WATTS BT-WR02 RF Wireless Wall Receiver User Guide
- June 9, 2024
- WATTS
Table of Contents
WATTS BT-WR02 RF Wireless Wall Receiver User Guide
Presentation
- The BT-WR02 RF receiver is a Wall mounting receiver, designed to control heating regulation system with a wireless thermostat BT-XX02 or BT XX03 .
- This couple (Thermostat Receiver) can also be managed by a Central to have full control of your heating installation from one point.
A ( RF configuration button )| B (Green/Red)| C (red)|
D (green)|
---|---|---|---|---
/| green| /| /| Power ON
Short press| green| /| /| Instantaneous RF transmission
3sec press| green| /| Green flash| Thermostat or Central RF init.
15sec press| Red blinking| /| Greenblinking| Reset of the receiver
/| green| red| /| Heating demand
/| green| /| Green flash| RF reception
/| Red| /| /| Pilot wire information
/| green| /| Permanently Greenblinking| RF Alarm
Technical characteristics
Environment. (Temperatures) Operating : shipping et storage :| **
0°C – 40°C-10°C to +50°C
---|---
Power supply| 230Vac 50Hz
Electrical protection| Class II – IP33
Pilot wire Input (French market)| 6 orders Pilot Wire by phase (L)
Output Maximum Load| Relay 10Amps 250VACUp to 10A – 250Vac 50Hz (2
wires L,N)
Radio Frequency & RF Receiving distance| 868MHz < 10mW (Bidirectional
communication) Range of approximately 100m in open space.Range of
approximately 30m in residential environment.
CE Directives Your product has been designed in conformity with the
European Directives.| Low voltage (LVD) – Directive
2014/35/EUElectromagnetic compatibility (EMC) – Directive
2014/30/EURestriction of the use of certain hazardous substances (RoHS) –
Directive 2011/65/EU Ecodesign and Energy Labelling – Directive 2009/125/EC
and Regulation (EU) 2017/1369 Radio equipment – Directive 2014/53/EU
Product conformed to : Classification : Contribution :**| UE 811/2013
and 2010/30/UE IV(2%)
Installation and RF Initialisation rules
Install and connect the receiver respecting the following guidelines to guarantee an optimal reception:
- The receiver must be mounted at a minimum distance of 50cm of all others electrical or wireless materials like GSM, Wi-Fi router.
- Wiring work related to the receiver must be carried out only when de energized
- Connect your receiver to the power supply.
Depending on your installation, an order of pairing must be respected to
ensure a correct RF signal transmission.
Installation 1: Receiver + RF thermostat
- Switch on the receiver.
- Press the RF button during 3 sec to switch to RF Init.
- The RF LED should be Green fixed or orange blink indicating that the Receiver is now in radio configuration mode waiting for a thermostat configuration address.
- Please refer to the thermostat leaflet for enter the thermostat in “RF Init” mode.
- The receiver RF LED must be switched OFF and the thermostat should exit the RF init mode to indicate correct paring between both elements.
You can pair several receivers to the same RF thermostats
Note for installations 2 and 3: You can pair several receivers. Pay attention! Before linking a new receiver with the Central unit, you have to reset the receiver imperatively.
Installation 2: Receiver + RF Thermostat + RF Central unit for heating regulation
- First step is to pair the RF thermostat to the Central unit
- Press the RF button on the receiver during 3sec.
- The RF LED should be Green fixed or orange blink indicating that the Receiver is now in radio configuration mode waiting for a central configuration address.
- Please refer to the leaflet of the Central unit for more explanation about the pairing mode “RF Init”. You must pair the Receiver as a heating device in the Central unit
- The RF LED on the receiver will switch OFF and the Central will show a message to indicate correct pairing between both elements.
You can pair several receivers in the same room.
Installation 3: Receiver + RF Central unit for ON/OFF or light control
- Press the RF Button 3sec to switch the Receiver in RF Init mode .
- The RF LED should be Green fixed or orange blink indicating that the Receiver is now in radio configuration mode waiting for a central configuration address.
- Please refer to the leaflet of the Central unit for more explanation about the pairing mode “RF Init”. You must pair the Receiver as an ON/OFF plug or a light in the Central unit
- The RF LED on the receiver will switch OFF and the Central will show a message to indicate correct pairing between both elements.
You can pair several receivers in the same room. Receiver will work in Timer mode; you have the possibility to create a weekly program for ON/OFF period.
Remarks:
- In case of a thermostat in RF Alarm, the receiver (BT-FR02 RF or BT WR02 RF) will follow 20% cycle of heating to prevent the installation against frost. (The receiver will stay in OFF mode if it was in OFF before the loss of RF communication).
- Plug receiver, Flush receiver, Wall receiver: The leds are switched off between 8pm and 8am when using a BT-DP02 RF
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>