audizio 102.427 Corno Retro DAB+ Radio Instruction Manual

: June 9, 2024
: audizio

Table of Contents

Introduction
Safety Instruction
UNPACKING INSTRUCTION
POWER SUPPLY
CONTROLS AND CONNECTION
GETTING STARTED
DAB +
FM RADIO
BT PLAYBACK
AUX IN
ALARM SETTING
TECHNICAL SPECIFICATION
CUSTOMER SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

audizio 102.427 Corno Retro DAB+ Radio

Introduction

Congratulations to the purchase of this Audizio product. Please read this manual thoroughly prior to using the unit in order to benefit fully from all features.
Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock. Keep the manual for future reference.

Safety Instruction

Prior to using the unit, please ask advice from a specialist. When the unit is switched on for the first time, some smell may occur. This is normal and will disappear after a while.
The unit contains voltage carrying parts. Therefore do NOT open the housing.
Do not place metal objects or pour liquids into the unit This may cause electrical shock and malfunction.
Do not place the unit near heat sources such as radiators, etc. Do not place the unit on a vibrating surface. Do not cover the ventilation holes.
The unit is not suitable for continuous use.
Be careful with the mains lead and do not damage it. A faulty or damaged mains lead can cause electrical shock and malfunction.
When unplugging the unit from a mains outlet, always pull the plug, never the lead.
Do not plug or unplug the unit with wet hands.
If the plug and/or the mains lead are damaged, they need to be replaced by a qualified technician.
If the unit is damaged to such an extent that internal parts are visible, do NOT plug the unit into a mains outlet and DO NOT switch the unit on. Contact your dealer. Do NOT connect the unit to a rheostat or dimmer.
To avoid fire and shock hazard, do not expose the unit to rain and moisture.
All repairs should be carried out by a qualified technician only.
Connect the unit to an earthed mains outlet (220- 240Vac/50Hz) protected by a 10-16A fuse.
During a thunderstorm or if the unit will not be used for a longer period of time, unplug it from the mains. The rule is: Unplug it from the mains when not in use.
If the unit has not been used for a longer period of time, condensation may occur. Let the unit reach room temperature before you switch it on. Never use the unit in humid rooms or outdoors.
To prevent accidents in companies, you must follow the applicable guide lines and follow the instructions.
Do not repeatedly switch the fixture on and off. This shortens the life time.
Keep the unit out of the reach of children. Do not leave the unit unattended.
Do not use cleaning sprays to clean switches. The residues of these sprays cause deposits of dust and grease. In case of malfunction, always seek advice from a specialist.
Do not force the controls.
This unit is with speaker inside which can cause magnetic field. Keep this unit at least 60cm away from computer or TV.
If this product have a built-in lead-acid rechargeable battery. Please recharge the battery every 3 months if you are not going to use the product for a long period of time. Otherwise the battery may be permanently damaged.
If the battery is damaged please replace with same specifications battery. And dispose the damaged battery environment friendly.
If the unit has fallen, always have it checked by a qualified technician before you switch the unit on again.
Do not use chemicals to clean the unit. They damage the varnish. Only clean the unit with a dry cloth.
Keep away from electronic equipment that may cause interference.
Only use original spares for repairs, otherwise serious damage and/or dangerous radiation may occur.
Switch the unit off prior to unplugging it from the mains and/or other equipment. Unplug all leads and cables prior to moving the unit.
Make sure that the mains lead cannot be damaged when people walk on it. Check the mains lead before every use for damages and faults!
The mains voltage is 220-240Vac/50Hz. Check if power outlet match. If you travel, make sure that the mains voltage of the country is suitable for this unit.
Keep the original packing material so that you can transport the unit in safe conditions.

This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sufficient magnitude to cause a shock hazard.

This mark attracts the attention of the user to important instructions that are contained in the manual and that he should read and adhere to.

The unit has been certified CE. It is prohibited to make any changes to the unit. They would invalidate the CE certificate and their guarantee!
NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F and 35°C/95°F.

Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your dealer about the way to proceed. The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice.

Do not attempt to make any repairs yourself. This would invalid your warranty. Do not make any changes to the unit. This would also invalid your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use or disrespect of the warnings contained in this manual. Audizio cannot be held responsible for personal injuries caused by a disrespect of the safety recommendations and warnings. This is also applicable to all damages in whatever form.

UNPACKING INSTRUCTION

CAUTION! Carefully unpack the box upon receipt. Check the contents to ensure that all parts are present and have been received in good condition. Notify the shipper immediately and retain packaging material if any parts appear damaged from shipping or the package itself shows signs of mishandling. Save the package and all packaging materials. If the product must be returned, it is important that the product is returned in the original factory box and packaging.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately.
The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.

POWER SUPPLY

On the label on the backside of the product is indicated on this type of power supply must be connected. Check that the mains voltage corresponds to this, all other voltages than specified, the device can be irreparably damaged. The product must also be directly connected to the mains and may be used. No dimmer or adjustable power supply.

Always connect the device to a protected circuit (circuit breaker or fuse). Make sure the device has an appropriate electrical ground to avoid the risk of electrocution or fire.

CONTROLS AND CONNECTION

Volume control
Rotate to adjust the volume level
Power
On/standby
Scan
Press to scan for stations automatically
Menu
Press in DAB- and FM mode to show software version
Info
Press to show channel information
Alarm
Press to set an alarm
Mode
Press to change modes
Press and hold to initiate factory reset function
Preset
Press and hold to save a channel as preset
Press to recall saved presets
Quick preset 1,2 & 3
Press to quickly recall preset 1, preset 2 or preset 3
Tune/Select
Rotate to tune
Press to select
LCD display
Speaker
Antenna
DC 5V IN
Aux in jack 3.5 mm
Battery compartment (4x size “C”)

GETTING STARTED

Remove the radio from the package box.
Plug in the power adapter or insert the correct batteries and press [Power].

Caution: Use only the adaptor supplied with the radio. Connecting a power supply with a different rating can cause permanent damage to the radio and may be hazardous.
When powering the radio by batteries, make sure to disconnect the power adapter from the mains. Close the battery compartment correctly before use. Check the batteries regularly. Remove the batteries from the compartment when not in use to avoid possible leakage.

DAB +

If there is Digital Audio Broadcasting (DAB) in your area, the Radio can pick up the DAB stations as well (no internet connection is required). The radio supports both DAB and DAB+.
Place the radio close to the window and extend the antenna as far as it can go to get the best reception. Sometimes you may need to adjust the direction of the antenna to improve reception.
Press [Mode] to select DAB mode.

Auto select: Press [Scan], “AUTOTUNE FULL SCAN” will appear on the display. The number of found stations will show in the top right corner of the display. The radio will start to play the first found station automatically after completing the scan.
Rotate the [Tune/Select] knob to select another DAB station. Press [Tune/Select] to confirm.
Manual select: Press and hold the [Tune/Select] knob until “MANUAL TUNE” appears on the display. Turn the [Tune/Select] knob to choose a station. Press [Tune/Select] to confirm.

Station presetting: While playing in DAB mode, press and hold [Preset]. “Preset Empty X” will appear on the display. Turn the [Tune/Select] knob to select the desired preset slot (1-10), press [Tune/Select] to store.
Press [Preset] to recall memory. Turn the [Tune/Select] knob to select the stored station you want to listen to. Press [Tune/Select] to confirm. If stations are saved in slot 1, 2 and/or 3, it’s possible to quickly recall them by pressing [1], [2] or [3].

Show channel information: Press [Info] to show various forms of information regarding the station that is being played. Press [Menu] to show the current software version.

FM RADIO

To receive the ordinary FM stations (no internet connection is required), place the radio close to the window and extend the antenna as far as it can go to get the best reception. You may need to adjust the direction of the antenna to improve reception.

Press [Mode] to select FM mode. Press [Scan], the radio will start searching for channels. When a channel has been found, it will be played automatically. If reception is not as desired, use the [Tune/Select] knob to manually fine tune frequency.

Station presetting: While playing in FM mode, press and hold [Preset]. “Preset Empty X” will appear on the display. Turn the [Tune/Select] knob to select the desired preset slot (1-10), press [Tune/Select] to store.
Press [Preset] to recall memory. Turn the [Tune/Select] knob to select the stored station you want to listen to. Press [Tune/Select] to confirm. If stations are saved in slot 1, 2 and/or 3, it’s possible to quickly recall them by pressing [1], [2] or [3].

Show channel information: Press [Info] to show various forms of information regarding the station that is being played.
Press [Menu] to show the current software version.

BT PLAYBACK

Before transmission between your BT device and the radio is possible, both devices must be coupled. This process is called “pairing”. The radio is served as a receiver, to receive the music stream to be played on the radio.
If you have already coupled to a BT device before, this connection will be restored automatically when both devices are in range and BT operation has been selected on the radio. “Pairing” does not have to be repeated. This function may need to be activated in your BT device, however.

Press [Mode] until “BT” shows on the display.
Turn on BT streaming on your device. The device will scan for pairable BT devices in the reception range.
Select “Audizio Corno” from the list with found devices.
Start playback on your BT device. Playback now takes place emitting sound from the radio.

AUX IN

You can listen to the music stored in other audio device or smart phone via the radio, through the connection to the 3.5 mm aux-in jack on the rear side. Use a cable with 3.5 mm pins at both ends, one end connected to the aux-in jack on the radio, the other end connected to the earphone jack on the audio device (or line out socket if available).
Press [Mode] until “AUX IN” shows on the display. Play music on the connected device, the sound will be emitted from the radio.

ALARM SETTING

Alarms will only sound when the unit is “ON” (mains or battery power) or in “STANDBY” (mains power only).
Alarms can be switched on or off in standby mode, however, the alarm parameters can only be set when the unit is turned on.

To set or change alarm 1, press [Alarm] once, then select “ON” and press [Tune/Select]. To set or change alarm 2, press [Alarm] twice, then select “ON” and press [Tune/Select]. To exit the alarm setting mode, press [Alarm] again.

The alarm setup prompts you for the following parameters. Select a value for each parameter by turning the [Tune/Select] knob and press [Tune/Select] to confirm and prompt the next parameter.

Hours
Minutes
Daily, Weekdays, Weekends, Once Choose the days on which the alarm is active.
Source – Beeper 1, Beeper 2, DAB or FM

Press [Alarm] or [Power] when the alarm is sounding to shut it off. The alarm will reset for the next day. The alarm will automatically shut off after 59 minutes when no input is registered.

TECHNICAL SPECIFICATION

Playback options : BT 5.0 streaming, DAB+ tuner, FM radio
Input connections : 3.5mm Jack
Output power : 60W
Power supply : 100-240VAC 50/60Hz (5V Adapter)
Dimensions (L x W x H) : 175 x 310 x 172mm
Weight : 1,70kg

The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice.
The products referred to in this manual conform to the European Community Directives to which they are subject:

European Union

Tronios B.V., Bedrijvenpark Twente Noord 18, 7602KR Almelo, The Netherlands

2014/35/EU
2014/30/EU
2011/65/EC
2014/53/EU

United Kingdom