ARREGUI 41200 Resist Fireproof safe Instructions

ARREGUI 41200 Resist Fireproof safe Instructions

Thank you for purchasing this RESIST safe. We advise you to read the instructions before you install and use the safe to prevent its improper use from making the guarantee void.

  1. CHARACTERISTICS OF THE PRODUCT

This safe is meant to protect your objects of value and your documents in the event of a possible fire. Due to its heavy weight, it is advisable to place it on firm flooring.

FRONT DIAGRAM OF THE SAFE:

  2. OPENING AND CLOSING THE SAFE

   2.1.BATTERIES INSTALLATION AND OPENING

• Extract the battery compartment located outside the safe, at the lower part of the keyboard, and place 4 alkaline batteries of 5 V.
• Press the * A beep sounds and a green LED flashes.
• Enter opening code ( initial master-code is 1-2-3-4- 5-6)
• Every key pressing is confirmed with a beep sound and a green led If the key is not pressed over the course of 10 sec. the lock will switch off and the operation must be repeated.
• Press ENTER
• While the green led is flashing, turn the key clockwise and open the
• If the typed code is incorrect 2 beeps sounds and a red LED flashes during 5 seconds. In this case, start the operation
• The safe allows up to 3 erroneous code entries before it is blocked for 5 minutes as a security During this time, it is not possible to use the keypad. During the blocking period the red LED on the keyboard flashes in 5 seconds intervals.

   3.2. PROGRAMMING USER CODE (using the master-code)

• By default the safe is supplied with user code
• Press the * key + ENTER
• Press the 2 key + ENTER
• Enter the valid master-code (1-2-3-4-5-6 if original one has not been changed in advance) and press ENTER
• Enter the user code (4 digits minimum and 6 digits maximum) and press
• Repeat the user code and press ENTER

   3.3. CHANGING USER CODE (without using master-code)

The change of the user code without using the master code is possible only if the user code was set in advance by using the master code.

• Press the * key + ENTER
• Press the 3 key + ENTER
• Enter the valid user-code and press ENTER
• Enter the new user code (4 digits minimum and 6 digits maximum) and press ENTER
• Repeat the new user code and press

    3.4. DELETING USER CODE (with master-code)

• Press the * key + ENTER
• Press the 0 key + ENTER
• Enter the valid master-code and press ENTER
• The user code is

   2.2. CLOSING

To close the safe, push the door and insert the key and turn it towards left

  3. PROGRAMMING OPENING CODES

This safe has 2 opening codes from 1 to 8 digits each one: a master code and a user code.

   4.CHANGING THE BATTERIES

If the voltage is low, every time “*” key is pressed 5 beeps sounds and the red LED flashes warning the batteries have to be changed.

Extract the battery compartment located outside the safe, at the lower part of the keyboard, and place 4 alkaline batteries of 1.5

1. The code remains saved even if the battery is switched

   5. MAINTENANCE

Check the condition of the battery compartment on a regular basis (every 6 months) to identify any possible signs of rust, sulphation, etc.
Grease/oil any mechanical moving parts, such as locks and bolts.

Read More About This Manual & Download PDF:

References

• Design of mailboxes, safes in Gipuzkoa - Arregui - Orio
• Diseño De Buzones, Cajas Fuertes en Gipuzkoa - Arregui - Orio Gipuzkoa
• Conception de boîtes aux lettres, coffres-forts à Gipuzkoa - Arregui - Orio
• Mailbox Design, casseforti in Gipuzkoa - Arregui - Orio Gipuzkoa
• Diseño De Buzones, Cajas Fuertes en Gipuzkoa - Arregui - Orio Gipuzkoa

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>