRY AND PADS
19| LED[0]| O| | General-purpose analog/digital input or open drain LED
output.
20| LED[1]| O| | General-purpose analog/digital input or open drain LED
output.
21| LED[2]| O| | General-purpose analog/digital input or open drain LED
output.
22| SYS_CTRL| I| Pull-down| REGULATOR ENABLE INPUT
23| VBAT| I| | BATTERY POSITIVE TERMINAL
24| VBUS| I| | BATTERY CHARGER INPUT
25| VDD_PADS| I| | 1.7~3.6V SUPPLY INPUT FOR IO PORTS
26| LED[5]| O| | General-purpose analog/digital input or open drain LED
output.
---|---|---|---|---
27| NRESET| I| Pull-up| RESET IF LOW (>5ms)
28| UART_TX| O| Pull-down| UART DATA OUT, Alternative function PIO[22]
29| UART_RX| I| Pull-down| UART DATA IN, Alternative function PIO[23]
30| GND| I| | GND CONNECTION FOR INTERNAL DIGITAL CIRCUITTRY AND PADS
31| PIO[4]| I/O| | PIO[4], Alternative function UART Request to Send
32| PIO[3]| I/O| | PIO[3], Alternative function UART Clear to Send
33| PIO[6]| I/O| | GPIO, Alternative function TBR_MOSI[0]
34| PIO[7]| I/O| Pull-up| GPIO, Alternative function TBR_MISO[0]
35| PIO[8]| I/O| Pull-down| GPIO, Alternative function TBR_CLK
36| PIO[5]| I/O| Pull-down| GPIO
37| PIO[2]| I/O| Pull-down| GPIO
38| AOUT_RP| O| | SPEAKER OUTPUT POSITIVE RIGHT
39| AOUT_RN| O| | SPEAKER OUTPUT NEGATIVE RIGHT
40| AOUT_LN| O| | SPEAKER OUTPUT NEGATIVE LEFT
41| AOUT_LP| O| | SPEAKER OUTPUT POSITIVE LEFT
42| GND| I| | GND CONNECTION FOR INTERNAL DIGITAL CIRCUITTRY AND PADS
43| MIC_BIAS| O| | MIC BIAS OUTPUT
44| MIC_LN| I| | MIC INPUT NEGATIVE LEFT
45| MIC_LP| I| | MIC INPUT POSITIVIE LEFT
46| MIC_RN| I| | MIC INPUT NEGATIVE RIGHT
47| MIC_RP| I| | MIC INPUT POSITIVIE RIGHT
48| GND| I| | GND CONNECTION FOR INTERNAL DIGITAL CIRCUITTRY AND PADS
Mechanical Dimension
TOP VIEW
Mark | Dimension | Mark | Dimension | Mark | Dimension | Mark | Dimension |
---|---|---|---|---|---|---|---|
A | 33.0±0.3 | D | 3.4±0.3 | G | 0.8±0.15 | J | 10.2±0.3 |
B | 20.0±0.3 | E | 13.2±0.3 | H | 0.4±0.15 | K | 1.0±0.3 |
C | 20.4±0.3 | F | 2.4±0.3 | I | 1.2±0.15 | L | 3.0±0.3 |
Module PCB coplanarity measured from seating plane ≤ 0.1 mm
Electrical Characteristics
Conditions: VDD = 3.3V, Ta = 25 ℃, unless otherwise noted.
Absolute Maximum Ratings
Parameter | Min | Max | Unit |
---|---|---|---|
Power Supply Voltage : VBAT | -0.4V | 4.8V | DCV |
Power Supply Voltage : VBUS | -0.4V | 7.0V | DCV |
Power Supply Voltage : VDD PADS | -0.4V | 3.8V | DCV |
Storage Temperature | -40 | 85 | ℃ |
Recommended Operating Conditions
Parameter | Min | Max | Unit |
---|---|---|---|
Power Supply Voltage : VBAT | 3.0V | 4.6V | DCV |
Power Supply Voltage : VBUS | 4.75V | 5.5V | DCV |
Power Supply Voltage : VDD PADS | 3.0V | 3.6V | DCV |
Operation Temperature | -30 | 80 | ℃ |
Current consumption
Parameter | Connection Type | Avg | Peak | Unit |
---|---|---|---|---|
Page scan, Time interval = 1.28s | – | <1 | 1 | mA |
Inquiry and Page scan, Time interval = 1.28s | – | <1 | 1 | mA |
ACL No data transfer | Master | 1.5 | 2 | mA |
ACL data transfer | Master | 17 | 43 | mA |
Input/Output Characteristics
Parameter | Min | Max | Unit |
---|---|---|---|
VIL Input Voltage Low | -0.4 | 0.8 | V |
VIH Input Voltage High | 0.7*VDD | VDD+0.4 | V |
VOL Output Voltage Low | – | 0.2 | V |
VOH Output Voltage High | VDD-0.2 | – | V |
General Performance
Parameter| Condition| Min| Typ| Max| Unit
Frequency Range| Normal| 2402| –| 2480| MHz
Transmitter Performance
Parameter| Condition| Min| Avg| Max| Unit
Transmit Power| Normal| 4| –| 10| dBm
Parameter| Condition| Min| Typ| Max| Unit
Power density| Normal| –| –| <20| dBm
20dB bandwidth| Normal| | | 1000| KHz
Adjacent channel power (F0 = 2441MHz)| F=F0 ±2MHz| –| –| -20| dBm
F=F0 ±3MHz| –| –| -40| dBm
F=F0 ±4MHz| –| –| -40| dBm
Out-band Spurious Emission| 30MHz ~ 1GHz| –| –| -36| dBm
1GHz ~ 12.75GHz| –| –| -30| dBm
1.8GHz ~ 1.9GHz| –| –| -47| dBm
5.1GHz ~ 5.3GHz| –| –| -47| dBm
** Modulation Characteristic| ∆F1avg| 140| –| 175| KHz
∆F2max| 115| –| –| KHz
∆F2avg / ∆F1avg| 80| –| –| %
Initial Carrier Frequency Tolerance| DH1 packet| -75| –| 75| KHz
Carrier Frequency Drift| DH5 packet| -25| | 25| KHz
Receiver Performance**
Parameter| Condition| Min| Type| Max| Unit
Sensitivity at 0.1% BER| Single slot (DH1 packet)| –| –| -70| dBm
Sensitivity at 0.1% BER| Multi slot (DH5 packet)| –| –| -70| dBm
Maximum received signal at 0.1% BER| | -20| –| –| dBm
Maximum level of intermodulation interferers| f1-f2 = 5 MHz, Pwanted= -64 dBm|
-39| –| –| dBm
Regulatory Statement (FCC)
-
Part 15.19 Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. -
Part 15.105 Statement (Class B)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
-
Part 15.21 Statement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device must not be co-located or operating in conjunction with any other antenna or transmitter. -
Responsible Party Information (Supplier’s Declaration of Conformity)
LG Electronics USA
1000 Sylvan Avenue Englewood Cliffs
New Jersey, United States, 07632
Regulatory notice to host manufacturer according to KDB 996369 D03 OEM
Manual v01
List of applicable FCC rules
This module has been granted modular approval as below listed FCC rule parts.
- FCC Rule parts 15C(15.247)
Summarize the specific operational use conditions
The OEM integrator should use equivalent antennas which is the same type and
equal or less gain then an antenna listed in this instruction manual.
RF exposure considerations
The module has been certified for integration into products only by OEM
integrators under the following condition:
- The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
- The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
- Mobile use
As long as the three conditions above are met, further transmitter testing
will not be required.
OEM integrators should provide the minimum separation distance to end users in
their end-product manuals.
-
Antennas list
This module is certified with the following integrated antenna.- Type: PCB Trace Antenna
- Max. peak Antenna gain
BT Ant: 2.90 dBi (2402 – 2480 MHz)
Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.1043 as permissive change procedure.
-
Label and compliance information
-
End Product Labeling
The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:
• Contains FCC ID: BEJ-MB3021
• BEContains IC: 2703H-MB3021 -
Information on test modes and additional testing requirements
OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed (for example, digital device
emissions, PC peripheral requirements, additional transmitter in the host, etc.). -
Additional testing, Part 15 Subpart B disclaimer
The final host product also requires Part 15 subpart B compliance testing with the modular transmitter installed to be properly authorized for operation as a Part 15 digital device.
RSS-GEN, Sec. 7.1.3–(licence-exempt radio apparatus)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation
is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
CE Statement
RF Exposure
The antenna (or antennas) must be installed so as to maintain at all times a
distance minimum of at least 20 cm between the radiation source (antenna) and
any individual.
This device may not be installed or used in conjunction with any other antenna
or transmitter
Simplified Declaration of Conformity (CE / UK)
Hereby, LG Electronics declares that hat MB3021 is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address:
http://www.lg.com/global/support/cedoc/cedoc#
Hereby, [LG Electronics Inc.]. declares that MB3021 is in compliance with the
Radio Equipment Regulations 2017. The full text of the UK declaration of
conformity is available at the following internet address:
http://www.lg.com/global/support/cedoc/
cedoc#
This restriction will be applied in all member states.
The postal address: LG Electronics European Shared Service Center B.V.
Krijgsman 1, 1186 DM Amstelveen, The Netherlands
UK Importer: LG Electronics U.K. Ltd
The postal Address: Velocity 2, Brooklands Drive, Weybridge, KT13 0SL
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>