Hunter 19062 6 Light Chandelier Instruction Manual
- June 4, 2024
- Hunter
Table of Contents
Hunter 19062 6 Light Chandelier
PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the
circuit breaker and completely remove the old fixture from the ceiling,
including the old mounting bracket. Remove the new mounting bracket assembly
from the bag. One end of the threaded post (F) should be attached to the
mounting bracket (A) with a washer (D) and a hex nut (E) in place. The other
end should have the canopy loop (G) attached. Unscrew the canopy loop ring (I)
from the canopy loop (G). Depending on the placement of your junction box the
position of threaded post (F) may need to be adjusted to allow the canopy to
be flush with the ceiling. Determine this by lifting mounting bracket (A) up
to the junction box and place canopy (H) over the canopy loop (G), so that it
is flush with the ceiling. Adjust the position of threaded post (F) on the
mounting bracket (A) so that the canopy (H) covers at least half of the
exterior threads on the canopy loop (G) while it is securely connected to
threaded post (F). The threaded post (F) can be adjusted by loosening hex nut
(E) to allow movement of threaded post (F) on mounting bracket
(A). Once the ideal position of the threaded post (F) is determined, tighten
up the hex nut (E) onto the threaded post (F) just beneath the mounting
bracket (A) to secure the threaded post in place.
ASSEMBLING THE FIXTURE
Thread the wires through and attach the center rod (O) to the hexagon nut (P)
of the fixture, then slide the rod cover (N) and lock ring (M) onto the center
rod (O) and secure with the hanging ring (L). By measuring, determine the
correct number of chain links needed for proper hanging height. If necessary,
use a pair of pliers to open and remove any excess chain. Attach one quick-
connect link (J) to each end of chain (K). Use one quick-connect link (J) to
attach chain (K) to hanging ring (L) and securely close. Feed the fixture
wires up through the chain (every three links or so) pulling the wires until
taut. Slide canopy loop ring (I) and canopy (H) onto the chain/wire. Use the
remaining quick-connect link (J) to attach chain (K) to canopy loop (G) and
thread the wires through. To shorten the fixture, trim the wires to desired
length. Leave at least 8 to 10 inches of wire in addition to the desired
length. Have a helper support the fixture’s weight and attach the mounting
bracket (A) to the junction box by securely tightening the mounting screws
(B).
CONNECTING THE WIRES
Have a helper support the fixture’s weight while completing the wiring. Attach
the fixtures wires to the power supply wires from the junction box. Connect
black to black (Live); white to white (grounded); grounding to grounding
(green or copper). Twist the ends of the wire pairs together. Then, twist on a
wire connector. Make sure all twists are in the same direction. Loop fixture’s
ground wire around grounding screw (C) and tighten. If there is no ground wire
(green or copper) from the junction box, contact a qualified electrician.
FINISHING THE INSTALLATION
Place the canopy (H) flush to the ceiling and slide the canopy loop ring (I)
up beneath the canopy. Tightly screw canopy loop ring (I) onto the canopy loop
(G) to properly secure the canopy (H) in place. Install light bulb (not
included) in accordance with the fixture’s specifications. Do not exceed the
recommended wattage. Secure glass (S) onto the socket (Q) with screws (R).
Your installation is now complete. Turn on the power and test.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep
cleaning. For regular cleaning, turn off the light and wipe down the fixture
with a clean lint-free cotton or microfiber cloth. Never spray cleaner
directly onto the fixture.
Hunter Pro Tip:
Let the tool do the work! Use chain pliers to easily open and close chain
links to shorten your fixture.
Hunter Pro Tip:
Twist or tape wire ends together to make it easier to pass them through the
downrods. Threaded post may also be removed for easier wire access.
Here are the tools you’ll need to complete your installation:
Fixture weight ±2 lbbs:
Peso ±2 lb:
Poids fixe ±2 lbs:
Hardware Service Kit
Part Model Finish
- KG20802214 19062 19064 Brushed Nickel
- KG2080183419120 19388 Noble Bronze
WARNING
- All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.
- To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
- The lighting fixture must be grounded. If the ground wire for the installation site is not present immediately STOP installation and consult a qualified electrician.
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that
they are read carefully and completely before beginning installation of the
lighting fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>