HARDIN MARINE 137-8414 Trim Sender Instruction Manual

HARDIN MARINE 137-8414 Trim Sender

TRIM SENDER – GEN 2

DASH PANEL TO SENDER WIRE COLOR CODE

1. BLACK – GROUND
2. RED – 12V/ 5AMP FUSED KEYED POWER
3. YELLOW – DASH LIGHTS
4. BLUE – PORT SENDER BLACK & YELLOW (GROUND)
5. WHITE – PORT SENDER WHITE (SEND)
6. GREY – PORT SENDER RED (POWER)
7. BLUE – STBD SENDER BLACK & YELLOW (GROUND)
8. WHITE – STBD SENDER WHITE (SEND)
9. GREY – STBD SENDER RED (POWER)

OPTIONAL 137-8684 HARNESS KIT COMES WITH:

1. (2) 30′ SENDER HARNESS (GREY, BLUE AND WHITE)
2. (1) 30′ RED WIRE
3. (1) 5AMP FUSE AND HOLDER
4. (20) BUTT CONNECTORS
   USED IN 137-8681, 137-8682, 137-8683, 137-8688 & 137-8737 KITS 06/2022.

ADJUSTING THE LED LIGHT RANGE:

1. MOVE TO DRIVE/TAB ALL THE WAY DOWN.
2. BOTH SENDERS MUST BE WIRED AND THE BOTTOM LIGHT ON BOTH SIDES MUST BE LIT.
3. DEPENDING ON THE KIT, YOU WILL EITHER ADJUST THE END SCREWS OR SLID THE ASSEMBLY TO GET THE BOTTOM LIGHT ON THE DASH TO ILLUMINTE.
4. MOVE THE DRIVE/TAB ALL THE WAY UP.
5. USING 1/16 ALLEN KEY, REMOVE THE BACK COVER.
6. USING A SMALL FLAT SCREWDRIVER, CAREFULLY TURN THE ADJUSTMENT ON THE BACK OFF THE LED PANEL ALL THE WAY COUNTER CLOCKWISE. SOME OF THE TOP LED’S SHOULD TURN OFF.
7. SLOWLY TURN THE ADJUSTING SCREW CLOCKWISE UNTIL THE THE TOP LED LIGHT BEGINS TO ILLUMINATE. PANEL IS NOW ADJUSTED FOR FULL RANGE. NOW ADJUST THE OTHER SIDE. CYCLE UP AND DOWN A FEW TIMES TO MAKE SURE LIGHTS ARE ADJUSTED PROPERLY.
8. REINSTALL REAR COVER.
9. 2 SLOT SHOWN. SAME INSTRUCTIONS FOR 4 AND 6 SLOT PANELS.

WARNING:: ATTACHING POWER TO ANY OTHER WIRE THAN THE RED OR GREY WIRE WILL PERMENANTLY DAMAGE THE SENDER AND DASH PANEL.

THIS DRAWING IS CONFIDENTIAL AND IS SUPPLIED ON EXPRESS CONDITION THAT IT SHALL NOT BE LENT, COPIED OR DISCLOSED TO ANY OTHER PERSON OR USED FOR ANY OTHER PURPOSE WITHOUT WRITTEN CONSENT OF HARDIN MARINE INC.. BREACH OF THIS CONTRACT WILL HOLD …….. AND IT’S PRINCIPALS LIABLE FOR LOSS AND DAMAGES.

137-8414 GENERATION 1 VERSUS 2 COMPARISON

WARNING: ATTACHING POWER TO ANY OTHER WIRE THAN THE RED OR GREY WIRE WILL PERMENANTLY DAMAGE THE SENDER AND DASH PANEL.

137-8414 GENERATION 1 VERSUS 2 COMPARISON

GEN 1 PANEL WIRING:
BLACK: GROUND
RED: 12 V/ 5AMP FUSED POWER WHITE: SENDER INPUT YELLOW: DASH LIGHTS

GEN 2 TRIM SENDER INSTRUCTIONS:\

1. GEN 1 DASH PANEL ONLY HAD 5 WIRES.
2. GEN 1 MAGNET WAS ONLY .200x.200.
3. GEN 2 SENDERS AND PANELS STARTED 06/2022
4. GEN 2 DASH PANEL HAS 9 WIRES.
5. EN 2 SENDER HAS 4 WIRES.
6. DO NOT USE YELLOW WITH GEN 1 PANEL AND MAGNET.
7. FOR GEN 2 PANEL AND MAGNET. COMBINE BOTH BLACK & YELLOW SENDER WIRES TO THE BLUE PANEL GROUND.

GEN 2 PANEL WIRING:

• BLACK: PANEL GROUND
• RED: 12 V/ 5AMP FUSED POWER YELLOW: DASH LIGHTS
• BLUE: SENDER GROUND WHITE: SENDER INPUT
• GREY: 5 VOLT POWER
• BLUE: SENDER GROUND WHITE: SENDER INPUT
• GREY: 5 VOLT POWER

THIS DRAWING IS CONFIDENTIAL AND IS SUPPLIED ON EXPRESS CONDITION THAT IT SHALL NOT BE LENT, COPIED OR DISCLOSED TO ANY OTHER PERSON OR USED FOR ANY OTHER PURPOSE WITHOUT WRITTEN CONSENT OF HARDIN MARINE INC.. BREACH OF THIS CONTRACT WILL HOLD …….. AND IT’S PRINCIPALS LIABLE FOR LOSS AND DAMAGES.

3 WIRE SENDER WIRING

DASH PANEL TO 3 WIRE SENDER WIRE COLOR CODE

1. BLACK – GROUND
2. RED – 12V/ 5AMP FUSED KEYED POWER
3. YELLOW – DASH LIGHTS
4. BLUE – PORT SENDER BLUE WIRE
5. WHITE – PORT SENDER WHITE WIRE
6. GREY – PORT SENDER RED WIRE
7. BLUE – STBD SENDER BLUE WIRE
8. WHITE – STBD SENDER WHITE WIRE
9. GREY – STBD SENDER RED WIRE

WARNING:
ATTACHING POWER TO ANY OTHER WIRE THAN THE RED OR GREY WIRE WILL PERMENANTLY DAMAGE THE SENDER AND DASH PANEL. USED IN 137-8144, 137-8687, 137-8689, 137-8690 & 137-8729 ACTUATOR KITS

ADJUSTING THE LED LIGHT RANGE FOR MERCURY SMARTCRAFT/3 WIRE SENDER:

1. MOVE THE DRIVE/TAB ALL THE WAY DOWN.
2. BOTH SENDERS MUST BE WIRED AND THE BOTTOM LIGHT ON BOTH SIDES MUST BE LIT. IF ONLY ONE SENDER IS BEING USED, WIRE BOTH SIDES OF THE DASH PANEL TO THE SINGLE SENDER.
3. ADJUST THE MERCURY SENDER SO THE BOTTOM LIGHT IS ON. WHEN TIGHTENING THE BOLTS, THE LIGHT MIGHT TURN OFF OR SHOW TWO LIGHTS. IF SO, LOOSEN BOLTS, ADJUST SENDER AND
4. TIGHTEN BOLTS AGAIN. SENDER IS VERY SENSITIVE TO MOVEMENT.
5. MOVE THE DRIVE/TAB ALL THE WAY UP.
6. USING 1/16 ALLEN KEY, REMOVE THE BACK COVER.
7. USING A SMALL FLAT SCREWDRIVER, CAREFULLY TURN THE ADJUSTMENT SCREW ON THE BACK OFF THE LED PANEL ALL THE WAY COUNTERCLOCKWISE. SOME OF THE TOP LED’S SHOULD TURN OFF.
8. SLOWLY TURN THE ADJUSTING SCREW CLOCKWISE UNTIL THE THE TOP LED LIGHT BEGINS TO ILLUMINATE. PANEL IS NOW ADJUSTED FOR FULL RANGE. NOW ADJUST THE OTHER SIDE. CYCLE UP AND DOWN A FEW TIMES TO MAKE SURE LIGHTS ARE ADJUSTED PROPERLY.
9. REINSTALL REAR COVER.
10. 2 SLOT SHOWN. SAME INSTRUCTIONS FOR 4 AND 6 SLOT PANELS.

THIS DRAWING IS CONFIDENTIAL AND IS SUPPLIED ON EXPRESS CONDITION THAT IT SHALL NOT BE LENT, COPIED OR DISCLOSED TO ANY OTHER PERSON OR USED FOR ANY OTHER PURPOSE WITHOUT WRITTEN CONSENT OF HARDIN MARINE INC.. BREACH OF THIS CONTRACT WILL HOLD …….. AND IT’S PRINCIPALS LIABLE FOR LOSS AND DAMAGES.

**HARDIN/MERCURY TRIM TAB WIRING

**

DASH PANEL TO 3 WIRE SENDER WIRE COLOR CODE

1. BLACK – GROUND
2. RED – 12V/ 5AMP FUSED KEYED POWER
3. YELLOW – DASH LIGHTS
4. BLUE – PORT SENDER BLUE WIRE
5. WHITE – PORT SENDER WHITE WIRE
6. GREY – PORT SENDER RED WIRE
7. BLUE – STBD SENDER BLUE WIRE
8. WHITE – STBD SENDER WHITE WIRE
9. GREY – STBD SENDER RED WIRE

ADJUSTING THE LED LIGHT RANGE

1. TRIM TABS COME FROM FACTORY ADJUSTED SO THE BOTTOM OF THE SENDER SHOULD BE ON.
2. BOTH SENDERS MUST BE WIRED AND THE BOTTOM LIGHT ON BOTH SIDES MUST BE LIT.
3. MOVE THE DRIVE/TAB ALL THE WAY UP.
4. USING 1/16 ALLEN KEY, REMOVE THE BACK COVER ON THE DASH PANEL.
5. USING A SMALL FLAT BLADE SCREWDRIVER, CAREFULLY TURN THE ADJUSTMENT ON THE BACK OF THE LED PANEL ALL THE WAY COUNTERCLOCKWISE. SOME OF THE TOP LED’S SHOULD TURN OFF.
6. SLOWLY TURN THE ADJUSTING SCREW CLOCKWISE UNTIL THE THE TOP LED LIGHT BEGINS TO ILLUMINATE. PANEL IS ADJUSTED FOR FULL RANGE. NOW ADJUST THE OTHER SIDE. CYCLE UP AND DOWN A FEW TIMES TO MAKE SURE LIGHTS ARE ADJUSTED PROPERLY.
7. REINSTALL REAR COVER.
8. 2 SLOT SHOWN. SAME INSTRUCTIONS FOR 4 AND 6 SLOT PANELS.

THIS DRAWING IS CONFIDENTIAL AND IS SUPPLIED ON EXPRESS CONDITION THAT IT SHALL NOT BE LENT, COPIED OR DISCLOSED TO ANY OTHER PERSON OR USED FOR ANY OTHER PURPOSE WITHOUT WRITTEN CONSENT OF HARDIN MARINE INC.. BREACH OF THIS CONTRACT WILL HOLD …….. AND IT’S PRINCIPALS LIABLE FOR LOSS AND DAMAGES.

References

• Hardin Marine Performance Products - Performance Marine Parts and More!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>