Vanguard VEO 2S AM-264TR Monopod with Tri-Feet and Smartphone Connector User Manual

Vanguard VEO 2S AM-264TR Monopod with Tri-Feet and Smartphone Connector

Thank you for purchasing this VEO 25 Monopod.

PART DESCRIPTION

1. A : 1/4″Camera Screw
2. B : Stop Screws
3. C : Rubber Protection Cap
4. D : Locking Disc
5. E : Karabiner
6. F : Plastic Buckle
7. G : Wrist Strap
8. H : Twist Lock
9. I : Locking Ring
10. J : Clawed Feet
11. K : TPR Grip
12. L : Leg
13. M : Extendable Top Clamp of the Smart Phone Holder
14. N : Smart Phone Holder Support Stand

INSTALLATION INSTRUCTIONS

ATTACHING YOUR CAMERA OR OTHER EQUIPMENT

1. Step 1 : Line up the screw (Al to the camera or other equipment and connect to the monopod.
2. Step 2 :Turn the locking disc until secured firmly.

ATTACHING & REMOVING THE HEAD

A 3mm hex wrench (included) can be used to either attach or remove the head using the three stop screws (B) in the base of the locking disc (D). Assembling the head:

1. Step 1 : Confirm the stop screws (B) are not interfering.
2. Step 2 : Connect the monopod to the head by turning the head clockwise until secured firmly.
3. Step 3 : Use the hex wrench to tighten stop screws (BJ by turning clockwise.

Note: Before use, please confirm the stop screws (B) are locked. Removing the head:

1. Step 1 : Use the hex wrench to release stop screws (Bl by turning counterclockwise.
2. Step 2 : Confirm head panning knob is locked, then turn the head counterclockwise.

LEG EXTENSION

To adjust the height of the leg, each telescopic section can be extended by releasing the twist lock (H).
Always start from top to bottom (thinnest section last) to reach the desired height. Extending & using the larger leg section first will ensure your monopod stability.

1. Step 1 : Release the leg sections successively by turning clockwise (H). The Advanced twist-lock features 1/2 turn lock/unlock system.
   Then extend leg section.

2. Step 2 : Lock the twist locks (H) by turning counterclockwise until fully tightened.

3. Step 3 : Make sure all locks (H) are perfectly tightened to avoid equipment damages.

WRIST STRAP ADJUSTMENT
Adjust the wrist strap (G) by sliding the plastic buckle (F).

USING KARABINER
The karabiner (El can be attached to waist belt or bag hook.

TRI-STAND OPERATIONAL GUIDELINES

Open the three clawed feet (J) in order, as shown  Fold hand support arm claw (J), after the first light downward pull outward, reverse (JJ as shown

Warning : You must first pull out (J) then lift upward.

The feet cannot be lifted upward without pulling out first, doing so will damage or break the mechanism.

ANGLE ADJUSTMENT SYSTEM

VEO 25 monopod is fitted with a dual fix to multi angle adjustment system (I) positioned between the monopod and the tri-stand as shown (fig. 9).
Open the three clawed feet (J) first. Turn locking ring (I) counterclockwise to tilt monopod. This operation allows multi-angle shooting, as shown (fig. 9). The locking ring can be turned back clockwise to block the ball located in the base. This offers vertical fixed angle, as shown in (fig. 9).

Warning : We recommend that you install your equipment afterwards. Don’t let a monopod stand upright by itself, always keep it in your grip.

USING THE SMART PHONE HOLDER

The smart phone holder can be used in various ways as specified below: Connect the smart phone holder directly to the monopod. Smart phone holder is compatible with models up to 87mm wide. Using the smart phone holder simply extend the top clamp (M) and place the smart phone in the holder. Release (M) and make sure the smart phone is securely held in place.

Notes before use:

1. Always comply with the weight restrictions. Exceeding the maximum load capacity may cause damage to equipment or personal injury.
2. Ensure all individual knobs and locks are securely tightened to avoid movement, as movement may result in equipment damage or personal injury.
3. Carefully hold camera equipment stable when removing it from the monopod.
4. Carrying your monopod:
5. a ) After use, please remove the camera and we recommend you fold the monopod completely.
6. b ) DO NOT carry the monopod when the camera is still mounted.
7. Cleaning your monopod:
8. a ) When necessary, wipe the monopod with a soft cloth and if required use mild detergent.
   b ) When used around salt water, first rinse with clean water, then wipe with a dry soft cloth.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>