PHILIPS BPP616 Stela Long User Guide

PHILIPS BPP616 Stela Long

in the box 

System Power depends on amount of LEDs: see product label.
Ambient: -20 to+ 35°( in general. Specific max ambient temperature see product label. If nothing stated on the product label max ambient temperature 25°C. Other ambient temperature on request.
Exception for certain versions equipped with dimming gear, mini photocell: please check the gear label.

• This luminaire must be installed only by qualified personnel
• Disconnect before servicing

how to set

Starsense LLC Mounting

TYPES OF MAIN CONNECTOR

Safety instructions

For skilled electricians and trained personnel in accordance with national legislation, including the relevant standards. Observe the national safety rules and regulations for prevention of accidents and the following safety instructions.

1. The technical data on product label indicated on the light fitting and the gear are to be observed.
2. Changes of the design and modification to the light fitting are not permitted.
3. The light fitting shall be operated as intended and in undamaged and perfect condition.
4. Only genuine spare parts may be used for replacement.
5. Repairs may only be carried out by a qualified “electrician”.
6. Do not keep these operating instructions inside the light fitting during operation.

Conformity with standards

• This light fitting meets the requirements of EN 60 598.
• It has been designed, manufactured and tested as a state of art product and according to EN ISO 9001-2000 quality management system.
• It meets CE requirements.

Technical data

Technical details are stated on the product label. This label states number of LEDs, system wattage, supply voltage and frequency, power factor /cos phi, maximal current, electrical insulation class ( if class 2, double insulated), maximum ambient temperature ( if nothing is stated the maximum ambient temperature is 25 degrees C ), IP value , CE mark.

Installation

Observe the respective national regulations as well as the general rules of engineering which apply to the installation and operation of elec­trical apparatus.
Transport and storage of the luminaire is permitted in original packaging and specified position only. Installation instructions are included in the packaging of each luminaire and are to be strictly followed.
We advise to disconnect the lantern from the power supply before gear exchange.

Taking into operation
Prior to operation, check the light fitting for its proper functioning and installation in compliance with these operation instructions, the instal­lation instructions and other applicable regulations.

Maintenance, servicing, and repair

When servicing, in particular those components that affect the type of protection, will have to be checked and replaced if applicable, e.g. Disconnect the lantern from the power supply before opening it or carrying out repairs!
Observe the national regulations applicable to the maintenance, servicing and testing of electrical apparatus as well as the general rules of engineering.

• Depending on environmental circumstances the luminaire may need to be cleaned. For cleaning only use a damp cloth or sponge. Only use customary household wash-up liquid diluted in water. After cleaning rinse with clear water.
• In case of a driver failure, 100% LEDs out, the luminaire can be opened for replacement of this driver.
• Check the gaskets of the driver housing for their perfect condition. Grease the gasket with acid-free grease.
• Check terminal blocks for their firm fit.
• Only use genuine Indal spare parts.
• The LEDs and lenses can not be replaced on site. The IP66 LED/lens compartment may not be opened in order to safeguard the proper light technical, electrical and mechanical working of the luminaire.

Installation instructions

Installation instructions are included in the packaging of each luminaire and are to be strictly followed.

Have you already downloaded the Philips Service tag app?
It helps you make LED maintenance easier and faster!

Download the app

App herunterladen Descargar la app

Place tag on the fuse box
Stelle den Tag auf den Sicherungskasten Colocar la etiqueta en la caja de fusibles Placer le tag sur le boîtier appareillage

Register the product

• Produktregistrierung
• Registrar el producto
• Enregistrer le produit

And also…
Und ebenso… Y también… Et aussi…

• Mounting instructions
  Montageanleitung Instrucciones de montaje Instructions de montage

• Troubleshooting
  Problembehebung Resolución de problemas Dépannage

• Spare parts list
  Ersatzteilliste
  Listado de repuestos
  Liste des pièces de rechange

• Driver re-programming
  Treiber Neuprogrammierung Reprogramación del driver Reprogrammation du Driver

Want to know more about the Service tags?Go to www.philips.com/servicetag

Annex I: Simplified EU Declaration of Conformity
Hereby, Signify Holding declares that the radio equipment type included into the luminary is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.philips.com/lighting

SR compatibility – For SR-based luminaires only SR-Certified components/sensors are to be used (see also: http://www.lighting.philips.co.uk/oem­ emea/products/drivinq-connected- lightinq). The functional compatibility of two (SR-certified) components/sensors to be used in combination, as well as the override possibility of any line-switch function used in an SR-based luminaire, is to be released by the master component/sensor supplier. If using a NEMA 7-pin socket on an SR-based luminaire, a full system verification is required. Not following this advice can/will cause risk of damage and non-compliance for which Signify cannot take any responsibility.

References

• Products | Philips lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>