LeapFrog LF920HD 7 Inch High Definition Pan & Tilt Monitor User Guide

: June 9, 2024
: LeapFrog

Table of Contents

Important Safety Instructions
What’s Included
Connect, Charge, and Power On the Baby Monitor
Overview
Baby Unit
Parent Unit Icons
General product care
Disposal of batteries and product
Customer service and product warranty
Customer Service
Technical Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**LeapFrog LF920HD 7 Inch High Definition Pan & Tilt Monitor User Guide

**

Important Safety Instructions

The applied nameplate is located at the bottom of the Baby Unit’s base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

Follow all warnings and instructions marked on the product.
Adult setup is required.
CAUTION: Do not install the Baby Unit at a height above 2 meters.
This product is not a substitute for adult supervision of the infant. Supervising the infant is the parent’s or caregiver’s responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby.
Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.
CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the Parent Unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery into fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the information in The RBRC seal.
Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.
Power adapter information: Baby Unit output: Output: 5V DC 1.5A; VTech Telecommunications Ltd.; Model: VT07EAU05150 Parent Unit output: Output: 5V DC 2A; VTech Telecommunications Ltd.; Model: VT07EAU05200
Rechargeable battery information: Zhuhai Great Power Energy Co., Ltd.; Lithium battery, 3.7V 5000mAh; Model: GSP806090-5Ah-3.7V-1S1P
The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, underthe-table or cabinet outlet.
For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.
Unplug this product from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation.
Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped.
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company.
Do not overload wall outlets or use an extension cord.
Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register.
Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.
To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.
You should test the sound reception every time you turn on the units or move one of the components.
Periodically examine all components for damage.
There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time. 22. Children should be supervised to ensure that they do not play with the product.
The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

Use and store the product at a temperature between 32oF and 104oF.
Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.
Batteries should not be exposed to excessive heat such as bright sunshine or fire.
Warning—Strangulation Hazard—Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9m) away). Do not remove this tag.
Never place the Baby Unit(s) inside the baby’s crib or playpen. Never cover the Baby Unit(s) or Parent Unit with anything such as a towel or a blanket.
Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

Should keep wireless devices at least six inches from the pacemaker.
Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.

Electromagnetic fields (EMF)
This Leap Frog product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today

What’s Included

Connect, Charge, and Power On the Baby Monitor

Connect the Baby Monitor

Connect

Charge the Parent Unit Battery

Notes:

Before using the baby monitor for the first time, charge the Parent Unit battery for 12 hours. When the Parent Unit battery is fully charged, the battery icon becomes solid .
The standby time varies depending on your actual usage time and the age of the battery.

Power On or Off the Baby Monitor

Slide the On/Off switch to ON to power on your Baby Unit.
Press and hold until the welcome screen appears.

Status Check

Once your Baby Unit and Parent Unit are powered on and connected, your Parent Unit displays video from the Baby Unit, and the LINK LED light turns on.

Note: Each Parent Unit can pair up to 2 Baby Units.

Positioning the Baby Monitor

Tip: Want to mount Baby Unit on the wall?
Visit our Online Manual to find the wall mounting tutorial video and step- by-step guide.

Note:
To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, cell phones and computers.
Caution:
The default volume of your Parent Unit is level 3, and the maximum volume is level 5. If you experience a screeching noise from your baby monitor while positioning:

Make sure your Baby Unit and Parent Unit are more than 3 feet (1 meter) apart, OR
Lower the volume of your Parent Unit.

Overview

Parent Unit

Link LED light
Battery LED light
3-level sound indicator light
Night Mode quick set key
- Select black-and-white or color night vision viewing mode.
- Adjust night light brightness.
Arrow Keys
Menu / Select
Talk / Return
Volume
- View the volume adjustment bar.
Zoom
Power / LCD Off
Microphone
Antenna
Power jack
RESET
Stand

Baby Unit

Light sensor
Camera
Infrared LEDs
Microphone
Night light
Night light control key
- Press to turn the night light on or off.
- Press and hold to adjust night light brightness level.
Speaker
POWER LED Light
On / Off switch
Temperature sensor
- Position horizontally for optimal usage.
Power jack
Wall mount holes
PAIR / Reset key
- The Parent Unit and Baby Unit (s) provided are already paired.

Parent Unit Icons

Main Menu Icons
Monitoring mode (For LF920HD-2 only)

View Baby Units in Single mode.
View Baby Units in Patrol mode.
View Baby Units in Split screen.

Night light

Turn on/off night light.
Select a night light color.
Adjust brightness.
Set a Timer to turn the night light off.

Lullaby

Play/Stop lullaby.
Select to play all melodies, or play one of the 5 melodies and 5 soothing sounds.
Set a Timer to stop the lullaby.
Set the lullaby volume.

Detection – Sound, motion, temperature

Select the sound and motion sensitivity level.
Turn on/off sound and motion detection alerts.
Turn on/off Auto Wake-up feature.
Turn on/off Temperature Alert.
Select the minimum and maximum Temperature range.
Temperature display format.

Parent Unit settings

Parent Unit screen brightness.
Dim mode

Baby Unit settings

LED Status
Baby Unit’s speaker volume.

General settings

Low Battery Alert tone
No Link Alert Tone

Status icon

Status icon Current view status

Parent unit, baby unit 1 and baby unit 2 (*For LF920HD-2 Only) viewing and connection status.

Baby unit 1 and 2 are being viewed in Patrol mode (*For LF920HD-2 only).

Baby unit 1 and 2 are being viewed in Split mode (*For LF920HD-2 only).

B/W night vision is turned on.

Color night vision is turned on.

Motion detection alert is turned on.

Melodies and soothing sounds are playing.

Night light is turned on.

Auto night light brightness is activated.

Parent unit is muted.
Temperature alert is turned on.
Humidity
Temperature
Battery indicator

General product care

To keep this product working well and looking good, follow these guidelines:

Avoid placing it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps).
DO NOT expose it to direct sunlight or moisture.
Avoid dropping the product or treating it roughly.
Clean with a soft damp cloth.
DO NOT immerse the Parent unit and the Baby Unit in water and do not clean them under running water.
DO NOT use cleaning spray or liquid cleaners.
Make sure the Parent unit and the Baby Unit are dry before you connect them to the mains again.
Clean the USB charging port of dust, dirt, and lint regularly.

Disposal of batteries and product

The crossed-out wheelie bin symbols on products and batteries, or on their respective packaging, indicates they must not be disposed of in domestic waste as they contain substances that can be damaging to the environment and human health.

The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains more than the specified value of mercury (Hg), cadmium (Cd) or lead (Pn) set out in Battery Directive (2006/66/EC). The solid bar indicates that the product was placed on the market after 13th August, 2005. Help protect the environment by disposing of your product or batteries responsibly

Customer service and product warranty

IMPORTANT
Please retain this booklet with your sales receipt as proof of the date of purchase.

Customer Service

If you require assistance in operating this product, please call the TecHelp Information Line on
1300 369 193 or contact VTech by e-mail at: tcpsupport_au@vtech.com

Voluntary Product Enquiry
In addition to your Statutory Rights and subject to the conditions below, VTech warrants that this product will be free from any defect in
materials or workmanship under conditions of normal use for a period of 24 months from date of purchase.

VTech does not warrant that the product will be free from defects if defects are caused by an accident, misuse, abuse, improper installation
or operation, vermin infestations, lack of reasonable care, unauthorised modification, loss of parts, tampering or attempted repair by a person
not authorised by VTech; or where the product has been damaged by lightning or a mains power surge.To make a claim under this Voluntary
Product Warranty you must call the TecHelp Information Line on 1300 369 193 or contact VTech by e-mail at: tcpsupport_au@vtech.com where a Customer Service Representative will inform you of the product return process. You will need to ensure that:

You provide proof of purchase;
Your product is suitably packaged (original packaging is not required); and
You have included all components from the original purchase.

For your records
Date of purchase:
Place of purchase:
Serial number:

For Voluntary Product Warranty purposes, proof of purchase is required so please keep your receipt.

The benefits conferred by this Voluntary Product Warranty are in addition to other rights and remedies that are available to you under law, which cannot be excluded. The processes for this Voluntary Product Warranty in no way limit your rights which arise as a result of your Statutory Rights.

This Voluntary Product Warranty is given by: VTech Telecommunications (Australia) Pty Ltd ABN 70 136 672 627 Address: 24 Gilby Road, Mount Waverley 3149

IMPORTANT NOTE: THIS IS NOT A PRODUCT RETURN OR SERVICE ADDRESS – PLEASE CONTACT TECHELP BY PHONE OR EMAIL FOR PRODUCT AND WARRANTY SUPPORT. NO LIABILITY WILL BE ACCEPTED BY VTECH FOR PRODUCTS RETURNED TO THIS ADDRESS UNDER THIS VOLUNTARY PRODUCT WARRANTY.

Phone number: 1300 369 193
Email address: tcpsupport_au@vtech.com

Statutory Rights
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund
for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or

replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Find the answer to your question on our knowledge-rich Online Manual. Get assisted at your own pace and learn what your monitor is capable of.

Scan the QR code to access the Online Manual or visit leapfrog.com.au/support

Full Manual
Comprehensive help articles on product set up, operations, Wi-Fi and settings.

Video Tutorials
Walk-throughs on features and installation such as mounting the Baby Unit on the wall.

FAQs & Troubleshooting
Answers to the most commonly asked questions, including troubleshooting solutions.

Technical Specifications

Frequency control: Crystal controlled PLL synthesizer

Transmit frequency: Baby Unit: 2.405-2.475GHz Parent Unit: 2.405-2.475GHz

Channels: 32

LCD: 7” Color LCD (IPS 1280×800 pixels)

Nominal: Actual operating range may vary according to environmental
effective range: conditions at the time of use.

Power requirements: Parent Unit: 3.7V 5000mAh Lithium-ion battery Baby Unit power adapter: Output: 5V DC @ 1.5A Parent Unit power adapter: Output: 5V DC @ 2A

Credits:
The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. nThe Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license. The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license.