ENFORCER SK-B111-PQ Indoor Bluetooth Single-Gang Keypad Proximity Reader Instructions

June 9, 2024
ENFORCER

SK-B111-PQ Indoor Bluetooth Single-Gang Keypad Proximity
Reader **
InstructionsENFORCER SK B111 PQ Indoor Bluetooth Single Gang
Keypad Proximity Reader Indoor Bluetooth® Single-Gang
Keypad / Proximity Reader SK-B111-PQ
Additional Information**

SK-B111-PQ Indoor Bluetooth Single-Gang Keypad Proximity Reader

What’s in the Box

1x SK-B111-PQ ENFORCER Indoor Bluetooth® Keypad / Proximity Reader
2x Security screws 11x Crimp connectors 1x Diode 1x Varactor 1x Security screw bit 1x 11-Wire Wiring Harness 1x Quick Installation/Setup Guide 1x Additional Information

Specifications

Operating voltage 9-25 VDC
Current draw Standby
Active (max.) 58mA@12VDC, 33mA@24VDC
Outputs Form C
Tamper alarm 100mA@30VDC (Solid state N.C.)
Egress input N.O. Ground
Door sensor input N.C. Ground
Proximity reader EM 125kHz
Faceplate material Stainless steel, ABS/PC plastic
Operating humidity 0-95%, non-condensing
Operating temperature -4°’-122° F (-20°’-50° C)
Dimensions 23/4″x41/2″x11/4″ (70x114x31 mm)
Weight 3.75-oz (107q)

Sample Wiring Diagram

ENFORCER SK B111 PQ Indoor Bluetooth Single Gang Keypad Proximity Reader -
Sample Wiring

IMPORTANT NOTES

*To protect the relay, you must install the enclosed diode—with the cathode (striped end ) toward the positive side—for DC powered locks and install the  varactor (MOV, ) for AC powered locks and for electromagnetic locks unless your lock has a diode/varactor (MOV) built in. Failure to use these as directed will void the warranty.
† Use the blue wire for fail-secure applications and the yellow wire for fail- safe applications. Use electrical tape to insulate the end of any unused wire.

ENFORCER Bluetooth® Indoor Single-Gang Keypad with Reader

Overview and Installation

ENFORCER SK B111 PQ Indoor Bluetooth Single Gang Keypad Proximity Reader -
Sample Wiring1The reset jumper is only used to reset the device to factory default (see Installation Manual). ENFORCER SK B111 PQ Indoor Bluetooth
Single Gang Keypad Proximity Reader - Sample Wiring2

  1. Connect Wiring
    Feed wires into non-metal back box and connect to wiring harness using the included crimp connectors.

  2. Plug Wiring Harness In
    Plug the wiring harness into the terminal block on the keypad, noting the orientation of the tabs.

  3. Mount Keypad to Back Box
    Using the provided security screws, install the keypad into the back box, taking care not to crimp wires or loosen any connections.

IMPORTANT: Do not install into any type of metal back box as this will affect Bluetooth reception.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by SECO-LARM is under license. Other trademarks and trade names are those of their respective owners.

FCC/IC COMPLIANCE STATEMENT FOR BLUETOOTH MODULE
FCC ID: K7TRB8762
IC ID: 2377ARB8762
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
IMPORTANT WARNING : Incorrect mounting which leads to exposure to rain or moisture inside the enclosure could cause a dangerous electric shock, damage the device, and void the warranty. Users and installers are responsible for ensuring that this product is properly installed and protected from moisture.
IMPORTANT: Users and installers of this product are responsible for ensuring that the installation and configuration of this product complies with all national, state, and local laws and codes. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.
California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information, go to www.P65Warnings.ca.gov.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners.
Copyright © 2022 SECO LARM U.S.A.,
Inc. All rights reserved.

SECO-LARM® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Phone: 949-261-2999 | 800-662-0800
Website: www.seco-larm.com
Email: sales@seco-larm.com
MA_SK-B111-PQ_220615.docx

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ENFORCER User Manuals

Related Manuals