BN-LINK Outdoor Indoor Wireless Remote Control User Manual
- June 9, 2024
- BN-LINK
Table of Contents
BN-LINK Outdoor Indoor Wireless Remote Control
FEATURES
- Easily controlled by the remote control from up to 100 feet in line-of-sight.
- Separate on and off buttons on the remote control.
- Outlets will remain powered off after a power outage to save energy.
- Power output up to 1875W at 125V(60Hz).
- Low power consumption, reduces energy use and extends product life by up to 15%.
- Manual pairing and unpairing.
SETUP
- Install one 12V /23A battery in the remote control’s battery compartment, making sure the polarity of the battery is correct.
- Plug the receiver into an outlet and plug a device or appliance into an outlet of the receiver.
- Press the ON or OFF button on the remote control to operate the receiver outlet.
NOTES
- Regularly change the battery in the remote control for the best performance. If you find the outlet switch is not responding or the LED indicator on the remote control becomes dim, the battery should be replaced. Always dispose of old batteries properly with the environment.
- Make sure the battery and outlet are installed firmly and correctly for safe operation.
- The outlet switch is for indoor and outdoor use
- Use only in well-ventilated areas.
- Do not exceed the maximum load current of 15A(Approximately 1875W).
PROGRAMMING THE OUTLETS
Notes: The outlet is pre-programmed for immediate use, but the configuration can be customized to meet your needs.
To pair the receiver to the transmitter
- Plug the receiver outlet into a power outlet.
- Press and hold the ON/OFF button on the receiver outlet for 3 seconds and the LED indicator will start flashing slowly.
- Release the ON/OFF button on the receiver and press ON or OFF button on the transmitter to pair the transmitter to the receiver. To quit the paring mode, press and hold the
ON/OFF button on the receiver for 3 seconds until the LED indicator goes off.
RESETTING AN OUTLET
Should you wish to unpair an outlet receiver from the remote, or if your outlet is unresponsive to the remote, the outlet can be reset following below steps.
To unpair receiver from transmitter
- Plug the receiver outlet to a power outlet.
- Press and hold the ON/OFF button on the receiver outlet for 3 seconds, the LED indicator will start flashing slowly. Keep holding the button until the LED indicator flashes fast and then goes off.
- The receiver is now unpaired from the transmitter.
TROUBLESHOOTING
In the case that the outlet receiver does not respond to the remote control, please follow the steps given below to resolve the issue:
- Check to see if the battery of the remote is low and needs replacement.
- Make sure that the outlet receiver is correctly placed in the power socket.
- Make sure that the outlet receiver is used in an area with proper air circulation to avoid overheating.
- Reset and program the outlet
TECHNICAL DATA
- Voltage …………………………… 125V~60Hz
- Resistive ………………………. 15A 1875W
- Tungsten ………………………. 10A 1250W
- Transmission frequency ……. 433.92MHz
- Remote battery ………………………. 12V /23A
CENTURY PRODUCTS INC. 3545 Granada Ave El Monie Ca 91731
Custom Service Assistance: 1.909.592.1881
E-mail: supporl@bn-link.com
Http://www.bn-link.com
Hours: 9AM – 5PM PST, Mon – Fri Designed in California Made in China
FAQs
How does the remote control work?****
The remote control sends a wireless signal to the receiver. The receiver then turns on or off the outlet.
Can I use the remote control to turn on and off other electrical devices?****
Yes, you can turn on and off any electrical device that is plugged into the outlet.
Does this product work with 220V outlets?****
No, this product only works with 120V outlets.
What is the benefit of wireless remote control?****
You can carry or keep a wireless remote control in your car kit. It gives you complete control over the equipment or gadget from any location, enabling you to use it in any situation. Because of this, you may accomplish more in the same amount of time while also saving a lot of time.
How does wireless remote control work?****
The transmitter that is built within the handset is what makes remote controls function. When a button is pressed, this transmitter emits a continuous stream of infrared light pulses. The receiving antenna can determine what command to execute thanks to the infrared light’s distinctive pattern, which is specific to that button.
What is the purpose of remote control?****
A remote control, commonly referred to as a remote or clicker, is an electrical gadget used to wirelessly and remotely control another device. A remote control can be used to operate consumer electronics, including television sets, DVD players, and other home appliances.
Who invented the wireless remote control?****
The first useful, wireless television remote control was created by Robert Adler. Before the development of infrared technology in the 1980s, Adler’s device, marketed by Zenith in 1956 as the “Space Command,” was sold alongside more than nine million televisions. Adler, who was born in Vienna, Austria, in 1913, holds a Ph.
Why is my wireless remote not working?****
Verify that none of the remote’s buttons are stuck or jammed. The battery connectors for the remote control could be unclean. Place the batteries back into the remote control after removing them and using a cotton bud or soft cloth to wipe the remote control terminals with a tiny solution of alcohol.
How does remote control improve our lives?****
The usage of a remote control has the apparent advantage of being easier on the body than traditional, manual machine operation. It’s considerably simpler to use your fingers or press a button to operate the machinery.
What type of energy does a remote control use?****
An average remote control for a television emits infrared energy with a wavelength of about 940 nanometers. Some digital and cell phone cameras are sensitive to that wavelength of radiation, despite the fact that you cannot “see” the light emanating from a remote.
What are the methods of remote control?****
Sending signals using infrared light (like a TV remote), visible light, radio waves, wires, fibre optics, or sound waves can all be used for remote control. Like visible light and laser signals, the standard television remote uses infrared technology and needs a line-of-sight connection.
What are the components of remote control?****
An RF remote control’s fundamental parts are buttons allowing the user to input commands, an MCU to convert those commands into digital messages, an RF transmitter (RF TX) to modulate and send the message, an antenna, and a battery to power the device.
Video
Download PDF Link;BN-LINK Outdoor Indoor Wireless Remote Control pdf
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>