ELKRON IT3000-2G GSM-GPRS Interface Instruction Manual
- June 9, 2024
- ELKRON
Table of Contents
ELKRON IT3000-2G GSM-GPRS Interface Instruction Manual
Interface 2G
Complete manual
LEGEND
**A| | ● SMA antenna connector
****B| ** REG| ● LED mobile phone network connection status
**C**| | ● SIM card slot (nano SIM size)
TECHNICAL FEATURES
Nominal supply voltage| | 13,8 V⎓
Operating voltage| | 10 ÷ 14,5 V⎓
**** Rated absorbed current| ● Stand-by| 10 mA (13,8 V⎓)
Transmission (max)| 200 mA (13,8 V⎓)
Output power (max)| Class 4Class 1| (2W@850/900 MHz) (1W@1800/1900MHz)
Operating frequency| | 850/900/1800/1900 MHz
**** GPRS data transmission| In reception up to| 85,6 Kbps
In transmission up to| **** 42,8 Kbps
SIM card format| | Nano-SIM
Dimensions (L x H)| | 40 x 70 mm
Classification according to EN50136-2| | **** SP2-SP4, DP1-DP2
This document contains only essential information about the product. Refer to the manuals of the MP3000 panel for more information.
GENERAL DESCRIPTION
The IT3000-2G is an interface for connecting the MP3000 control panel to 2G (GSM/GPRS) communication networks. The interface can play back pre-recorded telephone messages, transmit data in GPRS mode, recognise DTMF tones, and send and receive text messages. It can also establish communication with a remote alarm receiving station (management unit) using the SIA-IP protocol a data channel. This allows connection to Elkron Cloud for remote management of the control panel. The interface is housed directly on the CPU board of the control panel.
-
ASSEMBLY
IMPORTANT! Insert the interface only when the control panel is not powered (mains and battery disconnected). Place the board in the OPT3 position (recommended) of the CPU by carefully aligning both connectors, applying adequate pressure until they engage. OPT1/OPT2 positions can be used as an alternative. -
ANTENNA CONNECTION
Place the antenna (included) in the specific location at the top left of the box and connect the SMA connector of the antenna to the SMA connector of the interface.
IMPORTANT!
It is recommended to tighten the SMA antenna connector on the interface
firmly, but without damaging it. Tightening torques 0.9Nm.
SIM CARD INSERTION IMPORTANT!
Before inserting the SIM card into the GSM module, check that it is active and
without any additional paid options that would use up the credit
unnecessarily. Insert the SIM card only when the control panel is not powered
(mains and battery disconnected). The SIM card (Nano-SIM format) is simply
inserted into the specific housing Push it in until you hear a slight click.
ACCESSORIES
ANT 2/4G BM: metal cabinet antenna with SMA-M connector compatible with the
IT3000-GSM and IT3000-4G modules ANT 2/4G HG: high gain antenna, cable length
5 metres with SMA-M connector. Compatible with IT3000-GSM and IT3000-4G
modules.
EN50136-2 COMPLIANCE
The line control must be enabled with a time not exceeding 25hrs (SP2) or 3
min (SP4) to ensure compliance with EN50136-2 in the configuration of the
interface. DP1 guaranteed with: IT3000-2G primary interface and IT3000-PSTN
alternate interface DP2 guaranteed with: IT3000-2G primary interface and
alternative LAN connection with 30 min periodic test.
SIMPLIFIED EU DECLARATION OF CONFORMITY
The manufacturer, Urmet S.p.A., hereby declares that the wireless device: GSM
interface Mod. IT3000-2G complies with Directive 2014/53/EU. The complete text
of the EU declaration of conformity is available at the following link:
www.elkron.com.