tp-link T315 Tapo Smart Temperature and Humidity Monitor User Guide

: June 9, 2024
: tp-link

Table of Contents

Appearance
**** Before You Start
RF Exposure Information
Documents / Resources

Quick Start Guide
Smart Temperature and
Humidity Monitor

*Images may differ from actual products.
7106509797 REV1.0.0

Appearance

tp-link T315 Tapo Smart Temperature and Humidity Monitor - fig
1

*You can press the button to switch display position.

Indicator Icons

Connection

Blinking: Connecting to hub
Solid On: Connected to hub
Off: No connection

Battery Level
Battery level < 20%
Battery level < 5%
Inside Comfort Level
Outside Comfort Level

Display/Reset Button

Single Press
Switch the temperature unit℃/℉.
Double Press
Switch the display position of temperature and humidity.
Press and hold for 5s
Reset your monitor to enter pairing mode.

**** Before You Start

A Tapo Hub is required. Make sure your Tapo Hub is successfully added via the Tapo app.

https://www.tapo.com/app/download-app/

1. Power Up Your Monitor
Remove the back panel and insert the batteries. The Connection icon should start to blink.
Note: If the Connection icon is not blinking, press and hold the button for 5 seconds to reset your monitor.

2. Set Up Your Monitor
Open the Tapo app and tap the + button. Select Sensors and then your model.
Follow the app instructions to complete setup.

3. Test Your Monitor
Take the monitor to your preferred location.
Make sure the Connection icon on the screen is solid on. If there is no connection icon, move it closer to your hub.

tp-link T315 Tapo Smart Temperature and Humidity Monitor - fig
2

4. Place Your Monitor (The installation height should not be higher than 2 meters.)

Option 1:
Place it on a table or a shelf| Option 2:
Magnetically attach to metallic surfaces| Option 3:
Stick to a clean wall with the included adhesive
---|---|---
tp-link T315 Tapo Smart Temperature and Humidity Monitor - fig
3

For technical support, the user guide and more information, please visit https://www.tapo.com/support/

Warning
Risk of explosion if the battery is replaced by an incorrect type.
Warning
Avoid replacement of a battery with an incorrect type that can defeat a safeguard.
Avoid disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
Do not leave a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; Do not leave a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

Operating Temperature: 0℃(32℉) – 50℃(122℉)
Please keep it away from harsh environments with high temperatures or high humidity.
Do not immerse the vent hole into any liquid.
This monitor is designed to facilitate a healthy lifestyle, but should not be used as a measuring tool.

Do not ingest battery, Chemical Burn Hazard Safety Information
Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use the device where wireless devices are not allowed.
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU,
2009/125/EC, 2011/65/EU and (EU) 2015/863.
The original EU declaration of conformity may be found at https://www.tapo.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK declaration of conformity may be found at https://www.tapo.com/support/ukca/For EU/UK Region:
Operating Frequency / Nominal Operating Frequency / Max Output Power: 863~865MHz / 863.35MHz / 25mW (e.r.p) 863~865MHz / 864.35MHz / 25mW (e.r.p)
868~868.6MHz / 868.35MHz / 25mW (e.r.p)

RF Exposure Information

This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
The device complies with RF specifications when the device used at 20 cm from your body.
Reveiver categories：1

FCC compliance information statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1）This device may not cause harmful interference.
2）This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

NCC Notice

Documents / Resources

| tp- link T315 Tapo Smart Temperature and Humidity Monitor [pdf] User Guide
T315 Tapo Smart Temperature and Humidity Monitor, T315, Tapo Smart Temperature and Humidity Monitor, Smart Temperature and Humidity Monitor, Temperature and Humidity Monitor, Temperature Monitor, Humidity Monitor
---|---
| tp- link T315 Tapo Smart Temperature and Humidity Monitor [pdf] User Guide
T315 Tapo Smart Temperature and Humidity Monitor, T315, Tapo Smart Temperature and Humidity Monitor, Smart Temperature and Humidity Monitor, Temperature and Humidity Monitor, Humidity Monitor, Monitor
| tp- link T315 Tapo Smart Temperature and Humidity Monitor [pdf] User Guide
T315 Tapo Smart Temperature and Humidity Monitor, T315, Tapo Smart Temperature and Humidity Monitor, Temperature and Humidity Monitor, Humidity Monitor, Monitor