mimosa A6 5 and 6 GHz Fixed Wireless WiFi 6E PTMP Access Point User Manual

June 9, 2024
mimosa

A6 5 and 6 GHz Fixed Wireless WiFi 6E PTMP Access Point
User Manualmimosa A6 5 and 6 GHz Fixed Wireless WiFi 6E PTMP Access
Point

5 & 6 GHz Fixed Wireless WiFi 6E PTMP Access Point

A6 5 and 6 GHz Fixed Wireless WiFi 6E PTMP Access Point

Additional Required & Optional Items

  • 10 AWG (5.26 mm2 ) ground cable with pre-terminated ring terminal
  • Small flat head type screwdriver (for direct 48VDC power terminal)
  • 15, 13 and 10 mm socket or adjustable wrench for mounting assembly
  • Power Option A: 18 AWG 2-pin wire for direct power wiring 48VDC input
  • Power Option B: Shielded CAT6/6A & compatible PoE injector (refer to A6 datasheet specifications)
  • Optional: SFP+ fiber (non-copper) module and preferred optical cabling A6
  • Optional: 19mm (3/4”) flexible conduit/hose tubing and hose-clamps for additional cable protection
  1. Mounting
    Tightly attach the supplied sliding & pivot brackets to mounting pole in desired up or downhill orientation.mimosa A6 5 and 6 GHz Fixed Wireless WiFi
6E PTMP Access Point - fig

  2. Grounding
    Attach 10 AWG ground wire with pre-terminated ring terminal to the grounding screw.mimosa A6 5 and 6 GHz Fixed Wireless WiFi 6E PTMP Access Point -
fig1

  3. Dedicated 48VDC Power
    • Thread an 18 AWG 2-pin cable through one the supplied IP67 gland/cap.
    • Strip the wire jackets approximately 6-7mm, and attach to the supplied power connector terminals (+/- indicated in diagram). Tighten the terminal screws. Note:  reverse polarization will not damage the device, however proper +/- wiring is required to apply power.
    • Insert and snap the power plug and cable into the PWR port.
    • Attach and tighten gland, attach the rubber insert to the cable, pushing it into the gland, then tighten the cap.mimosa A6 5 and 6 GHz Fixed Wireless
WiFi 6E PTMP Access Point - fig2

  4. Gigabit Ethernet or PoE Insert a shielded CAT6/6A Ethernet cable through the IP67 gland/cap. Connect the cable to ETH port. Attach and tighten gland, attach the  rubber insert to the cable, pushing it into the gland, then tighten the cap.
    PoE powering is optional and can be used as primary or as redundant/backup power to the 48VDC. Ethernet connection is NOT required if SFP+ optical fiber is being used. mimosa A6 5 and 6 GHz Fixed Wireless WiFi 6E PTMP Access
Point - fig3

  5. Optional Flexible Conduit
    The provided IP67 gland caps are designed to accommodate optional 19mm (3/4”) outdoor hose conduit/tubing, and hose-type clamps to secure the tubing. Both can  be procured at most hardware stores. mimosa A6 5 and 6 GHz Fixed
Wireless WiFi 6E PTMP Access Point - fig4

  6. Optional SFP+ Optical Fiber
    Two SFP+ ports are provided to accommodate standard SFP+ 10 Gbps optical modules, and bult-in switching between the ports for interconnectivity to other devices. Visit support for additional SFP+ module and configuration information.

  7. Seal All Unused Ports
    For any unused ports, tightly screw in the supplied port sealing caps to maintain environmental integrity of the system.

  8. Unlock and Configure
    Visit start.mimosa.co to unlock the device.

Warnings, Warranty, Compliance & Regulatory Statements
Mimosa by Airs pan (“Mimosa”) products are provided by Airs pan Networks Inc. (“Airs pan”).

Export Control
These commodities, technology, or software were exported from the United States in accordance with the Export Administration Regulations. Diversion contrary to U.S. law is prohibited.
Important Safety and Handling Information
Failure to follow any of the safety instructions in this guide, instructions on any Airs pan provided packaging, and heed WARNINGS (indicated by ), could result in fire,  electric shock, other injury or death, and incur damage to this product or other property and void the product’s Limited Warranty.
There are no End User serviceable parts inside the equipment.
Read all operating and safety instructions contained herein and accompanying the product as provided by Air span:
Electrical Safety Information
Do not operate this product in any location that can be submerged by water.
Do not install or maintain this product during the presence of an electrical storm to avoid risk of electric shock from lightning. Failure to ground the device  according to the  included instructions using shielded CAT6/6A Ethernet cabling could lead to serious injury or death.
Installation of the product must comply with local and national electrical codes.
Power specifications for connected devices are indicated on the device’s own label or documentation. Connecting to any power source that does not meet the voltage,  frequency and current requirements listed may damage the power supply or product, and pose a fire hazard.

Mandatory Grounding Instructions
IMPORTANT: Failure to properly ground the device using the following instructions will violate the limited warranty conditions in this document.
Required Step 1- Direct Grounding on the Device:
A minimum grounding wire of 10 AWG (5.26 mm2 ) with a secured grounding terminal, and shorter in length than 1 meter is required. It is NOT supplied with the product.

  1. Ensure that NO power is being supplied to the product.
  2. Locate the Ground point screw next to the Ground icon on the device
  3. Remove the provided Ground Screw
  4. Thread the ground wire terminal and ground wire meeting the above specifications over the screw removed in the previous step.
  5. Replace and tighten the screw with the threaded ground terminal and cable at the product Ground point.
  6. Secure the other end of the grounding cable to the properly grounded structure (pole, tower, mast, etc.) meeting local and national electrical regulations and codes.

End User Product Warranty
The product is warranted against defects in material, and workmanship for a period of twenty four (24) months from the date of first unlock of the product. Please go to  www.mimosa.co/warranty to determine whether your product is in warranty.
The sole responsibility of Airs pan under this warranty shall be limited to the repair or replacement of in-warranty defective product, at Airs pan’s sole option.
Out of warranty products shipped to Airs pan will not be returned.
This warranty does not cover costs associated with the removal and/or reinstallation of the product for repair nor for any parts that are readily replaced in normal use.
Airs pan or its designated partner will repair or replace product found to be defective during the defined warranty period.
The End User is responsible for delivering defective product in accordance with the Return Material Authorization (RMA) processes published at www.mimosa.co/legal/RMA

Limitation of Warranty

The product warranty is invalidated if the RMA product is altered or otherwise tampered with in a manner that modifies the product from its original shipping configuration  and/or form factor, and could violate the End User’s authority to operate the equipment, unless said activity was performed by or with the written authorization of an  Air span representative.

Modifications include:
(a) External surfaces that have been painted, labeled, or otherwise modified from the original shipping condition.
(b) Modifications of the product with third party hardware, firmware, and/or software.
(c) Any product subjected to abnormal physical or electric stress, including, but not limited to, lightning strikes, negligence, accident, or misuse.
(d) Any product damaged due to incorrect installation, including, but not limited to, improper product mounting, cabling meeting minimum requirements in this manual,  cabling defects or connection to power.
(e) Failure induced by connected third party products.
Installing the product outdoors without the use of minimum CAT6/6A shielded Ethernet cable, improper grounding, or failure to ground the product as instructed in this  guide will void the End User Product warranty.

Disclaimer
EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN,AIRSPAN AND ITS SUBSIDIARIES, LICENSORS AND AFFILIATES ( COLLECTIVELY,  “AIRSPAN”), AND ANY THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND AND HEREBY DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, BUT  NOT LIMITED TO, ANY REPRESENTATIONS OR WARRANTIES OF DESIGN, MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES. YOU ACKNOWLEDGE THAT  NEITHER AIRSPAN NOR ITS THIRD PARTY PROVIDERS CONTROL YOUR EQUIPMENT OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES PROVIDED BY AIRSPAN MAY BE SUBJECT TO LIMITATIONS,  INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. AIRSPAN AND  ANY THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION,  PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING.
IN ADDITION, AIRSPAN  MAKES NO WARRANTY OR UNDERTAKING, AND MAKES NO REPRESENTATION OF ANY KIND THAT THE LICENSED PRODUCTS WILL MEET  OUR REQUIREMENTS, ACHIEVE ANY INTENDED RESULTS, BE COMPATIBLE OR WORK WITH ANY OTHER APPLICATIONS, SYSTEMS OR SERVICES, OPERATE WITHOUT INTERRUPTION, MEET ANY PERFORMANCE OR RELIABILITY STAN- DARDS, BE ERROR FREE OR THAT ANY  ERRORS OR DEFECTS CAN OR WILL BE CORRECTED, OR THAT THE LICENSED PRODUCTS ARE NOT VULNERABLE TO FRAUD OR UNAUTHORIZED USE.
Limitation of Liability
EXCEPT TO THE EXTENT PROHIBITED BY THE LAWS IN YOUR JURISDICTION, IN NO EVENT WILL AIRSPAN OR ITS SUPPLIERS OR LICENSORS BE LIABLE FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), NOR FOR DAMAGES BASED ON UNAUTHORIZED USE OR ACCESS, ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL AIRSPAN, ITS SUPPLIERS’ OR ITS LICENSORS’ DIRECT LIABILITY EXCEED THE VALUE OF THE LICENSED PRODUCTS GIVING RISE TO SUCH LIABILITY. THESE LIMITATIONS SHALL APPLY NOTHWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED REMEDY. IN NO EVENT SHALL AIRSPAN BE RESPONSIBLE FOR DAMAGES OR CLAIMS OF ANY NATURE OR DESCRIPTION RELATING TO NETWORK PERFORMANCE, INCLUDING COVERAGE, YOUR SELECTION OF AIRSPAN PRODUCTS FOR YOUR PARTICULAR APPLICATION AND/OR FAILURE OF AIRSPAN PRODUCTS TO MEET GOVERNMENT OR REGULATORY REQUIREMENTS.
Some legal jurisdictions do not allow exclusions of implied warranties or conditions, or for the exclusion or limitation of liability for incidental or consequential damages, so  the above exclusion may not apply to you.
You may have other rights specific to your legal jurisdiction. EXCEPT TO THE EXTENT ALLOWED BY THE LAW OF YOUR JURISDICTION, THESE  WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, ANY MANDATORY STATUTORY RIGHTS APPLICABLE  TO YOU IN THE LICENSE OF ANY EMBEDDED SOFTWARE. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to  any transactions regarding the sale of the Products.

FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for  human contact during the normal operation is minimized. In order to avoid the possibility of exceeding the FCC radio frequency exposure limit, human proximity to the  antenna should be more than 3m.
When mounting the radio antenna, in accordance with the Part 15 UNII1 band requirements, the antenna must not exceed 125 mW (21 dBm) e.i.r.p. at any elevation angle  above 30 degrees as measured from the horizon).
Important: Changes or modifications to this product not authorized by Mimosa Networks, Inc. could void the electromagnetic compatibility (EMC) and wireless compliance  and negate your authority to operate the product. The information in this guide may change without notice. The manufacturer assumes no responsibility for any errors that  may appear in this guide.

Industry Canada
This Class A digital apparatus complies with Canadian CAN ICES-3(A).
Canada.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry  Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated power (e.i.r.p.) is
not more than that necessary for successful communication.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference,  and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.

Australia & New Zealand
Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
European Compliance Statement
CE Marking on this product represents that this product complies with all requirements that are applicable to it.

Europe EU Declaration of Conformity
This device can be used in the European Community. A copy of the EU Declaration of Conformity is available at: www.mimosa.co/compliance.
Hereby, Air span Networks Inc. declares that this Airs pan Networks Inc. device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.

RoHS & WEEE Compliance
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE).
This document contains important information for users with regards to the proper disposal and recycling of Air span Networks Inc. products. Consumers are required to  comply with this notice for all electronic products bearing this symbol.
Environmental Information for Customers in the European Union
European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal  waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other  electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent  potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local  authorities, waste disposal service, or the shop where you purchased the product.

UNLOCK REQUIRED
This device requires unlocking prior to use.
For all unlocking instructions and options prior to onsite
installation, please visit: mimosa.co/start

For instructions, videos and help
visit: support.mimosa.co

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals