mimosa C6x Flexible 5GHz WiFi 6 PTMP Client and PTP Radio User Manual

C6x Flexible 5GHz WiFi 6
PTMP Client and PTP Radio

User Manual

UNLOCK REQUIRED
This device requires unlocking prior to use. For all unlocking instructions and options prior to onsite installation, please visit:

Default mode of the C6x is as PTMP CPE. If PTP is required, contact your channel sales representative for purchasing a PTP license key.
PTP mode regulations vary by country and may not be allowed in all frequency bands.

Required Items

• Mimosa N5-X series antenna
• Minimum 10 AWG (5.26 mm2 ) ground cable with pre-terminated ring terminal
• Mimosa Gigabit NID (recommended)
• Small flat head type screwdriver
• 50V Mimosa by Airs pan PoE, or other 24-56VDC passive isolated PoE rated 20W or higher.

1. Attach Antenna
   Mount the antenna by clockwise twisting into the radio threaded collar. Hand tighten until the O-ring seal is seated in the collar.Make sure the indicator dot on the antenna is aligned with the set screw as shown in the diagram below, then tighten the set screw.If you are using the radio standalone without an antenna, remove the set screw to allow drainage of any accumulated moisture in the threaded area.

2. Mount
   Using 2 hose clamp type pole straps, attach the C6x to the desired mounting pole. If elevation adjustment is needed, a Mimosa Flex mount XL or J-Mount is suggested.

3. Grounding
   Attach ground wire (not included) to the integrated grounding screw.

4. Connect Ethernet
   Connect a shielded CAT6/6A Ethernet cable (not included) to the device, inserting it through the M25 cable sealing gland components and tighten by hand.

5. Unlock and Configure
   Visit start.mimosa.co to unlock the device.

Warnings, Warranty, Compliance & Regulatory Statements

Mimosa by Arpan (“Mimosa”) products are provided by Arpan Networks Inc. (“Arpan”).

Export Control
These commodities, technology, or software were exported from the United States in accordance with the Export Administration Regulations.
Diversion contrary to U.S. law is prohibited.

Important Safety and Handling Information
Failure to follow any of the safety instructions in this guide, instructions on any Airs pan provided packaging, and heed WARNINGS (indicated by ), could result in fire, electric shock, other injury or death, and incur damage to this product or other property and  void the product’s Limited Warranty.
There are no End User serviceable parts inside the equipment. Read all operating and safety instructions contained herein and accompanying the product as provided by Airs pan:

Electrical Safety Information

Do not operate this product in any location that can be submerged by water.
Do not install or maintain this product during the presence of an electrical storm to avoid risk of electric shock from lightning. Failure to ground the device according to the included instructions using shielded CAT6/6A Ethernet cabling could lead to serious injury or death.
Installation of the product and antenna, configuration of product with antenna must comply with local and national electrical codes.
Power specifications for connected devices are indicated on the device’s own label or documentation. Connecting to any power source that does not meet the voltage, frequency and current requirements listed may damage the power supply or product, and pose a fire hazard.

Mandatory Grounding Instructions

IMPORTANT: Failure to properly ground the device using the following instructions will violate the limited warranty conditions in this document.
Required Step 1- Direct Grounding on the Device:
A minimum grounding wire of 10 AWG (5.26 mm2 ) with a secured grounding terminal, and shorter in length than 1 meter is required. It is NOT supplied with the product.

1. Ensure that NO power is being supplied to the product.
2. Locate the Ground point screw next to the Ground icon on the device
3. Remove the provided Ground Screw
4. Thread the ground wire terminal and ground wire meeting the above specifications over the screw removed in the previous step.
5. Replace and tighten the screw with the threaded ground terminal and cable at the product Ground point.
6. Secure the other end of the grounding cable to the properly grounded structure (pole, tower, mast, etc.) meeting local and national electrical regulations and codes.

Required Step 2 – Use Mimosa Gigabit NID for Grounding via CAT6/6A Shielded Ethernet:
The Mimosa Gigabit NID is required to provide enhanced Electrostatic Discharge (ESD) protection for devices and the premises during electrical events.
To prevent device damage, avoid ground voltage potential difference between the device integrated ground and the Gigabit NID ground. Failure to follow all instructions provided with the separately sold Mimosa Gigabit NID will violate the product warranty and could lead to serious injury or death.

End User Product Warranty

Mimosa products purchased from Airs pan are warranted against defects in material, and workmanship for a period of either (i) twelve (12) months from the date of activation, or (ii) thirty-six (36) months from the original date of shipment, whichever is earlier.  Please go to www.mimosa.co/warranty to determine whether your product is in warranty.
The sole responsibility of Airs pan under this warranty shall be limited to the repair or replacement of in-warranty defective product, at Airspan’s sole option.
Out of warranty products shipped to Airspan will not be returned.
This warranty does not cover costs associated with the removal and/or reinstallation of the product for repair nor for any parts that are readily replaced in normal use.
Airspan or its designated partner will repair or replace product found to be defective during the defined warranty period.
The End User is responsible for delivering defective product in accordance with the Return Material Authorization (RMA) processes published at www.mimosa.co/legal/RMA

Limitation of Warranty

The product warranty is invalidated if the RMA product is altered or otherwise tampered with in a manner that modifies the product from its original shipping configuration and/or form factor, and could violate the End User’s authority to operate the equipment, unless said activity was performed by or with the written authorization of an Airspan representative.

Modifications include:
(a) External surfaces that have been painted, labeled, or otherwise modified from the original shipping condition.
(b) Modifications of the product with third party hardware, firmware, and/or software.
(c) Any product subjected to abnormal physical or electric stress, including, but not limited to, lightning strikes, negligence, accident, or misuse.
(d) Any product damaged due to incorrect installation, including, but not limited to, improper product mounting, cabling, cabling defects or connection to power.
(e) Failure induced by connected third party products.
Installing the product outdoors without the use of minimum CAT6/6A shielded Ethernet cable, improper grounding, or failure to ground the product as instructed in this guide will void the End User Product warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, AIRSPAN AND ITS SUBSIDIARIES, LICENSORS AND AFFILIATES ( COLLECTIVELY, “AIRSPAN”), AND ANY THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND AND HEREBY DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY REPRESENTATIONS OR WARRANTIES OF DESIGN, MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES. YOU ACKNOWLEDGE THAT NEITHER AIRSPAN NOR ITS THIRD PARTY PROVIDERS CONTROL YOUR EQUIPMENT OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES PROVIDED BY AIRSPAN MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. AIRSPAN AND ANY THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING.
IN ADDITION, AIRSPAN MAKES NO WARRANTY OR UNDERTAKING, AND MAKES NO REPRESENTATION OF ANY KIND THAT THE LICENSED PRODUCTS WILL MEET YOUR REQUIREMENTS, ACHIEVE ANY INTENDED RESULTS, BE COMPATIBLE OR WORK WITH ANY OTHER APPLICATIONS, SYSTEMS OR SERVICES, OPERATE WITHOUT INTERRUPTION, MEET ANY PERFORMANCE OR RELIABILITY STANDARDS, BE ERROR FREE OR THAT ANY ERRORS OR DEFECTS CAN OR WILL BE CORRECTED, OR THAT THE LICENSED PRODUCTS ARE NOT VULNERABLE TO FRAUD OR UNAUTHORIZED USE.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY THE LAWS IN YOUR JURISDICTION, IN NO EVENT WILL AIRSPAN OR ITS SUPPLIERS OR LICENSORS BE LIABLE FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), NOR FOR DAMAGES BASED ON UNAUTHORIZED USE OR ACCESS, ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL AIRSPAN, ITS SUPPLIERS’ OR ITS LICENSORS’ DIRECT LIABILITY EXCEED THE VALUE OF THE LICENSED PRODUCTS GIVING RISE TO SUCH LIABILITY. THESE LIMITATIONS SHALL APPLY NOTHWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED REMEDY. IN NO EVENT SHALL AIRSPAN BE RESPONSIBLE FOR DAMAGES OR CLAIMS OF ANY NATURE OR DESCRIPTION RELATING TO NETWORK PERFORMANCE, INCLUDING COVERAGE, YOUR SELECTION OF AIRSPAN PRODUCTS FOR YOUR PARTICULAR APPLICATION AND/OR FAILURE OF AIRSPAN PRODUCTS TO MEET GOVERNMENT OR REGULATORY REQUIREMENTS.
Some legal jurisdictions do not allow exclusions of implied warranties or conditions, or for the exclusion or limitation of liability for incidental or consequential damages, so the above exclusion may not apply to you. You may have other rights specific to your legal jurisdiction. EXCEPT TO THE EXTENT ALLOWED BY THE LAW OF YOUR JURISDICTION, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, ANY MANDATORY STATUTORY RIGHTS APPLICABLE TO YOU IN THE LICENSE OF ANY EMBEDDED SOFTWARE. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to any transactions regarding the sale of the Products.

FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact during the normal operation is minimized. In order to avoid the possibility of exceeding the FCC radio frequency exposure limit, human proximity to the antenna should be more than 3m.
When mounting the radio antenna, in accordance with the Part 15 UNII1 band requirements, the antenna must not exceed 125 mW (21 dBm)
e.i.r.p. at any elevation angle above 30 degrees as measured from the horizon).

Important: Changes or modifications to this product not authorized by Mimosa Networks, Inc. could void the electromagnetic compatibility (EMC) and wireless compliance and negate your authority tooperate the product. The information in this guide may  change without notice. The manufacturer assumes no responsibility for any errors that may appear in this guide.
Industry Canada
This Class A digital apparatus complies with Canadian CAN ICES-3(A).

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and  its gain should be so chosen that the equivalent isotropic ally radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.

Australia & New Zealand
Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

European Compliance Statement
**** CE Marking on this product represents that this product complies with all requirements that are applicable to it.

Europe EU Declaration of Conformity
This device can be used in the European Community. A copy of the EU Declaration of Conformity is available at: www.mimosa.co/compliance.

RoHS & WEEE Compliance

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE).
**** This document contains important information for users with regards to the proper disposal and recycling of Airspan Networks Inc.
products. Consumers are required to comply with this notice for all electronic products bearing this symbol.
English – Environmental Information for Customers in the European Union
European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular  household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential  negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.

For instructions, videos and help visit: support.mimosa.co
Para oftener instructions,: setup.mimosa.co

References

• Mimosa
• Mimosa Networks
• Mimosa
• Mimosa Networks
• Mimosa Networks
• Mimosa Networks

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>