HINKLEY 30025-30026 Free-Standing Fridge-Freezer Instruction Manual

HINKLEY 30025-30026 Free-Standing Fridge-Freezer

Assembly Instructions

1. Find a clear area in which you can work.
2. Unpack the fixture and glass from the carton.
3. Carefully review instructions prior to assembly

Shut off the electrical current before starting. If the fixture you are replacing is turned on and off by a wall switch, simply turn the switch off. If not, remove the appropriate fuse (or open the circuit breakers) until the fixture until the new fixture is completely wired and in place.

1. To begin assembly of your fixture first slip stem (1) along wire and thread onto the threaded tube (A) and tighten.
2. Next refer to the instruction sheet (FRIS-19), provided, on how tO hang your fixture from the ceiling.

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN THE POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Make electrical connections from supply wire to fixture lead wires. Refer to the instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to complete the installation of this fixture.

hanging instructions

start here

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

1. Shut off the electrical current before starting. If the fixture you are replacing is turned on and off by a wall switch, simply turn the switch off. If not, remove the appropriate fuse (or open the circuit breakers) until the fixture is dead.

DO NOT restore current – either by fuse, breaker or switch – until the new fixture is completely wired and in place.

1. Fasten mounting strap provided – see (1) to outlet box ( A) with the two 8-32 screws ( 2) not Drawing 1.
2. Thread 2 – hex nuts( 3a) and ( 3b) onto threaded tubing ( 4).
3. Thread one end of threaded tubing ( 4) into a loop ( 5) a minimum of 1/2’’ to 3/4’’. Tighten hex nut ( 3a) against loop ( 5) to lock loop in position.
4. Thread another end of the threaded tube ( 4) into the mounting strap approximately 1/2’’.
5. Slip canopy ( B) over loop ( 5) and adjust the height of the loop so half of the threaded area on the loop is exposed – see Drawing 2 below. After the loop height is adjusted, tighten hex nut (3b) up against the mounting strap, and tighten it against the mounting strap to lock the loop and threaded tube in position.
6. Remove mounting strap ( 1) from junction box ( A), and thread third hex nut ( 3c) onto the end of the threaded tube ( 4) above the mounting strap, tighten against the mounting strap to lock the assembly in position.
7. Remount the mounting strap to the junction box.

Drawing 2

1. Taking the chain, determine the length you require to hang the fixture.
2. Attach one end of the chain to the top loop of the fixture.
3. Now slip loop collar (6) and canopy (B) onto the chain. — – see Drawing 2
4. Attach another end of chain to loop (5). Get assistance for this step since fixture may be heavy and difficult to hold while attaching the chain.

Canopy Adjustment

1. Unwrap fixture lead wire and ground wire and weave them up through the chain.
2. Slip fixture lead wire and ground wire through the center of loop ( 5).
3. Connect ground wire to mounting strap ( 1) using green ground screw ( GS).
4. Make electrical connections from supply wire to fixture lead wires. Refer to the instruction sheet ( I.S. 1 8) and follow all instructions to make all necessary wiring connections.
5. Slip canopy up firmly against the ceiling and secure by turning the threaded collar ( 6) on loop ( 5) until tight.

wiring grounding instructions

SAFE TY WARNI NG: READ WIRIN G AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN THE POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

wiring instructions

Indoor Fixtures

1. Connect positive supply wire (A ) (typically black or the smooth he, GGunma red side of the two-conductor cord) to positive fixture lead (B ) with an appropriately sized twist on the connector – see Drawings 1 or 2.
2. Connect the negative supply wire (C) (typically white or ribbed, marked side of the two-conductor cord) to the negative fixture lead (D).
3. Please refer to the grounding instructions below to complete all electrical connections

Outdoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth unmared side of the two-conductor cord) to the positive fixture lead (B) with an appropriately sized twist on the connector — see Drawings 2 or 3.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Cover open end of connectors with silicone sealant to form a watertight seal. If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box . If the wall surface is lap siding, use caulk and a fixture mounting platform especially.
4. Please refer to the grounding instructions below to complete all electrical connections.

grounding instructions

Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M ) with the ground screw (S) – see Drawing 1.
Note: On straps for screw-supported fixtures, first install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.

Chain Hung Fixtures
Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on the fixture mounting strap (M ) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Draw in g 2.
Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coa ted) to power supply ground with app appropriately sized twist-on connector inside the post. Cover open end of the connector with silicone sealant to form a watertight seal – see Drawing 3.

Roca 8 Lights Pendant – Unpacking Procedure

HINKLEY 33000 Pin Oak Parkway, Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkley.com

References

• ley.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>