Russell Hobbs 26340-56 Ultra Coconut Smooth Stream Iron User Manual

June 9, 2024
Russell Hobbs

Russell Hobbs logo 26340-56 Ultra Coconut Smooth Stream Iron
User ManualRussell Hobbs 26340 56 Ultra Coconut Smooth Stream
Iron

26340-56 Ultra Coconut Smooth Stream Iron

Russell Hobbs 26340 56 Ultra Coconut Smooth Stream Iron - icon
11 www.russellhobbs.comRussell Hobbs 26340 56
Ultra Coconut Smooth Stream Iron - Figure 1

IMPORTANT SAFEGUARDS

Follow basic safety precautions, including:
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been supervised/instructed and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be done by children unless they are older than 8 and supervised. Use and store the appliance out of reach of children under 8 years.
Keep the iron and its cord out of reach of children less than 8 years of age when it is plugged in or cooling down.
Use the iron, or set it on its heel, on a stable, level, heat-resistant surface, preferably an ironing board.
Don’t leave the iron unattended while plugged in, or while it’s standing on the ironing board.
Unplug the iron before filling, before cleaning, and after use.
Do not immerse in any liquid.
Don’t operate the appliance if it’s dropped or damaged, or if it malfunctions or leaks.
If the cable is damaged, return the iron, to avoid hazard.
**** The surfaces of the appliance will get hot during use.

  • Don’t iron clothing while it’s being worn – you’ll injure the wearer.
  • Don’t use the appliance for any purpose other than those described in these instructions.
  • Don’t scratch the soleplate – avoid buttons, zips, etc.
  • The appliance has a protective thermal fuse, which will blow if it overheats. If this happens, the appliance will stop working, and must be returned for repair.

HOUSEHOLD USE ONLY

PARTS

1. Light
2. Temperature control
3. Water inlet
4. Cover
5. Spray nozzle| 6. Soleplate
7. Steam control
8. Heel
9. Mark
---|---

BEFORE USING FOR THE FIRST TIME

  • Remove labels, stickers and packaging from the iron and soleplate.
  • Don’t worry if the iron smokes a bit at first, it’ll stop as the element cures.
  • Iron an old piece of cotton fabric, to clean the soleplate.

PREPARATION

  1. Check for textile care symbols ( ).
  2. Iron fabrics needing low temperatures first, then those that need medium temperatures , and finish with those needing high temperatures .

FILLING

You may use the iron with tap-water, but if you live in a hard water area, you should use distilled water (not chemically descaled or softened water).
If you buy distilled water, check that it’s suitable for use in irons.

  1. Unplug the iron.
  2. Set the temperature control to •. Set the steam control to .
  3. Open the cover.
  4. Pour slowly, to let the air in the reservoir escape, otherwise you’ll cause an air lock and the water will overflow.
  5. Don’t fill past max, or water will escape in use.
  6. Wipe up any spillage.

SWITCH ON

  1. Set the temperature control to •. Set the steam control to .
  2. Sit the iron on its heel.
  3. Put the plug into the power socket (switch the socket on, if it’s switchable).
  4. Turn the temperature control to bring the setting you want next to the mark. The light will come on.
  5. When the iron reaches the temperature you set, the light will go off. It’ll then cycle on and off as the thermostat operates to maintain the temperature.

TEMPERATURE SETTING GUIDE

Label marking Dot setting
cool – nylon, acrylics, polyester
warm – wool, polyester mixtures ••
hot – cotton, linen •••/max
do not iron

If the instructions on the fabric label differ from this guide, follow the instructions on the label.

STEAM IRONING

  1. If you intend to use steam, the temperature setting must be or higher.
  2. Set the steam control to the setting you want ( = no steam, = high).
  3. Wait till the light goes off, then start ironing.

STEAM IRONING

  1. If you intend to use steam, the temperature setting must be S or higher.
  2. Set the steam control to the setting you want (S = no steam, # = high).
  3. Wait till the light goes off, then start ironing.

SHOT OF STEAM
If you intend to use steam the temperature control must be at or higher.

  1. Lift the iron off the fabric.
  2. Press the button.
  3. Leave 4 seconds between shots, to let the temperature build up.

DRY IRONING
If you’re going to be dry ironing for 20 minutes or more, empty the reservoir first, to avoid spontaneous bursts of steam.

  1. Set the steam control to .
  2. Wait till the light goes off, then start ironing.

VERTICAL STEAMING

Remove wrinkles from hanging clothes, hanging curtains, and furnishing fabrics.

  • Check that there’s adequate ventilation behind the fabric, otherwise moisture may build up, causing mildew.
  • Check that there’s nothing behind the fabric that may be damaged by the steam.
  • Check that pockets, turn-ups, and cuffs are empty.
  • Check that there’s water in the reservoir.
    1. Set the temperature control to max. Set the steam control to .
    2. Hold the iron close to (but not touching) the fabric.
    3. Press the ~ button (you’re using the “shot of steam” function vertically).
    4. Leave 4 seconds between shots, to let the temperature build up.

AUTO SHUT-OFF
If the iron is motionless, it will switch off after about 30 seconds lying down, or about 8 minutes if it’s upright.
The iron will beep and the light will flash continuously until you move the iron.
To switch on again, lift it up, tilt it forward, then sit it upright to return to operating temperature. No settings are lost during auto shut-off.
AFTER USE

  1. Set the temperature control to •. Set the steam control to .
  2. Unplug the iron.
  3. Open the cover.
  4. Hold it over a sink, turn it upside down, and drain the water from the reservoir, via the water inlet.
  5. Close the cover.
  6. Sit the iron on its heel.
  7. Leave it to cool down completely.
  8. When it’s cold, wipe off any moisture, and wind the cable round the heel.
  9. Store the iron on its heel, to avoid corrosion and damage to the soleplate.

SELF CLEAN

To avoid scale build up, use the self clean function at least monthly in normal water areas, more often in hard water areas.
Products returned under guarantee with faults due to scale will be subject to a repair charge.
You’ll need a basin or a large bowl to catch the water coming out of the soleplate.

  1. Fill the reservoir to the max mark.
  2. Set the temperature control to max. Set the steam control to S.
  3. Sit the iron on its heel.
  4. Put the plug into the power socket and wait till the light goes out.
  5. Hold the iron over the basin or bowl with the soleplate down.
  6. Press the , and hold it down.
  7. Gently move the iron to and for, over the basin or bowl.
  8. Water and steam will wash scale and dust through the soleplate, and into the sink.
  9. When the reservoir is empty, release the button.

ANTI-SCALE
The anti-scale agent incorporated in the iron helps prevent the build-up of scale.
Don’t use a descaling solution, or you’ll destroy the anti-scale.
RECYCLING
To avoid environmental and health problems due to hazardous substances, appliances and rechargeable and non-rechargeable batteries marked with one of these symbols must not be disposed of with unsorted municipal waste. Always dispose of electrical and electronic products and, where applicable, rechargeable and non-rechargeable batteries, at an appropriate official recycling/collection point.

26340-56 220-240V~50/60Hz 2600-3100Watts
26340-56 220-240В~50/60Гц 2600-3100 Вт
T22-9002541

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Russell Hobbs User Manuals

Related Manuals