MWF MF-90 Locator and Multi-Coil Metal Detector User Manual
- June 9, 2024
- MWF
Table of Contents
- MWF MF-90 Locator and Multi-Coil Metal Detector
- WATERPROOF METAL DETECTOR
- Safety informations
- Product introduction
- Product features
- Product summary
- Change sensitivity
- Programming control
- **How to boot
- Warranty notice
- DO & DON’T
- Charging instructions
- CHARGING SUGGESTION
- Product maintenance
- Dive mode control
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
MWF MF-90 Locator and Multi-Coil Metal Detector
MULTI PINPOINTER
MF-90
WATERPROOF METAL DETECTOR
Safety informations
Warning:
- The user must practice before starting the detecting operations and discoveries
- Store in Cool and dry place 40-15 C %75-%5 humidity
Read & Understand The User’s manual before using this device
Product introduction
All waterproof metal detector – is an advanced handheld metal detector, using pulse induction (PI) technology, allowing you to hunt metal in water, land or any type of soil
Scope of application
A variety of applications – diving search, public safety inspection, police
detection, professional archaeology, positioning decoration line, etc.
Product features
- Sensitive and accurate
- Underwater waterproof depth up to 100 feet/ 30 meters
- Detection depth : 7 inches（8g pure gold ring and normal coin）
- Support type-C, micro USB interface
- Outdoor power bank charging
- Super endurance 10-7 days
Product summary
- Round detection disc
- Square detection disc
- Rod Detector
- Non-slip handle
- Packing box
Change sensitivity
Use of alarms
Programming control
While powered on, keep pressing on Mode button for 2.5 seconds to enter LED
light control programing, while indicator and flashlight both light up, quick
press on mode button to switch from four modes (indicator only, flash light
only, all off, all on)
Turn on/off tuning function. Under Expert Mode, quick press power button once
to activate/de-activate the retune function.
product mix
**How to boot
**
Warranty notice
Our company MWF provides a limited warranty to the original purchaser of its
products against all defects in original workmanship and material, under
normal use and service, for ONE year from the
date of purchase with the following exceptions:
- All warranties void if electronic part opened.
- Batteries are warranted for 90 days
- Cosmetic discoloration of surfaces
- Water flooding caused from battery cap seal.
Our company will not be liable for any further loss, damages, or expenses, including incidental or consequential damages directly or indirectly arising from the sale or use of this product.
DO & DON’T
- Always make sure battery cap is tightened before entering the water Only open battery cap with clean hand
- Always store your detector fully charged
- Always rinse equipment in fresh water after every dive
- Always apply silicone grease after cleaning O-ring
- Only open battery cap by clean hand
- Never leave your equipment in the rinse bucket. It may be damaged by other equipment.
RETRIEVE
- Swing the detector in overlap style.
- You can use side coil to pinpoint the target.
- Retune function. The retuning function is designed for ground balance to high mineralization condition or narrow down the target position. family is powered by Pulse Induction technology which will not produce any false to saltwater or black sand environment. You can use this function to help you get closer to the target. Just quick press the power button once to mute the alarm, and move again until you hear the target. You can also turn it off to make the operating simple.
Charging instructions
CHARGING SUGGESTION
- We strongly recommend you to use a quality wall charger when re-charge the probe. It will takes about 3~2 hours to fully charge.
- Laptop or desktop computer’s USB port produces lower power, which could make the recharging longer than wall charger.
- The probe will stop blinking when it is fully charged. You can leave the USB cable inside the recharge house after recharging.
Product maintenance
-
Use tap water or dampen a clean cloth with a mild detergent solution.
-
Wipe the device with the damp cloth.
-
Thoroughly dry the device. (Avoid chemical cleaners and solvents which can damage plastic components.)
-
Clean dust sand and fabric if spotted. Even a tiny grain of sand will cause water ingress.
-
Apply quality silicone O-ring grease thoroughly.
-
Change O-ring once a year at least. Use qualified original part only.
PRECAUTIONS
- The device is waterproof to 60M/200FT. It can withstand immersion in 60M/200FT of water for 30 minutes. After submersion, be certain to wipe dry and air dry the device before using or charging.
- Do not store the device where prolonged exposure to extreme temperatures can occur because it can cause permanent damage.
Dive mode control
Active alarm: tilt it upside down 3X to activate the detection mode
(DMA). The detector is ready to use. The red indication will blink twice every
3 sec. You are ready to search.
Mute alarming: Keep the coil up for 5 seconds to turn back to standby mode (DMS). It will come with 1sec alarm and the sensor is now stopping working. The red indication will blink every 3 sec. The unit is still powered on until power off at snorkeling mode.
www.mwf-metaldetectors.com info@mwf- metaldetectors.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>