ACiQ Remote Controller Owner’s Manual
- June 9, 2024
- ACiQ
Table of Contents
ACiQ Remote Controller
INTRODUCTION
Thank you for purchasing our air conditioner. Please read this manual carefully before operating your new air conditioning unit. Make sure to save this manual for future reference
Remote Controller Specifications
Quick Start Guide
Handling the Remote Controller
Inserting and Replacing Batteries
- Slide the back cover from the remote control downward, exposing the battery compartment.
- Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
- Slide the battery cover back into place
BATTERY NOTES
- For optimum product performance:
- Do not mix old and new batteries, or batteries of different types.
- Do not leave batteries in the remote control if you don’t plan on using the device for more than 2 months.
BATTERY DISPOSAL
Do not dispose of batteries as unsorted municipal waste. Refer to local laws
for proper disposal of batteries.
TIPS FOR USING REMOTE CONTROL
- The remote control must be used within 8 meters of the unit.
- The unit will beep when remote signal is received.
- Curtains, other materials and direct sunlight can interfere with the infrared signal receiver.
- Remove batteries if the remote will not be used more than 2 months
Buttons and Functions
Before you begin using your new air conditioner, make sure to familiarize
yourself with its remote control. The following is a brief introduction to the
remote control itself. For instructions on how to operate your air
conditioner, refer to the How to Use Basic Functions section of this
manual.
Remote Screen Indicators
Information are displayed when the remote controller is power up
How to Use Basic Functions
AUTO Mode
COOL or HEAT Mode
DRY Mode
FAN Mode
Setting the TIMER
TIMER ON/OFF – Set the amount of time after which the unit will automatically turn on/off.
TIMER ON setting
TIMER OFF setting
TIMER ON & OFF setting(example)
How to Use Advanced Functions
Swing function
Airflow direction
If continue to press the SWING button, five different airflow directions
can be set. The louver can be move at a certain range each time you press the
button. Press the button until the direction you prefer is reached(some u nits
only).
LED DISPLAY
- Press this button to turn on and turn off the display on the indoor unit.
- Keep pressing this button more than 5 seconds, the indoor unit will display the actual room temperature. Press more than 5 seconds again will revert back to display the setting temperature
ECO/GEAR function
Press this button to enter the energy efficient mode in a sequence of following: ECO GEAR(75%) GEAR(50%) Previous setting mode ECO…...
ECO operation
Under cooling mode, press this button, the remote controller will adjust the temperature automatically to 24 C/75 F, fan speed of Auto to save energy (only when the set temperature is less than 24 C/75 F). If the set temperature is above 24 C/75 F, press the ECO button, the fan speed will change to Auto, the set temperature will remain unchanged
GEAR operation
- Press the ECO/GEAR button to enter the GEAR operation as following:
- 75%(up to 75% electrial energy consumption)
- 50%(up to 50% electrial energy consumption)
- Previous setting mode
ECO Intelligent Eye Function(For models of RG10L series)
Press this button Under ECO Intelligent eye mode, with the built-in infrared sensor, the unit can detect the people’s activities in the room. In Cooling mode ,when you are away for 30 minutes, the unit automatically lowers the frequency to save energy (for inverter models only). And the unit will automatically resume operation if sensing human activity again.
Silence function Keep pressing Fan button for more than 2 seconds to activate/disable Silence function(some units). Due to low frequency operation of compressor, it may result in insufficient cooling and heating capacity. Press ON/OFF, Mode, Sleep, Turbo or Clean button while operating will cancel silence function.
FP function Press this button 2 times during one second under HEAT Mode and setting temperature of 16 C/60 F or 20 C/68 F(for models RG10L10(G2HS)/BGEF & RG10L10(D2HS)/BGEF only).
FCC
The device could comply with the local national regulations.
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>