IOTA IIS3P Series Three Phase Inverter User Guide
- June 9, 2024
- IOTA
Table of Contents
- IIS3P Series Three Phase Inverter
- IMPORTANT SAFEGUARDS
- CHAPTER 1 INTRODUCTION
- HOW TO USE THIS MANUAL
- CHAPTER 2 ENVIRONMENT
- CHAPTER 3 STARTUP AND SHUTDOWN PROCEDURE
- SHUTDOWN PROCEDURE
- MAINTENANCE BYPASS PROCEDURE
- CHAPTER 4 OPERATION
- CHAPTER 5 FRONT PANEL DISPLAY
- Control Functions
- Program Functions
- CHAPTER 6 SPECIFICATIONS
- CHAPTER 7 MAINTENANCE AND SERVICE
- TROUBLE SHOOTING CHART
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
IIS3P SERIES
THREE PHASE
4.8 kW – 16.7 kW
User’s Guide
113782C – System
Users Manual
IIS3P Series Three Phase Inverter
CAUTION
READ ENTIRE MANUAL AND REVIEW ALL DOCUMENTATION BEFORE ATTEMPTING SYSTEM
INSTALLATION
FOR SERVICE OR INSTALLATION INFORMATION:
TELEPHONE: 610-868-5400 (24 HR.
HOTLINE)
FAX: 610-954-8227
FOR YOUR PROTECTION
PLEASE COMPLETE AND RETURN WARRANTY REGISTRATION CARD IMMEDIATELY.
This unit contains LETHAL VOLTAGES. All repairs and service should be performed by AUTHORIZED SERVICE PERSONNEL ONLY! There are NO USER SERVICEABLE PARTS inside this unit.
IMPORTANT SAFEGUARDS
When using electrical equipment, you should always follow basic safety precautions, including the following:
- READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
- Do not install the system outdoors.
- Do not install near gas or electric heaters or in other high-temperature locations.
- Use caution when servicing batteries. Depending on battery type, batteries contain either acid or alkali and can cause burns to skin and eyes. If battery fluid is spilled on skin or in the eyes, flush with fresh water and contact a physician immediately.
- Equipment should be mounted in locations where unauthorized personnel will not readily subject it to tampering.
- The use of accessory equipment not recommended by Manufacturer may cause an unsafe condition and void the warranty.
- Do not use this equipment for other than its intended use.
- Qualified service personnel must perform all servicing of this equipment.
SAVE THESE INSTRUCTIONS
The installation and use of this product must comply with all national, federal, state, municipal, or local codes that apply. If you need help, please call Service.
User’s Guide
An on-site permanent log of the inspection, testing, and maintenance of the
emergency electrical power supply system shall be maintained in accordance
with the Manufacturer’s operating manual. The log shall include: The date on
which the inspection, testing, and maintenance exercise was carried out The
name of the person(s) who performed the inspection, testing, and maintenance.
A note of any unsatisfactory condition observed or discovered, and the steps
taken to correct the condition
CHAPTER 1 INTRODUCTION
Keep this manual and the System Installation Guide in the folder mounted
inside the unit.
This unit is a microprocessor controlled PWM (Pulse Width Modulated) pure sine
wave based DC to AC power inverter utilizing IGBT technology. It integrates a
fully automatic 3rate battery charger, a solid-state transfer system, control
circuitry, self testing and recording digital meter display, and maintenance
free sealed lead calcium type
batteries. The system components are carefully matched to make the unit a
completely self-contained, fully automatic standby power source for operation
on all types of lighting loads. The batteries are sized and tested per UL-924
and Life Safety Code ANSI / NFPA 101, providing emergency power for a minimum
of 90 minutes.
If the duration of a power failure is greater than the batteries storage
capability, the inverter will automatically shut down when the battery voltage
reaches 85% of the nominal DC voltage. This feature protects the battery from
being permanently damaged from a deep discharge that could cause cell
reversal. This battery protection feature is called “Low Voltage Disconnect”
or L.V.D.
When the AC power is restored after a full discharge, the system will be ready
for another power failure within 24hrs. If another power failure occurs before
the 24-hour recharge time, the run time will be decreased.
The front panel display incorporates an alphanumeric 2×20 LCD character
display, LED status indicators and a 4 x 4 keypad. All user interface
functions are available from the front panel assembly.
Utilizing a small footprint, this unit is for use with any lighting load
including quartz, HID, incandescent, fluorescent and halogen.
HOW TO USE THIS MANUAL
This manual tells you how to start, operate, and communicate with your unit
and lets you know how to get more information for special situations.
Please record your unit’s model number, serial number, and part number below.
You can find these numbers on the labels on the inside panel.
Model Number __
Serial Number __
Part Number ___
Service and Support
We are committed to outstanding customer service. A service technician is available 24 hours a day, 365 days a year. Service is also available 24 hours a day to give you access to technical notes and product information. You can also visit our web site.
NOTE: Please have your unit’s Serial and Model numbers available when you call; this number is located behind the right door. Contact SERVICE one of the following ways: Service Number: 610-868-5400 Service Fax: 610-954-8227
CHAPTER 2 ENVIRONMENT
Make sure the environment is a clean, cool, dry place with normal ventilation.
Storage Temperature
Store the batteries (in the system or battery cabinet) at -18 to 40°C (0 to
104°F). Batteries have a longer shelf life if they are stored below 25°C
(77°F). Keep stored batteries fully charged. Recharge the batteries every
90–120 days. The system or battery cabinet without batteries may be stored at
-20 to 70°C (-4 to 158°F).
Ventilation
The air around the unit must be clean, dust-free, and free of corrosive
chemicals or other contaminants. Do not place the system or batteries in a
sealed room or container.
Operating Temperature
System can operate from 20° to 30°C (68° to 86°F) and up to 95% relative
humidity. The batteries’ service life is longer if the operating temperature
stays below 25°C (77°F).
Batteries
The temperature should be near 25°C (77°F) for optimum battery performance.
Batteries are less efficient at temperatures below 18°C (65°F), and high
temperatures reduce battery life. Typically, at about 35°C (95°F), battery
life is half of what it would be at a normal temperature of 25°C (77°F). At
about 45°C (113°F), battery life is one-fourth of normal.
Make sure that heaters, sunlight, air conditioners, or outside air vents are
not directed toward the batteries. These conditions can make the temperature
within battery strings vary, which can cause differences in the batteries’
voltages. Eventually, these conditions affect battery performance.
If the batteries are not in the system, remember that the batteries should be
installed as close as possible to the unit to reduce DC wiring costs and
improve battery performance.
Do not allow tobacco smoking, sparks, or flames in the system location because
hydrogen is concentrated under the vent cap of each cell of the battery.
Hydrogen is highly explosive, and it is hard to detect because it is
colorless, odorless, and lighter than air.
Every type of battery can produce hydrogen gas, even sealed maintenance-free
batteries. The gas is vented through the vent caps and into the air, mainly
when the unit is charging the batteries. The batteries produce the most
hydrogen when maximum voltage is present in fully charged batteries; the
batteries do not produce hydrogen during float charging. The amount of current
that the charger supplies to the batteries (not the battery ampere-hour)
determines how much hydrogen is produced.
High Altitude Operation
The maximum operating ambient temperature drops 1°C per 300m (2°F per 1000 ft)
above sea level. Maximum elevation is 3000m (10,000 ft).
CHAPTER 3 STARTUP AND SHUTDOWN PROCEDURE
Refer to the Installation Manual to secure the unit and install AC and DC
wiring.
STARTUP PROCEDURE
For the initial startup of the system, follow the instructions in the Startup and Warranty Validation Form. Failure to do so will void warranty.
CAUTION: HAZARDOUS VOLTAGES – ONLY QUALFIED SERVICE PERSONNEL SHOULD PERFORM PROCEDURE.
- Verify that the installation switch located on the inverter chassis is in the OFF position. Verify that AC input is disconnected.
- Press and hold the DC Pre-charge switch located on the inverter chassis for approximately five seconds and then install the battery fuse. If a large flash occurs, the batteries are not connected properly. Call service immediately.
- Energize the Mains AC input by turning on the units input circuit breaker and/or the Distribution Panel breaker located upstream from the inverter.
- Turn the installation switch to the On position. The Front Panel display should now be illuminated and a slight hum should be heard from the inverter transformer. The
unit is now charging and the output should be energized.
SHUTDOWN PROCEDURE
- Interrupt the AC Mains to the machine by the Distribution Panel Breaker or the machines input circuit breaker. The Inverter should then start.
- Turn the installation switch located on the inverter chassis to the off position. The inverter should stop.
- Disconnect the main battery fuse located on the inverter chassis.
CAUTION: HAZARDOUS VOLTAGES STILL EXIST AT THE BATTERY TERMINAL BLOCK AND
WITHIN THE SYSTEM. AUTHORIZED SERVICE TECHNICIANS MUST DISCHARGE DC CAPACITORS
AND TURN OFF UTILITY POWER BEFORE SERVICING EQUIPMENT.
CAUTION: DO NOT LEAVE THE SYSTEM SHUTDOWN FOR A PROLONGED LENGTH OF TIME.
LEAD BASED BATTERIES WILL EXPERIENCE PERMANENT DAMAGE FROM LACK OF CHARGING
AFTER A FEW MONTHS.
MAINTENANCE BYPASS PROCEDURE
CAUTION:
HAZARDOUS VOLTAGES – ONLY QUALFIED SERVICE PERSONNEL SHOULD PERFORM PROCEDURE.
MAINTENANCE BYPASS SHOULD NOT BE PERFORMED WHEN SYSTEM IS IN BATTERY EMERGENCY
MODE.
System Into Bypass Mode
- Open System doors. Locate Maintenance Bypass Switch behind left-hand door on chassis.
- Turn Maintenance Bypass Switch from normal mode (UPS) to bypass mode (BYPASS).
- Locate Installation Switch behind right-hand door on chassis. Turn the Installation Switch to the (OFF) position.
- Locate Input Circuit Breaker (CB1) behind left-hand door on chassis. Turn the Input circuit Breaker to the (OFF) position.
- Locate Main Battery Fuse behind right-hand door on chassis. Remove Main Battery fuse.
CAUTION:
HAZARDOUS VOLTAGES STILL EXIST AT THE BATTERY TERMINAL BLOCK AND WITHIN THE
SYSTEM. AUTHORIZED SERVICE TECHNICIANS MUST DISCHARGE DC CAPACITORS BEFORE
SERVICING EQUIPMENT.
WARNING:
DO NOT LEAVE THE SYSTEM SHUTDOWN FOR A PROLONGED LENGTH OF TIME. LEAD BASED
BATTERIES WILL EXPERIENCE PERMANENT DAMAGE FROM LACK OF CHARGING.
Remove all Battery Fuses from all Battery Cabinets.
System On Line From Bypass Mode
- Verify that the Installation Switch located on inverter chassis is in the (OFF) position.
- Install all Battery Fuses in all Battery Cabinets.
- Press and hold DC Pre-charge switch located on the inverter chassis for approximately five seconds and then install the Main Battery Fuse on the inverter chassis. If a large flash occurs, the batteries are not connected properly. Call service immediately.
- Turn the Input Circuit Breaker (CB1) to the (ON) position.
- Turn the Installation Switch on the inverter chassis to the (ON) position. The Front Panel Display will now be illuminated and a slight hum should be heard from the inverter transformer. The unit is now charging the batteries.
- Turn the Maintenance Bypass Switch from bypass mode (BYPASS) to normal mode (UPS).
The emergency equipment is now protected by the inverter system.
CHAPTER 4 OPERATION
The following is a description of the status LED’s located on the front panel.
AC Present
When the AC Mains is present, the LED will illuminate. If a power failure
was long in duration, or the AC mains was disconnected by some other means
(Circuit breaker open) the AC Present LED would not be illuminated. When the
control circuit senses that the line has dropped below an acceptable level
(Black Out, Brown Out, or Transient), the inverter will energize for at least
one minute. So, if the power failure was a momentary glitch, the AC present
LED would be illuminated but the inverter would be running.
System Ready
When the system has adequate battery voltage to transfer, the System Ready
LED will illuminate.
This feature prevents damage from multiple deep discharges of the battery.
Battery Charging
When the AC Mains is connected to the line and the battery is charging
under normal conditions, the Battery Charging LED will illuminate.
Battery Power
When the inverter is producing output power (battery is being discharged), the
Battery Power LED will be illuminated.
Fault
This is a summary Fault indication. When there is a fault condition
present, the Fault LED will illuminate. To view which fault is present, use
the keypad and LCD display feature.
The front panel display will provide the user with a variety of information.
It has a full compliment of Meter functions, Control functions and Program
functions.
CHAPTER 5 FRONT PANEL DISPLAY
The Front panel consists of a 2 x 20 alpha numeric LCD display with LED Back lighting, 5 Status LED indicators and a 4 x 4 keypad for user interface.
Control Panel Keypads
Table 5.1 Keypad Functions
Key Name | Description |
---|---|
Meter (Blue) | Pressing this key will activate Meter Functions |
Control (Red) | Pressing this key will activate Control Functions |
Program (Black) | Using this key, you can enter passwords or change parameter |
values. To enter passwords, press [PROGRAM], enter the password, and press
[ENTER]. NOTE: A password must be entered to change parameters.
Enter (Grey)| This key records or enters a task you perform using the control
panel keys.
[ ]| This key functions as Left scroll key
[ ]| This key functions as Right scroll key
[0]| This key works as a number key; it is also used to display active
alarms when in CONTROL Mode.
[ 1 ] through [ 9 ]| These keys work as number keys.
Meter Functions
Meter functions are available by pressing the METER keypad to get to the Meter
Menu and then pressing the desired function keypad. (See figure 5.1)
Table 5.2 Meter Functions
Function | Description | Keypad Text |
---|---|---|
Voltage Input | Measures the AC Input Voltage to the Inverter | V IN |
Voltage Output | Measures the AC Output Voltage from the Inverter | V OUT |
Current Output | Measures the AC Output Current from the Inverter. If optional |
Normally Off loads is connected, it will read the sum of Normally On and
Normally Off outputs.| I OUT
Battery Voltage| Measures Battery Voltage| V BATT
Battery Current| Measures the Battery Current. When in charge mode, the
current will be positive. When in Inverter mode, the current will be
negative.| I BATT
VA Output| Multiplication of the output voltage and output current| VA OUT
Inverter Watts| Multiplication of the battery voltage and the battery current|
INV. WATTS
Inverter Minutes| Total minutes the system has run on inverter| INV. MIN
Temperature| Measures the ambient temperature of the electronics enclosure.|
TEMP
System Days| Total days the system has been in service.| SYS. DAYS
Control Functions
Control functions are available by pressing “CONTROL” to get to the Control Menu and then pressing the desired function.
Table 5.3 Control Functions
Function | Keypad Text |
---|---|
Test Log | TEST LOG |
Event Log | EVENT LOG |
Initiate Test | TEST |
Alarm Log | ALARM |
Buzzer Silence | BUZZER |
-
TEST LOG – View the Test Log of the last 75 monthly or Yearly Tests. View the Date, Time, Duration, Output Voltage, Output Current, Temperature and Fault Status.
Use the left and right scroll key to change event number. Use the ENTER key to select desired event number. Use the left and right scroll key to view event information about the event. Use the TEST LOG key to return to the event number. -
EVENT LOG – Identical to the TEST LOG except this log records the past 75 events.
-
TEST – Pressing the TEST key will initiate a 1-minute test. This test will be recorded in the Event log since it is not part of the scheduled monthly or yearly test.
-
ALARM – View the Alarm log of the last 50 alarms. View the Date, Time and Alarm.
Use the left and right scroll key to change alarm number.
Use the enter key to select alarm number.
Use the left and right scroll key to view information about the alarm.
Use the ALARM key to return to event number. -
BUZZER – Pressing this key silences the audible buzzer from a fault condition or an intermittent beep when the inverter is under battery power. If a fault caused the buzzer to alarm and the alarm is silenced, the buzzer will return after 24 hours or after the fault is cleared.
Program Functions
User Program Functions
All program functions are password protected. The password for user level is
1234. When the PROGRAM keypad is pressed, the display will prompt the user for
the password. After the password is entered (1234 + ENTER key), the user can
change the Date, Time, Month Test Date, Month Test Time, Yearly Test Date and
Yearly Test Time, Load Reduction Fault, Low VAC Alarm, High VAC Alarm, Ambient
Temp Alarm and Near Low Battery settings. Time is always in the 24 hour
standard. Example 4:00 PM is 16:00.
Table 5.4 Program Functions
Parameter | Format | Factory Default |
---|---|---|
Date | MM/DD/YY (Month, Date, Year) | Current Date |
Time | HH/MM (Hours, Minutes) | Eastern Stand Time |
Monthly Test Date | DD (Date) | 15t” of the Month |
Monthl Test Time | HH/MM (Hours, Minutes) | 5:00 |
Yearly Test Date | MM (Month) | 1 |
Yearly Test Time | HH/MM (Hours, Minutes) | 8:00 |
Load Reduction | AAAA(Amps) | 0.0A |
Low VAC Alarm | VVVV(Volts) | 1.0V |
Hie h VAC Alarm | VVVV(Volts) | 999.9V |
Ambient Temp Alarm | DDD(Degrees Centigrade) | 70°C |
Near Low Battery | VVVV(Volts) | See Table 5.5 |
-
Near Low Battery Voltage is in VVVV (Volts). The last digit entered is after the decimal place.
I.E. (430 + ENTER) will register 43.0VDC. Please refer to table 5.5. -
Load Reduction Fault is in AAAA (Amps). The last digit entered is after the decimal place.
I.E. (480 + ENTER) will register 48.0 Amps. If the output current under battery power is 10 percent below this number, the alarm will be set. -
Low AC Voltage Alarm is in VVVV (Volts). The last digit entered is after the decimal place.
I.E. (1200 + ENTER) will register 120.0 Volts. If the Input AC Voltage goes below this number the alarm will be set. -
High AC Voltage Alarm is similar to Low AC Voltage Alarm.
-
Ambient Temperature Alarm is in DDD (Degrees Centigrade). I.E. (75 + ENTER) will register 75 deg. C. When the ambient temperature internal to the inverter enclosure goes above the set point the alarm will be set.
Table 5.5 Near Low Battery Voltage
DC Voltage | Near Low Battery |
---|---|
144VDC | 130VDC |
180VDC | 162VDC |
240VDC | 216VDC |
CHAPTER 6 SPECIFICATIONS
‘Input| Voltage
Input Power Walk-n
Input Frequency
Synchronezng Slow Rate
Protection
Harmonic Distortion
Power Factor| 120/208 or 2/ 7/480Vac 3-phaeo 4-wie .10% -15%
Limiting inrush cunent to less than 125%, 10 tines for 1 the cycle 60Hz, 41-
3%, 5011z Avatable upon request
1Hz por second nomnal
Input Clog Breaker
< 10%
.5 lagilead
---|---|---
Output| Voltage
Stair Voltage
Dynamc Voltage
Harmonic Distortion
Output Fiequency
I oad Power Factor
Invetter Overload
Protection| 120/208 or 277/480Vac 3-phase 4-wire.
I oad curtail change +14%, battery descharce .14%
+/- 3% tor -q -25% load stop change, -il 6% for a 50% load stop change, memory
wain 3 cycles < 396 TIID for /near load
60Hz +I .0511z ding emergency mode
5 lag to 5 lead
115% for 5 mbutes
Output Clout Breaker
Battery| Type
Charger
Protection
Diconnect
Options Ftaiines| Vatve-regulafed sealed lead-calcin. Contact factory for
additional battery types.
Microprocessor axittallai for various battery types and temperature
compaisatsi (recharge pet I1L924 spec) Automatic low hallow ckscannect,
autanalc restart upon Silty return.
Fuse- and-Fuse/ Circuit [Maker above 24KVA
Extended runtimes amiable. Consult factory for additional Somalian.
Environmental| Altitude Operating Temperature
Storage I emperatu in
Relative Hurnidty| < 10,000 bet (above sea level) without donating 20 to 30
degree Ceisks
-20 to 70 degrees Celsius (electronics only) < 95% (non-condensing)
!General| Design Generator Input Untie Pant Mete Sig Alarms Commts•atiormS
Manual maintenance ttenance Bypass
Alarm Contacts Warranty
factory Stad-up 5 Year Service Plan| Stand-By UPS. MUM twodertypo utiliztig
1GDY technology with 2mS transfer tine
Compatble with generators.
Microprocessor extolled 2 x 20-dialactor Display with touch pad controls &
functions
5 I FI) skaters & alarm with Sighadc feature
Input & output Vatic°, Flattery Voltage, flattery & Output Current, Output VA,
Temperature, Inverter Wattage Nigh/Low Battery Charger FauK, Near Low Gately,
Low Daum, Load Reduction Fault, Output Overload, Hightl ow AC Input Volts itch
Ambient I emperature, Inverter Fault, Output F auN, Optional Grant lircicer I
rp
RS232 port 0)139) Standard
Optional &maw Fenn “C Contacts
1 year standard warranty ndudes all parts, labor, & travel expenses within 48
contiguous states. Up to 10 years prorated warranty on batteries. Extended
warranties, prove rtat ir e maitenance and customized service plan are
available.
Purchase factory sta it-up & receive 1 additional year of warranty.
Purchase 5 year service plan & receive tree baby slat-up.
Physical| Calinot Coolhg Cable Entry Access| Feeeslandirg MENA Type 1
Forced Ai, durtg emergency mode. Top orSide Front
CHAPTER 7 MAINTENANCE AND SERVICE
The Self-testing feature of the inverter ensures that the system is tested at
least once per month for 5 minutes and once per year for 90 minutes. If there
are any problems with the self-tests, the fault log shall indicate which
faults occurred. Please see the fault descriptions and troubleshooting guide.
A few simple maintenance operations performed periodically will help ensure
many years of trouble free operation. Battery terminals should be checked for
tightness and corrosion. If severe corrosion is evident, maintenance is
required to correct this situation. Since the unit depends on unrestricted
airflow for cooling of power handling components, it is important to keep the
air vents free of any obstruction. If the environment tends to be extremely
dusty, occasionally blow away any accumulation of dust on components. Please
follow the shutdown procedure before cleaning.
CAUTION: Follow the shutdown procedure (See Chapter 3) before cleaning.
An authorized technician only should perform Service!
Table 7.1 Preventive Maintenance Schedule
SERVICE TO PERFORM: | PERFORM SERVICE EVERY: |
---|---|
3 MONTHS | 6 MONTHS |
1.TEST UNIT:
NOTE: Perform manual test only when critical load is connected but not
required.
Output voltage should be present.
Confirm operations of front panel indicators.| X| |
| |
| |
| |
| |
| |
| |
| |
2.INSPECT BATTERIES:
All connections are tight.
Connections have no corrosion. (Clean if
necessary).| | X|
| |
| |
| |
| |
| |
| |
| |
CLEAN UNIT: NOTE: Unit must be shut down during this service.
Inspect air vents and clean if necessary.
Clean excessive dust from inside cabinet(s).
Clean excessive dust from fan(s).| | | X
| |
| |
| |
| |
| |
| |
| |
“X” Indicates when to perform service. Lines below the “X” are for the date of service.
TROUBLE SHOOTING CHART
WARRANTY
For warranty information on IOTA IIS Central Inverters and battery components,
visit www.iotaengineering.com or call IOTA
Customer Service.
OUT OF WARRANTY REPAIR CHARGES AND LABOR
Contact Field service for current parts and labor rates. A minimum rate will
be assessed.
The manufacturer will not proceed with repairs of an out of warranty unit
until authorization in the form of a purchase order is received from the
customer. The unit for repair must be returned prepaid with an RMA number on
the carton. For travel to the job site, a quote “Not to Exceed” estimate will
be given. A purchase order to cover that amount is required before a trip to
the job site is made.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>