HAYWARD HP55TR Trevinium Swimming Pool Heat Pump Unit Instruction Manual

REV 2017-1
TREVINIUM by Hayward
SWIMMING POOL HEAT PUMP UNIT
Installation & Instruction Manual  Model
HP55TR HP7STR

USER INTERFACE

General presentation
The heat pump is equipped with a digital control panel with a touch screen, electronically connected and pre-set at the factory in heating mode.

Legend

OFF Mode
When the heating pump is in sleep mode (OFF Mode) “OFF” is displayed on the command screen.

ON Mode
When the heating pump is running or regulating (ON Mode), the inlet and outlet water temperatures are displayed on the command screen.

At the end of a setting, press to validate.
The settings will be automatically saved if no button is pressed during 20s.

Clock settings
If the display is in standby mode, press briefly on .

1. Press to bring up the symbol .
2. Press to make the time display flash. Set the hour using the buttons
3. Press then set the minutes with the buttons .
4. Press to validate.

Timer function settings
Setting this function is necessary if you would like to run the heat pump for a shorter period than what is defined by the filtration clock. Therefore, you can program a deferred start and an anticipated stop or simply stop a certain timeframe from running (at night, for example).
It is possible to set 2 Start Timers (ON1 et ON2) and 2 Stop Timers (OFF1 et OFF2).

Timer 1 setting – Start

1. Press for 2s, Timer ON1 1 flashes (*).
2. Press to set the hours with the buttons .
3. Press to set the minutes with the buttons .
4. Press to validate.

Timer 1 setting – Stop

1. Press for 2s, Timer ON1 1flashes (*).
   Press once, Timer OFF1 flashes.

2. Press to set the hours with the buttons .

3. Press to set the minutes with the buttons .

4. Press to validate.

(*) To access Timer ON2 2directly, press for 2s, then press twice.

Timer 2 settings
After the Timer 1 settings, you will access directly the settings for Timer 2: 2 and 2.
Proceed in the same manner as for Timer 1.
Nota: To access directly Timer ON2 2, press for 2s, then press twice on .

Timers suppression (Start and Stop)

1. Press for 2s, Timer ON1 1 flashes.(*)

2. Press to make the time display flash.

3. Press to suppress the Timer 1.

4. Press to validate.

5. Press for 2s, the Timer 1 flashes.
   Press once , the Timer 1 flashes.(*)

6. Press to make the time display flash.

7. Press to suppress the Timer 1.

(*) To access Timers 2 2 or 2. , follow steps 1) or 4) then press twice . Proceed in the same manner as above.

Operation mode selection: cooling, heating or automatic
In Mode “OFF” or “ON”
Press the button to change mode: cooling, heating or automatic.

If the heat pump is set in heating only or cooling only, changing mode is not possible.

Setting and visualisation of the set point (desired water temperature)
If the button is not visible on the screen, press briefly. (While operating or stopped, simply press the button to view the set point)

In Mode “OFF” or Mode “ON”
Press the button to display the set point, then press or to set the set point you wish.
The setting is made with a precision of 0.5 °C.

It is recommended to never exceed 30°C to avoid alteration of the liners.
Press the button for 5 s until it beeps and this symbol appears .
To unlock, press for 5 s until it beeps and this symbol disappears .

6.3  Exploded View- HP55TR

6.3 Spare Parts List -HP55TR

6.3 Exploded view – HP75TR

6.3 Spare parts list HP75TR

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>