HARDIN MARINE FL 32137 11 Industry Dr. Palm Coast Instructions
- June 9, 2024
- HARDIN MARINE
Table of Contents
HARDIN MARINE FL 32137 11 Industry Dr. Palm Coast
#6 3 WIRE CONVERSION
ITEM NO.| PART NUMBER| DESCRIPTION| QTY.|
---|---|---|---|---
1| 525-57008| RETAINER| 2|
2| 525-842812| DRIVE, DRIVESHAFT| 1|
3| 525-842814| PIN, #6 HINGE| 1|
4| 525-8M0065246| DRIVESHAFT, SENSOR| 1|
5| 525-8M0095310| SENDER, TRIM 3 WIRE| 1|
6| 90010F075SHS| BOLT, 10-32 x .75| 2|
7| 90010SL-STSS| WASHER, #10| 2|
- 137-8690 DOES NOT INCLUDE #3 PIN HINGE.
- SEE 137-8684 FOR WIRING AND SENDER ADJUSTMENT.
- SENDER ROUTING CAN BE THRU THE MERCURY GIMBAL HOUSING OR BY USING OPTIONAL 137-8652 HOSE AND 135-1060 THRU HULL.
THIS DRAWING IS CONFIDENTIAL AND IS SUPPLIED ON EXPRESS CONDITION THAT IT SHALL NOT BE LENT, COPIED OR DISCLOSED TO ANY OTHER PERSON OR USED FOR ANY OTHER PURPOSE WITHOUT WRITTEN CONSENT OF HARDIN MARINE INC.. BREACH OF THIS CONTRACT WILL HOLD …….. AND IT’S PRINCIPALS LIABLE FOR LOSS AND DAMAGES.
3-WIRE SENDER WIRING
DASH PANEL TO 3 WIRE SENDER WIRE COLOR CODE:
- BLACK – GROUND
- RED – 12V/ 5AMP FUSED KEYED POWER
- YELLOW – DASH LIGHTS
- BLUE – PORT SENDER BLUE WIRE
- WHITE – PORT SENDER WHITE WIRE
- GREY – PORT SENDER RED WIRE
- BLUE – STBD SENDER BLUE WIRE
- WHITE – STBD SENDER WHITE WIRE
- GREY – STBD SENDER RED WIRE
WARNING: ATTACHING POWER TO ANY OTHER WIRE THAN THE RED OR GREY WIRE WILL PERMENANTLY DAMAGE THE SENDER AND DASH PANEL.
USED IN 137-8144, 137-8687, 137-8689, 137-8690 & 137-8729 ACTUATOR KITS
ADJUSTING THE LED LIGHT RANGE FOR MERCURY SMARTCRAFT/3 WIRE SENDER:
- MOVE THE DRIVE/TAB ALL THE WAY DOWN.
- BOTH SENDERS MUST BE WIRED AND THE BOTTOM LIGHT ON BOTH SIDES MUST BE LIT. IF ONLY ONE SENDER IS BEING USED, WIRE BOTH SIDES OF THE DASH PANEL TO THE SINGLE SENDER.
- ADJUST THE MERCURY SENDER SO THE BOTTOM LIGHT IS ON. WHEN TIGHTENING THE BOLTS, THE LIGHT MIGHT TURN OFF OR SHOW TWO LIGHTS. IF SO, LOOSEN BOLTS, ADJUST SENDER AND TIGHTEN BOLTS AGAIN. SENDER IS VERY SENSITIVE TO MOVEMENT.
- MOVE THE DRIVE/TAB ALL THE WAY UP.
- USING 1/16 ALLEN KEY, REMOVE THE BACK COVER.
- USING A SMALL FLAT SCREWDRIVER, CAREFULLY TURN THE ADJUSTMENT SCREW ON THE BACK OFF THE LED PANEL ALL THE WAY COUNTERCLOCKWISE. SOME OF THE TOP LED’S SHOULD TURN OFF.
- SLOWLY TURN THE ADJUSTING SCREW CLOCKWISE UNTIL THE THE TOP LED LIGHT BEGINS TO ILLUMINATE. PANEL IS NOW ADJUSTED FOR FULL RANGE. NOW ADJUST THE OTHER SIDE. CYCLE UP AND DOWN A FEW TIMES TO MAKE SURE LIGHTS ARE ADJUSTED PROPERLY.
- REINSTALL REAR COVER.
- 2 SLOT SHOWN. SAME INSTRUCTIONS FOR 4 AND 6 SLOT PANELS.
MAYFAIR/MERCURY GEN 1 TRIM TAB LED RETRO KIT-PARTS BREAKDOWN
ITEM NO.| PART NUMBER| DESCRIPTION| QTY.|
---|---|---|---|---
1| 137-8057| PIN, TRIM RAM w/ ACTUATOR| 4|
2| 137-8686| SENDER MOUNT| 2|
3| 90010F200SES| SCREW, SET| 2|
4| 90010FP-FNSS| NUT, 10-32| 2|
5| 137-8059| CABLE END, TRIM TAB| 2|
6| 137-8417| FITTING, TRIM TAB SENSOR| 2|
7| 137-8666| HOSE, LED SENDER| 2|
8| 137-8665| SPACER, ACTUATOR PIN| 4|
9| 90010AN-STPL| WASHER, 10 NYLON| 4|
10| 90010AN-STSS| WASHER, #10 AN| 8|
11| 90010CN-FNSS| NUT, 10-24| 4|
12| 90043CN-FNSS| NUT, 7/16-14| 8|
IMPORTANT NOTES:
- ONLY 1 ASSEMBLY SHOWN. KIT COMES WITH 2 OF THESE ASSEMBLIES.
- ALWAYS USE ANTI-SIEZE ON ALL BOLTS & #7 137-8666 HOSE.
- TORQUE #10 NUTS TO 20 IN. LBS..
- TORQUE 7/16 NUTS TO 40 FT. LBS..
- USE LIQUID PIPE TAPE TO INSTALL #6 137- 8417 FITTING.
INSTALLATION INSTRUCTIONS
- REMOVE OLD TRIM PINS AND CABLE THRU HULL FITTINGS.
- SEE PARTS BREAKDOWN PRINT FOR PART NUMBERS AND ASSEMBLY LOCATIONS.
- APPLY ANTI SIEZE TO THE OD OF BOTH 137-8057 PINS AND THREADS. SEE FIG. A.
- SLIDE PINS INTO TABS AND RAMS. MAKE SURE TO KEEP THE ORIGINAL SPACERS IN THE SAME POSITION.
- INSTALL 7/16 NUTS, FIG. B. TORGUE TO 40 FT. LBS..
- SLIDE #10 NYLON WASHER ON THE UPPER STUD, FIG. C.
- SLIDE 137-8665 SPACER ON TO THE LOWER STUD, FIG. D.
- SLIDE SENDER MOUNT ON TO THE STUDS, FIG. E.
- INSTALL #10 NYLON WASHER, #10 STAINESS WASHER AND NUT ON TO THE UPPER STUDS, FIG. F. TORQUE TO 20 IN. LBS..
- INSTALL 137-8665 SPACER, #10 STAINESS WASHER AND NUT ON TO THE LOWER STUD, FIG. G. TORQUE TO 20 IN. LBS.. THE NUTS WILL BOTTOM OUT ON THE STUD. SLIDE SENDER SHOULD BE FREE TO MOVE.
- APPLY LIQUID PIPE TAPE TO 137-8417 FITTING, FIG H. INSTALL IN THREADED HOLE WERE THE CABLE THRU HULL WAS.
- SLIDE WIRES FROM HOSE AND SENDER THRU THE FITTING.
- APPLY ANTI SIEZE TO 137-8417 FITTING AND LED SENDER. INSTALL 137-8666 HOSE, FIG J.
- PROCEDED TO WIRING INSTRUCTIONS.
TRIM SENDER – GEN 2
DASH PANEL TO SENDER WIRE COLOR CODE:
- BLACK – GROUND
- RED – 12V/ 5AMP FUSED KEYED POWER
- YELLOW – DASH LIGHTS
- BLUE – PORT SENDER BLACK & YELLOW (GROUND)
- WHITE – PORT SENDER WHITE (SEND)
- GREY – PORT SENDER RED (POWER)
- BLUE – STBD SENDER BLACK & YELLOW (GROUND)
- WHITE – STBD SENDER WHITE (SEND)
- GREY – STBD SENDER RED (POWER)
OPTIONAL 137-8684 HARNESS KIT COMES WITH:
- (2) 30′ SENDER HARNESS (GREY, BLUE AND WHITE)
- (1) 30′ RED WIRE
- (1) 5AMP FUSE AND HOLDER
- (20) BUTT CONNECTORS
USED IN 137-8681, 137-8682, 137-8683, 137-8688 & 137-8737 KITS 06/2022.
ADJUSTING THE LED LIGHT RANGE:
- MOVE TO DRIVE/TAB ALL THE WAY DOWN.
- BOTH SENDERS MUST BE WIRED AND THE BOTTOM LIGHT ON BOTH SIDES MUST BE LIT.
- DEPENDING ON THE KIT, YOU WILL EITHER ADJUST THE END SCREWS OR SLID THE ASSEMBLY TO GET THE BOTTOM LIGHT ON THE DASH TO ILLUMINTE.
- MOVE THE DRIVE/TAB ALL THE WAY UP.
- USING 1/16 ALLEN KEY, REMOVE THE BACK COVER.
- USING A SMALL FLAT SCREWDRIVER, CAREFULLY TURN THE ADJUSTMENT ON THE BACK OFF THE LED PANEL ALL THE WAY COUNTER CLOCKWISE. SOME OF THE TOP LED’S SHOULD TURN OFF.
- SLOWLY TURN THE ADJUSTING SCREW CLOCKWISE UNTIL THE THE TOP LED LIGHT BEGINS TO ILLUMINATE. PANEL IS NOW ADJUSTED FOR FULL RANGE. NOW ADJUST THE OTHER SIDE. CYCLE UP AND DOWN A FEW TIMES TO MAKE SURE LIGHTS ARE ADJUSTED PROPERLY.
- REINSTALL REAR COVER.
- 2 SLOT SHOWN. SAME INSTRUCTIONS FOR 4 AND 6 SLOT PANELS.
WARNING: ATTACHING POWER TO ANY OTHER WIRE THAN THE RED OR GREY WIRE WILL PERMANENTLY DAMAGE THE SENDER AND DASH PANEL.
References
- Hardin Marine Performance Products - Performance Marine Parts and More!
- Mayfair Performance Marine | Manufacturers of High Performance Marine Accessories
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>