mwf Wf-101-III Ground Water Detector User Guide
- June 6, 2024
- MWF
Table of Contents
Wf-101-III Ground Water Detector
Metal and Water Finder
USER MANUAL
User guide for WF 101 III, the latest device for detecting underground Water.
WWW.MWF-USA.COM
CONTENTS
Metal and Water Finder
Contents Safety Information Technical Specifications Device Parts Main Control
Unit Device Settings Get Started
Long Range Locating System (LRL)
Geophysical Searching System
Charging Setting Nots
Page 1 Page 2 Page 3 Page 5 Page 7 Page 9 Page 16 Page 16
Page 32
Page 40 Page 41
1 Page
SAFTY INFORMATION
The operating in high voltage areas would limit the results and performance
It’s better to turn off mobile while using the device.
Don’t operate two devices with same method of search at the same place
Don’t store in high temperature or high humidity
Disconnect the batteries before long time storage
The operator Must remove any metals that might affect the opreatin eg:Rings,watch, belt….
Any attempt to tamper the device or unapproved maintenance would void the warranty
For best power endurance and reliability. use heavy duty and high quality batteries thats for the devices which work on removable batteries
The user must practice before starting the detecting operations and
discoveries Store in Cool and dry place 15-40 C 5%-75% humidity
2 Page
Read & Understand The User’s manual before using this device
2
TECHNICAL SPECIFICATIONS
Search System :
Multisystem: 1.Long Range Locating System 2.Geophysical Search System
Search Principle:
1. Processing digital frequency signals to receive the energy of the targets’
electrostatic fields .
2. Sensing the energy of the magnetic and ionic fields of the targets.
3. Survey the earth’s layers and identify resistance electrical levels of the
earth, and processing the values and analyzing them to reveal the targets.
Operating Processor: Operating Frequency:
Power:
MICROCONTLLER PIC18 & ARM 7
1.From 1 KHz To 30 KHz 2.Special frequencies for measurement and verification
3.Measurement of electrical resistance Ohm
Two cells of Li-ion 3.7 volts ,2000 mA
Power Consumption: Battery Life:
Maximum of consumption 200 mA 6 work hours
Charger:
5,1 volt 2,1 Amp/2 hours charging
Display Type:
TFT Color Monitor 3.2 ” , 65.536 Color, 48Mhz , CDMA GPU
Specialized to detects: Natural water – Salty water – Mineral water All types of water .
Targets Discrimination:
Target Selection system:
Yes
Yes, can choose the target type before start search from the list of targets.
3 Page
TECHNICAL SPECIFICATIONS
DEPTH SEARCH::
800M, With the ability to control the level of search depth through the depth control interface.
DISTANCE SEARCH:
2500 M, With the ability to control the levels of the search distance through the distance control interface.
RESULTS FEEDBACK:
BLUETOOTH: WIRELESS: AUTOMATIC SMART GUIDANCE SYSTEM: VOICE ALERTS: VIBRATING
ALERT: OPERATING TEMPERATURE: STORAGE TEMPERATURE: HUMIDITY:
WEIGHT: DIMENSIONS: BAG DIMENSIONS:
Through orientation toward target location accompanied by sound + graphical
and vibration alerts..
Yes
Yes Yes, by graphical interface to locate the path and direction of the
target, and Acoustic commands
Yes
Yes From -15° C to 60° C
From -15° C to 40° C
It can be stored and work in the degree rate of air humidity at level 90%
Compound: 1 kg – disjointed in the bag: 3 kg
18.9×10.4×5.8 cm
18.9×10.4×5.8 cm
4 Page
DEVICE PARTS
The Main Control Unit The main control unit of the device, through which the
search criteria and settings for the device are determined, and it is
communicated with the attached search units via wireless connection.
USB Charger
An electric charger to recharge the device’s battery Values: Input: 100 – 240V
AC / 50 – 60Hz / 0.5A Output: 5V Continuous / 2A / 10W. Designed with a MICRO
USB charging port to match the universal charger system, making it easy to use
any charger available.
Geophysical Unit
This unit works to measure the intensity of the electrical resistance of the
soil and the underground materials and determine its identity, and its mission
is to detect and prospect for gold, minerals and underground voids with the
characteristic of accurate discrimination between targets.This unit works
through two scanning sensors only, which allows the system to work with ease
and comfort.
Probes and Wires
Made of the best types of stainless steel, a strong conductor of energy and
stainless, it is inserted into the soil and connected by power wires to
deliver the measurement waves sent from the device to the soil, to complete
the measurement process in the search area, between the two probes..
5 Page
DEVICE PARTS
Transceiver antennas
Two radio transmitting antennas. And two radio antennas to receive the waves
back from the target as a result of the transmitted waves.
Ground Reinforcement Unit
Equipped with a built-in transmitter that works on two systems, a signal
filtering system to confirm the location of the target, and a system equipped
with ground waves with a system for accurate transmission and enhancement of
the signal, this transmitter works with a bluetooth system to communicate with
the main unit through a special control interface to operate and close these
systems through the system interface
Sound Unit
This unit works to receive the sound alert system from the main unit
wirelessly and connects it to the headphone to enjoy the feature of the voice
alert through the headphone. So we can use it in both long range and hybrid
search systems. We can control the volume or even mute the volume through the
volume control switch located at the top of the unit.
Headphone
Connect via the headphone jack located on the top of the audio unit to hear
audio alerts wirelessly..
Grip
It is installed on the back of the main unit and is carried through it as it
allows a 360-degree circular movement, freely and smoothly
6 Page
THE MAIN UNIT
FRONT INTERFACE 1
10 2
9
3
4 8
5
7
6
1
Sockets for connecting the transmitter and receiver antennas
2 Display screen
3 Volume control key
4 Back key
5 Enter key
6 Power and lock switch 7 The key to tracking and focusing on goals 8 The keys move up, down, right, and left 9 Screen brightness control switch 10 Hybrid sensor connection socket
7 Page
THE MAIN UNIT
BACKGROUND 1
2
5 4
3
1 Laser indicator light 2 Installation of hand grip socket 3 The battery compartment
4 Charging socket 5 Audio output
8 Page
DEVICE SETTINGS
Turn on the device by pressing and holding ( ) on the front of the device for
three seconds.
The device will show the loading screen and then go to the main menu of search
systems.
Note : When the device is turned on for the first time, the device will
display a screen that enables you to choose the system language
9 Page
DEVICE SETTINGS
Explanation of the information bar at the top of the screen of the main unit
of the device The information bar facilitates and helps to quickly read the
device settings and know its status from the battery level and brightness of
the screen and know the time during the search process.
5
4
3
2
1
1 Battery charge level
2 Bluetooth system status icon
(activated / locked)
3 Volume level
4 Screen brightness level 5 Clock /Timing indicator
10 Page
DEVICE SETTINGS
Use the buttons ( then press the button ( press the button ( )
) to move between the menu options on the screen, ) to confirm the selection and to return to any position,
Settings menu
To enter the settings menu, press the button ( ) from the main menu to move
between the settings menu windows, and then press ( ) to enter the selected
settings window, and you will find there are several options for tuning. To
exit the selected settings window, press the button ( )to move again between
the configuration windows.
To control the brightness of the screen, go to the brightness adjustment
window, then press the ( ) button, then change the brightness level from 10%
to 100%.
11 Page
DEVICE SETTINGS Settings menu
To set the values of the sound alerts, scroll down and press the ( ) button,
then control the volume by going to the subwoofer icon, or you can hide the
sound completely You can activate or cancel the vibration option and play the
sound of clicking the keys of the main unit, in addition to activating and
deactivating the headphones option.
To change the system language, go to the language setting window, then press
the ( ) button, then select the desired language and confirm. WF 101 III is
multi-lingual, including Arabic.
To set the hour value, go to the clock setting window, then press the button
then set the time and confirm. The timekeeping watch facilitates clear viewing
and viewing of time.
12 Page
DEVICE SETTINGS
Settings menu
To set the bluetooth system, go to the bluetooth settings window, then
press the button ( ), then we turn on or off bluetooth through(
).
To set the password, go to the password setting window and then press the button ( ). You can activate or deactivate the password by going to the (disable / Enable) icons and pressing the ( ) button, and then enter the preset password. You can also change the password by choosing the (Change )Then enter the old password and then enter the new password, bearing in mind that the password must consist of four digits of numbers.
Note: In the absence of a preset password from the user, the default password
from the factory is four zeros (0000)
13 Page
DEVICE SETTINGS
To reset the factory, go to the factory reset window, then press the button( )
The confirmation window appears. Select to confirm.
Settings menu Verify device-product information (downloaded software version-
device model-manufacturer information-build number-serial number of device
-QRCODE image that enables you to go directly to the MWF website using the
camera of any mobile “smart phone” device).
Press the button ( ) to exit the settings menu and return to the main menu
14 Page
DEVICE SETTINGS Start Search
To start the search process, select the desired search system icon from the
main menu to enter the search systems. The available search systems will
appear on the screen, which are: the long-range detection system, the hybrid
search system, or the geophysical detection system. We will explain in detail
the entry of the section (Starting work) about the interfaces of each of the
systems attached to the device.
15 Page
START WORKING
Long Range Locator System
LONG RANGE LOCATOR (LRL)
System features
Many new technologies added to our long-range locator system, exclusive
technology is unprecedented, this system works to detects and locate targets
from far distance it directs the user and his leadership to the targets
location directly Embedded system for sensing and detection, where the device
can detect the targets through heading towards to target and is accompanied by
acoustic alarm indicator towards the target accurately Automatic smart
guidance system, to locate the path and direction of the target, through a
special graphics interface, where this system gives the user automatically
identify and vision about the direction and location of the target Smart
control interface to adjust the levels, search capabilities, and the type of
target you want to search for, too Targets List, composed of all kind of water
you can choose any target from this list to search for it separately, and
targets is: All types of water- Natural water-Mineral water – Salt water
Interface of accurate setting for search parameters, Multilevel to pre-control
levels of depth and distance of the search Depth up to 800 meters with a
control property in the signal level of the searching depths, through depths
options list, and starting from up to the selected depth: 50m 100m 200m
300m 400m 500m 600m 700m 800m Distance search up to 2500m, with a
control property in the level of front broadcast wave, through distance
options list and starting from 100m up to the selected distance: 100m 250m
500m 750m 1000m 1250m 1500m 2000m 2500m The guided laser function
is can be switched on or off from the system interface Equipped with built-
broadcast device works on two systems, signal filter system to confirm target
site, and ground transmitter system to strengthen of the signal
16 page
START WORKING
Long Range Locator System
The parts for Long Range System (LRL)
1 1 Main Unit 2 Transceiver Antennas 3 Carrying handle
17 page
2
3
START WORKING
Long Range Locator System
1
2
1 Connect the antennas to the designated place on the front of the unit 2
Place the handle at the bottom of the unit
Note: Do not forget to remove the batteries from the unit before storage to
ensure they are working properly
18 page
START WORKING
Long Range Locator System
Start Searching
Select Long Range Locator system by choosing LRL icon then press button
After entering the long-range Locator system, the options for determining
distance – target – and depth will appear on the screen We start by specifying
either by searching for all types of water or specifying the type of water to
be searched for: natural water – mineral water – salt water
19 page
START WORKING
Start Searching
Long Range Locator System
Long Range Locator interface To move between Target, Distance and Depth use these buttons To select the target and the search parameters use these buttons
After selecting the search options, go to the search option to start searching
then press the button Where we have an interface to choose between ground
transmitter and filter.
Note Make sure that the bluetooth system is activated from the bluetooth
configuration option or you can activate it directly when you enter the start
search window
20 page
START WORKING
Long Range Locator System
Start Searching
Before selecting the ground transmitter or filter Turn on the soil support
unit Initially we equip the ground support unit with the appropriate battery(1
- 9 V) Then we press the (ON / OFF) button to turn on the unit and then wait
for some time for the soil support unit to connect to the bluetooth system, as
we notice the disappearance of the blue light for the bluetooth symbol in the
soil support unit and its blinking slowly, and the two arrows surrounding the
bluetooth symbol in the main unit are also activated ( ) In both the working
system interface in the soil support unit and the status bar of the main unit,
the link between the unit is thus made
Then we screw the ground support unit well into the ground after making sure that it is turned on and connected to the main unit via bluetooth
Then we move to the main unit and choose the ground transmitter Note: We can
also select the TRANSMITTER option by pressing button from the soil support
unit
21 page
START WORKING
Long Range Locator System
Start Searching
The ground transmitter system offers a ground wave search system supported by
the fine-tuned transmission and enhancement system, and by the automatic
tuning system ATS
The automatic tuning system (ATS) is a special and new invention registered
for the MWF group, this system provides accurate and sure results in all types
of soils and terrain, as this system automatically identifies the soil and
gives the search automatic tuning commensurate with the type of soil and its
properties, while eliminating any radioactive interference Resulting from the
effects of rocky and mountainous lands, which may affect many devices, but
this system and its intelligence can sort, analyze and provide the necessary
levels of the frequency signal, the voltage and the wavelength of the signal,
which gives results free from any errors
22 page
START WORKING
Long Range Locator System
Start Searching
In the next step, the system search window appears, which shows the target
direction compass and the search criteria from a distance and depth, as well
as the laser light icon, which helps to easily identify the target point and
the drilling point accurately in various circumstances day and night
The user must carry the device through the carrying handle horizontal with the ground and slightly tilted towards the soil, as shown in the drawing
Soil
23 page
START WORKING
Long Range Locator System
Start Searching
First, we infuse the waves and fields coming out of the device, where we move
the device by hand to the right, then left slowly, and then the hand that
holds the device is steady
Right
Left
24 page
START WORKING
Long Range Locator System
Start Searching
If the target is found, the device will receive a read and signal by
automatically changing the device from the normal path to which the target was
located. This direction is the direction of the target’s location, and then
the device is installed in the same direction. Scan the target location and
install it by pressing again on the (Move) key to note that the device starts
to sound an alarm towards the target location, then we completely circumvent
the direction to which the device is directed to, to the opposite parking
point to notice the change of the device again and direction To the target
location and trigger the alarm Constantly, then we move away from the first
reading point to stand in another location away from the first point (10
meters) sideways, and we do the process of stimulation of the waves of the
device again and install the device and wait for reading, in case the target
is sure will go again to the same site and be We have confirmed the existence
of the target, and it is possible to do this method more than once in order to
make sure the direction of the target is correct, by taking more than one
reading from the device from different points, and if we notice theoretically
that all the readings that we made
third read User
second read User
first read User
Target
Intersection point
It is preferable to walk in a winding path while searching for the target and
changing direction of travel every five meters
25 page
START WORKING
Long Range Locator System
Start Searching
After confirming the target path, we press the button ( ) to ensure accurate
tracking of the target path and avoid the trouble of drilling at the wrong
point
Indication of left deviation in the direction of the specified target path
with the change of the alert
Indication of right deviation in the direction of the specified target path
with the change of the alert
Indication that you are on the right track for the specified target with an
alert
26 page
START WORKING
Start Searching
Long Range Locator System
How to locate the target
After confirming more than one reading of the direction of the presence of
target we press the move button to install the target path and we walk in the
same direction and normal to carry the device.Note during which the device
issued alerts to indicate that walking is in the right track towards the
indicator. It is an arrow indicating the direction of the convolution to
return to the right path, until we reach the point where we bypass the water
site and we will notice that the device has automatically changed direction
from its natural path to turn back to the location and the point of the
target, here we also rotate with the device to the location of the target. Hey
and we walk slowly and when we are directly above the target site we will
notice the device will start to turn left and right and this indicates that we
have identified the point of target
soil
27 page
The device turns off course after exceeding the target point
Target
START WORKING
Long Range Locator System
There is another way for us to more accurately determine where the target is located We are the process of squaring the target site by taking four readings of the target , point from four angles Square three meters from the target site, we will notice the intersection point of the four readings Theoretically it will be the midpoint of the target
User
device path
User
device path
Target
device path
User
device path
User
The user can know the approximate depth of the target by returning to the main
menu and setting the search settings again and change the depth level through
the depth list, ie for 5 meters we reduce the level of depth to 3 example if
the depth that was first selected meters and 20 meters and we enter the
information, and away About the target location hold the device and wait for
reading the target location, if there is a reading of the target meters, and
we do this process to reduce 3 site here know that the depth may be between
the level of depth until we know the approximate depth of the target
28 page
START WORKING
Long Range Locator System
How to detect the target depth
Reverse direction of the transmission unit Medium speed
The device turns off its path towards the target location
Soil This distance is equal to the depth of the target
Depth of target
Target
29page
START WORKING
Long Range Locator System
Start Searching
Now to make sure Whether the water source is abundant by using the Filter
system we have to repeat the searching process by choosing the Filter
Ground transmitter
Filter
Then we implant the soil support unit in the ground well, about 10 meters from
the target and stand in the middle between the soil support unit and the
target holding the device, we stimulate the device and install the device with
the fist, waiting for the reading If the device is directed towards the
target, this indicates that the target is abundant , but if the device is
directed towards the soil support unit , this means that is the target density
is Low
The device is directed towards the soil support unit
the target density is Low
The device is directed towards the target the target is abundant
soil
target
10 M
5 M
5 M
30 page
START WORKING
Long Range Locator System
Signal filtering system to confirm target location and abundance of water, and
the system equipped with ground waves with the system for accurate
transmission and enhancement of the signal, this transmitter works with a
bluetooth system to communicate with the main unit through a special control
interface to operate and close these systems through the system interface
It provides a signal filtering system, to avoid any interference caused by any
radio or frequency waves present in the air
31 page
START WORKING
Geophysical Search System
Geophysical Search System
System advantages
This system works on measuring the intensity of the soil electrical resistance
and to identify substances found underground and identification, and its
mission to detect and exploration for underground water with a property of
accurate discrimination between all types of water. Special display interface
of this system gives the user an integrated information about the search
process and search steps are automatically. This system scans and detect the
soil automatically and shows complete results about the discovered targets
directly on the screen Feature of automatic help messages, which appear on the
screen for the user to alerting on a particular command or guidance to execute
a specific command. The system works by two electro-rod scanning only,
allowing to work in this system with ease and comfortable. Property of
determine the target depth and accurately, through a special system to
identify and measure the depth of discovered target. Advanced Search and
identification techniques, working on functions smart detection, which works
on the smart systems of detection and analysis for the target location.
Multiplier check scanning system and at the immediate time for the location,
which gives the user, gives credible and proven results Accurate
discrimination between the target’s types, and to clarify the target, type,
size and name in the screen directly. Smart verification system of connecting
the electrodes in the soil and by wire or non-connected and clarified it on
the screen through the alerts messages.
32 Page
START WORKING
Geophysical Search System
Components of a geophysical search system
1
1 The Main Unit 2 Geophysical Unit
3 Ground Probes 4 Connection Wires
33 Page
START WORKING
Geophysical Search System
Installation of the geophysical search system
1 3
2
4
1 Connect the geophysical unit
with the main unit
2 Connect the wires to the probes
3 Connect the wires to
the geophysical unit
4 Dip the probes well into
the soil
34 Page
START WORKING
Geophysical Search System
One of the great advantages of the geophysical system in the WF 101 III is
that it works with only two scanning sensors, which allows for easy,
comfortable and fast work.
Note: Make sure that the wires are connected well, noting that when it is not
connected
well and the probes are connected to the geophysical unit when starting the
search, the developed geophysical system provides you with a smart system for
verifying the conductivity of the electrodes in the soil and the wires or not
connecting them and explaining this on the screen through warning messages.
We provide a quick set of tips to ensure the best results and avoid mistakes.
Quik Tips 1- Place the electrodes on the largest possible area:
This means that if the site to be searched is an area of 5 m², the poles must
be placed on an area exceeding 5 square meters as shown in the drawing
the soil
2 M
1
2.5 M 5 M
Search site m² 5 2
35 Page
START WORKING
Geophysical Search System
2- Ensure that the distance between the electrodes is equal: This means that if the distance is, for example, 6 meters, the distance between the first pole and the second pole must be equal to 3 m / 3 m
3 M the soil
6 M
3 M
1
2
Important note: If the error signal persists for the non-wiring mode, this
means that
there is something wrong with the wires and it must be checked and the
connections between the connecting tweezers, the wires and the probe are well
also and if verified and this note continues, This means that the conductivity
of the soil is very weak and the sensor site needs to be moistened with water
more, and sometimes you may have to drill 10 to 15 cm at the site of the
sensor site to obtain conductivity with the soil.
36 Page
START WORKING
Geophysical Search System
Start Search
After completing the instructions and connecting the electrodes, we choose the
geophysical search system from the main interface of the search systems
Then the main search interface of the system appears, which contains the option to start searching and the search progress indicator. And a graphic showing the status of the probes connection, where an error signal appears in the event that the correct connection is not attached to the sound alert. Or a correct signal indicates that the connection condition is sound and we can start searching
37 Page
START WORKING
Geophysical Search System
Start Search
To start the search, the user must press the ( ) key to run the scanning
process.
The color of the indicator for starting the search will change from blue to
gray when turned on and when scanning is finished it will return to blue.
We wait for the search indicator to progress until the end of the reading of
the area of the site confined between the probes embedded in the ground.
Upon completion of the reading, the target type and depth will be shown on the
screen automatically.
The device scans between the two probes according to their distance from each
other, the device measures the electrical energy levels of the soil to
determine whether there are those targets that this system is looking for or
not, and the measurement process depends on the sensing process and vertical
induction to measure the levels of electrical resistance of the ground the
device can distinguish Between the identity and the electrical value of each
target.
38 Page
START WORKING
Geophysical Search System
Start Search The WF101III’s geophysical search system features a precise
distinction between target types, with the target’s name and type indicated on
the system’s search interface. It is also characterized by the feature of
accurately determining the depth of the target through a special system for
determining and measuring the depth of the detected target. The value for
measuring the depth is an approximate value and may vary according to the
position of the target and the type of soil as well, but this feature enables
you to know the approximate depth on which the target is located.
Determine and locate the target:
The user must move the location of the sensors while maintaining a distance
between them of at least 2.5 meters, and when leaving the target site and
placing it outside the target area, you will notice that the device gives you
a result (there is no target), this means that the target site has been
skipped and the sensors have been placed outside the target site Here, the
sensors must be gradually returned to the first target area in order to
determine the target location accurately, and when the first result is
obtained, this means the beginning of the target site’s existence. The user
has to perform this operation from two different sides in order to be able to
determine the location of the target more accurately.
39 Page
BATTERY CHARGING
Charging Information
You can continue charging the battery when the device is closed or switched
on, knowing the added charge level All in real time with smart charging
systems. When the device is connected to the charger in the off state, the
battery charge progress indicator will appear on the screen in percentage As
shown:
The device also offers the battery and smart charging feature, which gives the
user an accurate tracking of the energy level, Accurate visual and audible
notifications of battery level and alerts before the power runs out.
During work and when the battery level reaches 15% We notice a change in the
shape of the battery indicator to this state
While charging the device, we notice the change of the battery level indicator
To this shape when the battery is 100% full
40 Page
NOTES
41 Page
Metal and Water Finder
United States of America – illinois www.mwf-usa.com info@mwf-usa.com +1 ( 708
) 364 9602
Turkey – istanbul
www.mwf-metaldetectors.com info@mwf-metaldetectors.com +90 ( 212 ) 222 0946
+90 ( 212 ) 222 0947
References
- metaldetectors.com
- USA Location information - USA.com
- HOME - MWF METAL WATER GOLD DETECTORS
- Home - MWF Group USA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>