MERCUSYS MB110-4G LTE Router User Guide

: June 9, 2024
: MERCUSYS

Table of Contents

MERCUSYS MB110-4G LTE Router
Hardware Connection
- Connect the Hardware
FAQ (Frequently Asked Questions)
Safety Information
EU Declaration of Conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MERCUSYS MB110-4G LTE Router

http://www.mercusys.com

Hardware Connection

MERCUSYS-MB110-4G-LTE-Router-01 *Image may differ from actual product.

Connect the Hardware

Insert the SIM card into the slot until you hear a click.
Connect the power adapter to the router.
Wait until the LED turns on. Your router is connected to the internet successfully.
Note: If the LED does not turn on (no internet), refer to FAQ-2.
Enjoy the Internet
Connect your device to the router (wired or wireless).
The default wireless network name (SSID) and password are printed on the label at the bottom of the router.

Customize the Router

Make sure your computer is connected to the router (wired or wireless).
Launch a web browser and type in http://mwlogin.net. Create a password for future logins.
Follow the Quick Setup instructions to complete the initial configuration.
Note: The router can also be used (or configured) in Wireless
Router Mode for DSL/Cable connections. For more information, please refer to the user guide at https://www.mercusys.com/support/.

FAQ (Frequently Asked Questions)

What should I do if I cannot access the web management page?
- Reboot your router and try again.
- If the computer is set to a static IP address, change its settings to obtain an IP address automatically.
- Make sure http://mwlogin.net is correctly entered in the web browser.
- Use another web browser and try again.
- Disable and then enable the active network adapter and try again.
What should I do if I cannot access the internet?
- Verify that your SIM card is an LTE or WCDMA card.
- Verify that your SIM card is in your ISP’s service area.
- Verify that your SIM card has sufficient credit.
- Log in to the router’s web management page, and check the following:
1. Go to Advanced > Network > PIN Management to verify if PIN is required. If it is, enter the correct PIN provided by your ISP.
2. Go to Advanced > Network > Internet to verify the parameters provided by your ISP are correctly entered. If they are incorrect, create a profile with the correct parameters, then select the new profile from the Profile Name list.
3. Go to Advanced > Network > Data Settings to verify if the used data exceeds the allowance. If it does, click Correct and set the used data to 0 (zero), or disable Data Limit.
4. Go to Advanced > Network > Internet to verify that Mobile Data is enabled. If it is not, enable it to access the internet.
5. Confirm with your ISP if you are in a roaming service area. If you are, go to Advanced > Network > Internet to enable Data Roaming.
How do I restore the router to its factory default settings?
- With the router powered on, press and hold the WPS/RESET button on the rear panel until the Power LED starts blinking, then release the button.
- Log in to the router’s web management page, and go to Advanced > System Tools > Backup & Restore to reset the router.
What should I do if I forget my wireless network password?
- The default wireless password is printed on the product label of the router.
- Connect a computer directly to the router via an Ethernet cable. Log in to the router’s web management page and go to Basic > Wireless to retrieve or reset your wireless password.

Safety Information

Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Do not use the device where wireless devices are not allowed.
Adapter shall be installed near the equipment and shall be easily accessible.
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.English: Safety Information
Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Do not use the device where wireless devices are not allowed.
Adapter shall be installed near the equipment and shall be easily accessible.
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

EU Declaration of Conformity

MERCUSYS hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at http://www.mercusys.com/en/ce.