KARCHER HD 4/9 P, HD 5/11 P Pressure Washers User Manual
- June 9, 2024
- Karcher
Table of Contents
- HD 4/9 P, HD 5/11 P Pressure Washers
- Device elements
- Safety instructions
- Proper use
- Safety Devices
- Environmental protection
- Before Startup
- Start up
- Operation
- Transport
- Storage
- Care and maintenance
- Troubleshooting
- Accessories and Spare Parts
- Warranty
- EU Declaration of Conformity
- Technical specifications
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Makes a different
HD 4/9 P
HD 5/11 P
Pressure Washers
User Manual
HD 4/9 P, HD 5/11 P Pressure Washers
Please read and comply with these original instructions prior to the initial operation of your appliance and store them for later use or subsequent owners.
Device elements
Please unfold the front picture side
1. Union joint
2. Nozzle
3. Spray lance EASY!Lock
4. Trigger gun EASY!Lock
5. Safety catch
6. Triggering lever
7. Safety lever
8. High pressure hose EASY!Lock
9. Push handle, top (extended)
10. Push handle, bottom (slid in)
11. Holder for storage of a nozzle with screw connection or a surface
cleaner
12. Nozzle rack for triple nozzle
13. Recessed grip
14. Nameplate| 15. Skid
16. High-pressure connection EASY!Lock
17. Wheel
18. Nozzle rack for rotor nozzle (rotor nozzle is only included in the scope
of
delivery with model HD…Plus)
19. Spray lance holder with clamping, for transportation
20. Sieve
21. Water connection
22. Quiver for spray lance
23. Power switch
24. Cable clamp
25. Carrying handle
26. Spray lance holder without clamping
27. Rubber band
28. Storage compartment for hoses
---|---
not included in the scope of delivery
Colour coding**
– The operating elements for the cleaning process are yellow.
Safety instructions
– Before first start-up it is definitely necessary to read the operating
instructions and safety indications Nr. 5.951949.0!
– Please follow the national rules and regulations for fluid spray jets of the
respective country.
– Please follow the national rules and regulations for accident prevention of
the respective country. Fluid spray jets must be tested regularly and the
results of these tests must be documented in writing.
– The appliance/accessories must not be modified.
Hazard levels
DANGER
Pointer to immediate danger, which leads to severe injuries or death.
WARNING
Pointer to a possibly dangerous situation, which can lead to severe injuries
or death.
CAUTION
Pointer to a possibly dangerous situation, which can lead to minor injuries.
ATTENTION
Pointer to a possibly dangerous situation, which can lead to property damage.
Symbols on the machine
High-pressure jets can be dangerous if improperly used. The jet may not be
directed at persons, animals, live electrical equipment or at the appliance
itself.
According to applicable regulations, the appliance must never be used on the
drinking water net without a system separator. A suitable system separator by
KÄRCHER or alternatively a system separator according to EN 12729 type BA must
be used. Water that was flowing through a system separator is considered non-
drinkable.
Proper use
Use this high pressure cleaner exclusively for
– for cleaning with high-pressure jet (e.g. cleaning of facades, terraces,
gardening tools).
With optional accessories detergent can be added.
For stubborn soiling we recommend the use of a rotor nozzle (only included in
the scope of delivery with model HD…Plus)
Quality requirements for water:
ATTENTION
Only clean water may be used as high pressure medium. Impurities will lead to
increased wear and tear or formation of deposits in the appliance.
If recycled water is used, the following limit values must not be exceeded.
pH value | 6,5…9,5 |
---|---|
electrical conductivity * | Conductivity fresh water +1200 μS/cm |
settle able solids ** | < 0,5 mg/l |
total suspended solids *** | < 50 mg/l |
Hydrocarbons | < 20 mg/l |
Chloride | < 300 mg/l |
Sulphate | < 240 mg/l |
Calcium | < 200 mg/l |
Total hardness | < 28 °dH |
< 50 °TH
< 500 ppm (mg CaCO3/l)
Iron| < 0,5 mg/l
---|---
Manganese| < 0,05 mg/l
Copper| < 2 mg/l
Active chloride| < 0,3 mg/l
free of bad odours
- Maximum total 2000 μS/cm
** Test volume 1 l, settling time 30 min
*** no abrasive substances
Safety Devices
Safety devices serve for the protection of the user and must not be put out of
operation or bypassed with respect to their function.
Pressure switch
If the pulling lever on the trigger gun is released the pressure switch turns
off the pump, the high-pressure jet is stopped. If the pulling lever is pulled
the pump is turned on again.
Environmental protection
****| The packaging material can be recycled. Please do not throw the
packaging material into household waste; please send it for recycling.
---|---
| Old appliances contain valuable materials that can be recycled; these
should be sent for recycling. Batteries, oil, and similar substances must not
enter the environment. Please dispose of your old appliances using appropriate
collection
systems.
Electrical and electronic devices often contain components which could
potentially pose a danger to human health and the environment if handled or
disposed of incorrectly. However, these components are necessary for the
proper operation of the device. Devices marked with this symbol must not be
disposed of with regular household rubbish.
Notes about the ingredients (REACH)
You will find current information about the ingredients at:
www.kaercher.com/REACH
Before Startup
Attaching the Accessories
Note: The EASY!Lock system joins components with a quick-fasten thread
solidly and securely with just one turn.
⇒ Insert the high pressure nozzle onto the spray lance.
⇒ Install union nut and hand-tighten it (EASY!Lock).
⇒ Join the spray lance with the trigger gun and tighten until hand-tight
(EASY!Lock).
⇒ Join the high-pressure hose with trigger gun and high-pressure connection of
the appliance and tighten until handtight (EASY!Lock).
Start up
WARNING
Risk of injury! Appliance, accessories, supply lines and connections must be
in fault free condition. If they are not in a perfect state then the appliance
must not be used.
Electrical connection
DANGER
Danger of injury by electric shock.
– It is imperative to connect the appliance to the electric mains by means of
a plug. It is forbidden to permanently connect the appliance to the power
supply. The plug serves for the disconnection from the mains.
– The plug and coupling of the extension cable used must be watertight.
– Use an extension cable with protective earth conductor (protection class 1)
and an adequate cross section (see “Technical data”) und fully uncoil it from
the cable drum.
For connection values, see type plate/technical data.
⇒ Unwind the mains cable and place it on the floor.
⇒ Insert the mains plug into a socket.
Water connection
Connection to the water supply
WARNING
Observe regulations of water supplier.
According to applicable regulations, the appliance must never be used on the
drinking water net without a system separator. A suitable system separator by
KÄRCHER or alternatively a system separator according to EN 12729 type BA must
be used.
Water that was flowing through a system separator is considered non-drinkable.
CAUTION
Always connect the system separator to the water supply, never directly to
the appliance! For connection values refer to technical specifications
⇒ Connect the supply hose (min. length 7.5 m, minimum diameter 1/2“) to the
water connection point of the machine and at the water supply point (for e.g.
a tap).
Note:
The supply hose is not included.
⇒ Open the water supply.
Drawing in water from open reservoirs
⇒ Screw the suction hose with filter (optional accessory) to the water
connection.
⇒ Appliance ventilation:
Unscrew the nozzle from the spray lance.
Switch on the appliance and let it run until the water exiting is bubble-free.
Let the appliance run for 10 seconds – then switch off the appliance switch.
Repeat the procedure several times.
⇒ Switch off the appliance and fit the nozzle again.
Operation
DANGER
Risk of explosion!
Do not spray flammable liquids.
If the appliance is used in hazardous areas (e.g. filling stations) the
corresponding safety regulations must be observed.
Risk of injury! Hold the hand spray gun and the spray pipe firmly with both
hands. Risk of injury! The trigger and safety lever may not be locked during
the operation.
Risk of injury! Contact Customer Service if the safety lever is damaged.
Risk of injury from high-pressure water jet.
Slide the safety catch on the trigger gun forward before performing any work
with the appliance.
CAUTION
Environmental damage. Clean motors at places with a corresponding oil
separator only.
Opening/closing the trigger gun
⇒ To open the trigger gun: Actuate the safety lever and trigger.
⇒ To close the hand spray gun: Release the safety lever and trigger.
Operation
The appliance can be operated in a vertical or horizontal position.
Note:
The appliance is equipped with a pressure switch. The motor starts up only
when the trigger gun is open.
⇒ Set the appliance switch to “I”.
⇒ Release the trigger gun. To do so, push the safety catch towards the back.
⇒ Open the hand spray gun.
Interrupting operation
⇒ Close the hand spray gun.
The appliance switches off.
⇒ Secure the trigger gun. To do so, push the safety catch towards the front.
After the interruption:
⇒ Release the trigger gun. To do so, push the safety catch towards the back.
⇒ Open the hand spray gun.
The appliance will switch on again.
Turn off the appliance
⇒ Shut off water supply.
⇒ Open the hand spray gun.
⇒ Switch on the pump with the power switch and allow to run for about 5-10
seconds.
⇒ Close the hand spray gun.
⇒ Set the appliance switch to “0/OFF“.
⇒ Pull main plug out of socket with dry hands only.
⇒ Remove water connection.
⇒ Activate hand spray gun until device is pressure less.
⇒ Secure the trigger gun. To do so, push the safety catch towards the front.
Storing the Appliance
⇒ Place the spray lance with the trigger gun into the quiver for the spray
lance and snap it into place in the spray lance holder.
⇒ Wind the connection cable around the cable holder.
⇒ Fasten the plug with the mounted clip.
⇒ Slide in push handle.
⇒ Wind up the high-pressure hose and hang it over the hose storage.
Frost protection
ATTENTION
Frost will destroy the not completely water drained device.
Store the appliance in a frost free area.
If you cannot store it in a frost-free place:
⇒ Drain water.
⇒ Pump in conventional frost protection agents through the appliance.
Note:
Use normal glycol-based anti-freezing agents for automobiles.
Observe handling instructions of the antifreeze agent manufacturer.
⇒ Operate device for max. 1 minute until the pump and conduits are empty.
Transport
CAUTION
Risk of injury and damage! Observe the weight of the appliance when you
transport it.
ATTENTION
Protect the trigger from damage during transport.
⇒ Hold the appliance at the carrying handle and the recessed grip for carrying
it.
⇒ When transporting in vehicles, secure the appliance according to the
guidelines from slipping and tipping over.
⇒ For transport over longer distances, pull out the push handle to the end
position and drag the appliance behind you holding the push handle.
⇒ In order to climb stairs, pull the appliance up step by step. The skids
protect the casing from damage.
Holder for surface cleaner
⇒ Attach the connecting piece of the surface cleaner to the holder on the
high-pressure cleaner.
⇒ Screw union nut.
Transport by crane
⇒ Attach the lifting device to the carrying handle of the appliance.
Safety information about cranes
DANGER
Risk of injury due to machine dropping.
– Adhere to the local accident prevention guidelines and safety notes.
– Check the carrying handle for damage prior to every transportation by crane.
– Check the lifting unit for damage prior to each transport by crane.
– Only lift the appliance using the carrying handle.
– Do not use stop chains.
– Protect the lifting device from inadvertent load release.
– Remove spray lance with trigger gun, nozzles, surface cleaner and other
loose objects prior to transportation by crane.
– Do not transport any articles on the appliance during the lifting process.
– The appliance must only be transported by properly trained crane personnel.
– Do stand below the load.
– Ensure that no persons are present in the immediate vicinity of the crane.
– Do not leave the appliance on the crane unattended.
Storage
CAUTION
Risk of injury and damage! Note the weight of the appliance in case of
storage.
This appliance must only be stored in interior rooms.
Care and maintenance
DANGER
Risk of injury by inadvertent startup of appliance and electrical shock.
First pull out the plug from the mains before carrying out any tasks on the
machine.
Safety inspection/ maintenance contract
You can sign with your dealer a contract for regular safety inspection or even
sign a maintenance contract. Please take advice on this matter.
Before each use
⇒ Check connection cable for damages (risk of electrical shock); get the
damaged connection cable replaced immediately by an authorised customer
service person/electrician.
⇒ Check the high pressure hose for damages (risk of bursting).
Please arrange for the immediate ex- change of a damaged high-pressure hose.
⇒ Check appliance (pump) for leaks. 3 drops per minute are permitted and can
come out from the lower side of the appliance. Call Customer Service if there
is heavy leakage.
Weekly
⇒ Clean the sieve in the water connection.
Clean the sieve in the water connection
⇒ Take out sieve.
⇒ Clean the sieve from the outside and rinse it.
⇒ Insert sieve.
Every 500 operating hours, at least annually
⇒ Have the maintenance of the device performed by the customer service.
Troubleshooting
DANGER
Risk of injury by inadvertent startup of appliance and electrical shock.
– Prior to all work on the appliance, switch off the appliance and pull the
power plug.
– Get the electrical components checked and repaired only by authorised
customer service persons.
– Contact an authorised customer service person in case of problems not
mentioned in this chapter or if you are in doubt or when you have been
explicitly asked to do so.
Appliance is not running
⇒ Check connection cable for damages.
⇒ Check the supply voltage.
⇒ If the appliance is overheated:
Set the appliance switch to “0”.
Allow machine to cool down at least for 15 minutes.
Set the appliance switch to “1”.
⇒ Call Customer Service in case of electrical defects.
Pressure does not build up in the appliance
⇒ Check the nozzle size, install correct nozzle.
⇒ DE aerate the appliance (see “Start-up”)
⇒ Clean the sieve in the water connection.
⇒ Check water supply level (refer to technical data).
⇒ Clean the nozzle.
⇒ Replace the nozzle.
⇒ Contact Customer Service if needed.
Pump leaky
3 drops of water per minute are permitted and can leak from the bottom of the
appliance.
⇒ With stronger leak, have device checked by customer service.
Pump is vibrating
⇒ Check the water suction pipe for leaks.
⇒ DE aerate the appliance (see “Start-up”)
⇒ Contact Customer Service if needed.
Accessories and Spare Parts
Only use original accessories and spare parts, they ensure the safe and
trouble-free operation of the device.
For information about accessories and spare parts, please visit
www.kaercher.com.
Warranty
The warranty terms published by the relevant sales company are applicable in each country. We will repair potential failures of your appliance within the warranty period free of charge, provided that such failure is caused by faulty material or defects in manufacturing. In the event of a warranty claim please contact your dealer or the nearest authorized Customer Service centre. Please submit the proof of purchase.
EU Declaration of Conformity
We hereby declare that the machine described below complies with the relevant
basic safety and health requirements of the EU Directives, both in its basic
design and construction as well as in the version put into circulation by us.
This declaration shall cease to be valid if the machine is modified without
our prior approval.
Product: High pressure cleaner
Type: 1.520-xxx
Relevant EU Directives
2006/42/EC (+2009/127/EC)
2014/30/EU
2000/14/EC
2011/65/EU
Applied harmonized standards
EN 60335–1
EN 60335–2–79
EN 55014–1: 2006+A1: 2009+A2: 2011
EN 55014–2: 1997+A1: 2001+A2: 2008
EN 62233: 2008
EN 61000–3–2: 2006+A1: 2009+A2: 2009
EN 61000–3–3: 2013
EN 50581
Applied conformity evaluation method
2000/14/EC: Appendix V
Sound power level dB(A)
HD 4/9 P
Measured: 83
Guaranteed: 85
HD 5/11 P
Measured: 86
Guaranteed: 89
The undersigned act on behalf and under the power of attorney of the company
management.
Authorised Documentation Representative
S. Reiser
Technical specifications
Type | HD 4/9 P | HD 4/9 P | HD 5/11 P |
---|---|---|---|
GB | KAP | SA |
Main Supply
Voltage| V| 110| 120| 220
Current type| Hz| 50| 60
Connected load| kW| 1,4| 1,3| 2,0
Protection (slow, char. C)| A| 15| 13
Type of protection| —| IPX5
Extension cable, max. 30 m (Protection class 1)| mm²| 2,5
Water connection
Max. feed temperature| °C| 60
Min. feed volume| I/min| 9,5| 12
Suck height from open container (20 °C)| m| 0,5
Max. feed pressure| MPa| 1
Performance data
Operating pressure of water (using standard nozzle)| MPa| 9| 11
Size of standard nozzle| —| 030| 036
Max. operating over-pressure| MPa| 12| 13| 16,5
Water flow rate| I/min| 6,5| 6,2| 8,0
Max. recoil force of trigger gun| N| 14,76| 20,4
Values determined as per EN 60335-2-79
Hand-arm vibration value| m/s²| <2,5| 2,1| 3,2
Uncertainty K| m/s²| 0,6| 0,7| 0,8
Sound pressure level LpA| dB(A)| 70| 69| 73
Uncertainty KpA| dB(A)| 3
Sound power level LWA + Uncertainty KWA| dB(A)| 85| 85| 89
Dimensions and weights
Length| mm| 351
Width| mm| 312
Height| mm| 904
Typical operating weight| kg| 21,6| 20,5| 21,0
Type| HD 5/11 P| HD 5/11 P| HD 5/11 P
---|---|---|---
| EU CH| AR CN| GB AU
Main Supply
Voltage| V| 230| 220| 230…240
Current type| Hz| 50
Connected load| kW| 2,2
Protection (slow, char. C)| A| 10
Type of protection| —| IPX5
Extension cable, max. 30 m (Protection class 1)| mm²| 2,5
Water connection
Max. feed temperature| °C| 60
Min. feed volume| I/min| 12
Suck height from open container (20 °C)| m| 0,5
Max. feed pressure| MPa| 1
Performance data
Operating pressure of water (using standard nozzle)| MPa| 11
Size of standard nozzle| —| 036
Max. operating over-pressure| MPa| 16
Water flow rate| I/min| 8,1
Max. recoil force of trigger gun| N| 20,4
Values determined as per EN 60335-2-79
Hand-arm vibration value| m/s²| 2,7
Uncertainty K| m/s²| 0,8
Sound pressure level LpA| dB(A)| 73
Uncertainty KpA| dB(A)| 3
Sound power level LWA + Uncertainty KWA| dB(A)| 89
Dimensions and weights
Length| mm| 351
Width| mm| 312
Height| mm| 904
Typical operating weight| kg| 20,5
http://www.kaercher.com/dealersearch**59667830 Register and
win!
www.kaercher.com/register-and-win**
References
- agua.de - This website is for sale! - agua Resources and Information.
- Aparato
- Cleaning equipment and pressure washers | Kärcher International
- MASKINEN AB
- Cleaning equipment and pressure washers | Kärcher International
- Dealer Search | Kärcher International
- Reinigungsgeräte und Hochdruckreiniger | Kärcher