sygonix 2472505 Smart Ceiling Fan Instruction Manual

Operating Instructions
Smart Ceiling Fan, 36 W, White
Item No. 2472505

Introduction

Dear customer,
Thank you for purchasing this product.
If there are any technical questions, please contact: www.conrad.com/contact

Intended use

The product is a mains powered ceiling fan with integrated LED light source.The fan blades will automatically retract when the fan stops spinning. The  product can be operated via the TUYA “Smart Life – Smart Living” application and included transmitter (remote control).
The product is intended for indoor use only. Do not use it outdoors. Contact with moisture must be avoided under all circumstances.
If you use the product for purposes other than those described, the product may be damaged. Improper use can result in short circuits, fires, electric shocks or other hazards.
The product complies with the statutory national and European requirements. For safety and approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product available to third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights reserved.

Delivery content

• Hanger bracket
• Receiver
• Canopy
• Canopy cap
• Coupling cover| • Motor housing + light kit
• Acrylic light cover
• 2x downrods: 10 cm & 25 cm
• Installation kit: 4x short screws, 4x washers, 2x expansion screws| • Balancing kit
• R pin & Clevis pin
• Remote controller with wall bracket
• Operating instructions.
---|---|---

Up-to-date operating instructions

Download the latest operating instructions at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.

http://www.conrad.com/downloads

Description of symbols

The following symbols are on the product/appliance or are used in the text:

| The symbol warns of hazards that can lead to personal injury.
---|---
| The symbol warns of dangerous voltage that can lead to personal injury by electric shock.
| The minimum distance between the lamp and any illuminated objects must be greater than 1m.

| For indoor use in dry locations.
| Not dimmable.
| Read the instructions.

Safety instructions

**** Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on  proper handling in this manual, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

7.1 Read first

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of  xperience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.

7.2 General information

• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
• If you have questions which remain unanswered by these operating instructions, contact our technical support service or other technical personnel.
• Maintenance, modifications and repairs must only be completed by a technician or an authorised repair centre.

7.3 Handling

• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.

7.4 Operating environment

• Do not place the product under any mechanical stress.
• Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.
• Protect the product from high humidity and moisture.
• Protect the product from direct sunlight.
• Do not switch the product on after it has been taken from a cold to a warm environment. The condensation that forms might destroy the product. Allow the product to reach room temperature before you use it.

7.5 Operation

• Consult an expert when in doubt about the operation, safety or connection of the appliance.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product:
  – is visibly damaged,
  – is no longer working properly,
  – has been stored for extended periods in poor ambient conditions or
  – has been subjected to any serious transport-related stresses.

7.6 LED light

• Attention, LED light:
  – Do not look directly into the LED light!
  – Do not look into the beam directly or with optical instruments!

7.7 (Rechargeable) batteries

• Correct polarity must be observed while inserting the (rechargeable) battery.
• The (rechargeable) batteries should be removed from the device if it is not used for a long period of time to avoid damage through leaking. Leaking  or damaged (rechargeable) batteries might cause acid burns when in contact with skin, therefore use suitable protective gloves to handle corrupted  (rechargeable) batteries.
• (Rechargeable) batteries must be kept out of reach of children. Do not leave (rechargeable) batteries lying around, as there is risk, that children or pets swallow them.
• All (rechargeable) batteries should be replaced at the same time. Mixing old and new (rechargeable) batteries in the device can lead to (rechargeable) battery leakage and device damage.
• (Rechargeable) batteries must not be dismantled, short-circuited or thrown into fire. Never recharge non-rechargeable batteries.
  There is a risk of explosion!

7.8 Electrical installation

• The means for disconnection from the power supply must be incorporated in the fixed wiring in accordance with the wiring rules.
  WARNING! Safety hazard!
  The product should only be installed by people with relevant electrical knowledge and experience! *)
  If it is not installed properly, you risk:

•  your own life

• the life of user of the electrical device

• severe damage to property, e.g., by fire

• personal liability for personal injury and material damage Always consult an electrician!
  *) Technical knowledge required to perform the installation: For the installation, the following specialist knowledge is required in particular:

• The “Five safety rules”: Disconnect from the mains; protect against accidental switch-on; ensure there is no voltage; earth and short-circuit; cover or protect adjacent live parts

• Use of suitable tools, measuring devices and personal protective equipment, where necessary

• Analysis of measurement results

• Use of electrical installation materials to meet the requirements for disconnection

• IP protection ratings

• Installation of electrical installation materials

• Type of power supply (TN system, IT system, TT system) and the corresponding connection criteria (classic earthing, protective earthing, necessary additional measures etc.)
  If you are not a professional, do not do it yourself, have it performed by a specialist.

7.9 Installation

• The attachment to the ceiling should have sufficient strength to support 4x the weight of the ceiling fan.
• When penetrating the surface e.g. drilling or inserting fasteners, make sure no cables or pipes are damaged.
• Mounting of the suspension system should be performed by the manufacturer, its service agent, or suitably qualified persons.
• The fan should be installed so that the blades are more than 2.3 m above the floor.

Product overview

8.1 Fan

1 Downrod 10 cm
2 Hanger bracket
3 Canopy
4 R pin
5 Housing (motor + light)
6 Remote control receiver
7 Downrod 25 cm| 8 Canopy cap
9 Coupling cover
10 Clevis pin
11 Acrylic light cover
12 2x concrete expansion screws
13 4x washers
14 4x wood screws
15 2x adhesive balance weights
---|---

8.2 Remote controller (transmitter)

Note:
Pressing any button after the 2H (2 hour) timer has been set will clear the timer..

A Indicator light
B FAN OFF: power OFF
C 2H (Short press): timer 2 hrs
2H (Long press): Wi-Fi connect
D Switch: forward / reverse
E LED-: decrease brightness| F Warm white light: ON
G Cool white light: ON
H Natural white light: ON
I “Natural” wind:
fan speed cycle 1 – 6 – 1| J Light ON/OFF: switch light ON/OFF
K Fan speed select: 1 – 6
L LED+: increase brightness
M Battery compartment
N Wall mount
---|---|---

8.3 Receiver

Remote (transmitter) and receiver pairing

The transmistter and receiver were paired at the factory. If the connection is broken, follow these steps:

1. Switch the fan power OFF for 10 seconds.

2. Switch the fan power back ON.
   A beep will sound, within 3 seconds press and hold the FAN OFF b utton on the remote control until you hear a second beep, then release the button.

3. The pairing process is complete. If for some reason the pairing process failed, repeat steps 1 and 2.

Installation

Risk of fatal electric shock! Always switch the mains power supply off before beginning installation.
Mounting of the suspension system should be performed by the manufacturer, its service agent, or suitably qualified persons.

Important:
– Do not overtighten screws as this can strip threads and/or damage the product.
– The fan should be installed so that the blades are more than 2.3 m above the floor.
– Observe the minimum clearances shown. Failure to do so can result in injury and/or damage.
– Observe: “7.8 Electrical installation” on page 26.
– Observe: “7.9 Installation” on page 26.” 10.1 Install the hanger bracket

Tools needed:

10.1.1 Wooden ceiling

Important:
– Make sure the wood type is suitable. Do not install the product to particle board.

• Use 4x wood screws and 4x washers when mounting the hanger backet to the ceiling.
• Use 4x dowels if needed (not included).

10.1.2 Concrete ceiling

Use 2x expansion bolts and washers to mount the hanger backet to the ceiling.

10.1.3 Connect downrod and hanger ball

| | |
---|---|---|---
Release the pin.| Loosen the 2x screws.| Slide down.| Remove the pin.

The product is supplied with the 10 cm downrod attached. Replace it with the 25 cm rod to fit a higher ceiling.

| |
---|---|---
Insert the canopy, canopy cap, and coupling cover, thenpass the cables through the downrod. 2x holes  facing down, 3x holes facing up.| Replace the pin.| Slide the suspension ball
|
Slide the suspension ball| Loosen the screws, attach the downrod frame to the housing, then tighten.

10.2 Hanging the product

Rotate until the slot on the ball fits into the lug of the bracket.
10.3 Connect the receiver

When the wiring is complete, insert the receiver as shown.

10.4 Set the canopy When finished wiring, attach the canopy to the hanger bracket. Push up and twist to locate the screws into the holes, and then firmly tighten.
NOTE: The  screws protrude for attaching the canopy cap.Attach the canopy cap to the canopy.

10.5 Set the plastic shade

• Remove 3x screws and attach the housing.
• Use 3x washers as shown.
• Connect the light kit as shown.
• Position the plastic shade and twist it until it locks into place.
• Make sure it is securely fastened before letting go.

Inserting batteries (remote control)

1. Remove the battery compartment cover.
2. Insert 2x 1.5 V AAA batteries matching the polarities shown inside the compartment.
3. Replace the compartment cover.

Application “Smart Life – Smart Living”

12.1 Download application
Compatible Android™ and iOS apps are available from their respective app stores. Search for the TUYA “Smart Life – Smart Living” application.

12.2 Connection tips

• The product is compatible with 2.4 GHz networks.
• Enter the exact network name (case sensitive).
• Connect the mobile device to the same Wi-Fi network the product will connect to.
• If you are giving the product to a third party you did not “Share Device” with, you may need to “Remove Device” through the application before they can link it to their account.
• Enable Bluetooth on your mobile device.

12.3 Open for pairing (Wi-Fi)
To open the product for pairing with the application:

1. Switch the fan power ON.
2. Press and hold the 2H button on the remote until two or more beeps sound, then release the button.
3. The product is ready to be paired with the application.

12.4 Connection pathway

• Add device > Small Home Appliances > Fan (BLE + Wi-Fi)
• Follow the onscreen instructions to complete the process.

Balancing the fan

Important:
Before performing any work or maintenance, always:
– Switch the fan power OFF.
– Disconnect the power supply and prevent against accidental restart.
– Make sure the fan has stopped spinning.
If the fan wobbles when in use, first check the following:

• All connection screws are sufficiently tightened.
• All fittings are correctly inserted/aligned e.g. hanger bracket.

If the problem persists you may need to adjust the balance as follows:

1. You may need to move the adhesive, so lightly attach it to the flywheel at position 1 .

2. Switch the fan ON and set it to the maximumspeed.
   →If the fan is still wobbling repeat steps 1 and 2, with the adhesive at positions 2 and then3.

3. If the fan stops wobbling, you have found the correct position. Firmly press the adhesive down to apply it permanently.
   → The fan is now balanced.a Adhesive balance weight.
   b Flywheel
   c Blade

Troubleshooting

fuses or circuit breakers.
■ Check wire connections to the fan.
Fan is noisy| ■ Top canopy touching ceiling.
■ Loose fan blade screws.
■ Ceiling fan not secured against ceiling.| ■ Lower the canopy from the ceiling.
■ Check all fan blade screws are sufficiently tightened. Do not to overtighten.
■  Check base/hanger screws are sufficiently tightened. Do not to overtighten.
Mechanical noise| | Allow the fan to run for approx. 8 hrs to allow parts to settle.
Fan wobbles| ■  Check all connection screws are sufficiently tightened.
■  Check all fittings are correctly
inserted/aligned e.g. hanger bracket.| ■  Fasten any loose screws.
■  Balance the fan blades. See section “12 Bal-ancing the fan” on page 35.

Cleaning and care

Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions. They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.

1. Disconnect the product from the power supply.
2. Wait for the fan to come to a complete stop.
3. Clean the product with a dry, fibre-free cloth.

Maintenance

1. Check all fastenings at least twice a year to make sure they are sufficiently tight.
2. Tighten if necessary.

Disposal

17.1 Product
This symbol must appear on any electrical and electronic equipment placed on the EU market. This symbol indicates that this device should not be  disposed of as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separately from unsorted municipal waste. Spent batteries and accumulators, which are not enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-destructive manner, must be  removed by end users from the WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste. Conrad provides the following return options free of charge (more details on our website):

•  in our Conrad offices
•  at the Conrad collection points
• at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG

End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply in countries outside of Germany.

17.2 (Rechargeable) batteries
Remove batteries/rechargeable batteries, if any, and dispose of them separately from the product. According to the Battery Directive, end users are legally obliged to return all spent batteries/rechargeable batteries; they must not be disposed of in the normal household waste.
Batteries/rechargeable batteries containing hazardous substances are labelled with this symbol to indicate that disposal in household waste is forbidden. The abbreviations for heavy metals in batteries are: Cd = Cadmium, Hg = Mercury, Pb = Lead (name on (rechargeable) batteries, e.g. below the trash icon on the left).
Used (rechargeable) batteries can be returned to collection points in your municipality, our stores or wherever (rechargeable) batteries are sold. You thus fulfil your statutory obligations and contribute to environmental protection.
Batteries/rechargeable batteries that are disposed of should be protected against short circuit and their exposed terminals should be covered completely with insulating tape before disposal. Even empty batteries/rechargeable batteries can contain residual energy that may cause them to swell, burst, catch fire or explode in the event of a short circuit.

Declaration of Conformity (DOC)

Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this product conforms to the 2014/53/EU directive.

• Click on the following link to read the full text of the EU declaration of conformity: www.conrad.com/downloads

Enter the product item number in the search box. You can then download the EU declaration of conformity in the available languages.

Technical data

19.1 General
Input voltage / current ……………………….220 – 240 V/AC, 50/60 Hz
Protection class …………………………………..I
Operating/Storage conditions …………. 10 to +70 °C, ≤90 % relative humidity (non- condensing)
Dimensions (ø x H) …………………………..480 x 400 mm (blades retracted)
Weight ………………………………………………….7.5 kg
19.2 Fan
Power consumption ……………………..16 W
Speed ……………………………………………max. 250 rpm
Number of blades ………………………..3
Coverage area …………………………..10 – 15 m²
19.3 LED light
This product contains a light source of energy efficiency class F.
LED …………………………………………………..96 pcs CCT
Power consumption ……………………………36 W
Color temperature/lumen ………………..3000 K (1282 lm), 4000 K (1372 lm), 6000 K (1434 lm)
19.4 Transmitter (remote control)
Power supply ………………………………2x 1.5 V AAA batteries
Frequency …………………………………..433.92 MHz
Transmission power…………………….max. -21.844 dBm
Transmission distance ………………..10 m
19.5 Bluetooth (receiver)
Frequency ……………………………………2402 – 2480 MHz
Transmission power………………………max. 6 dBm
Transmission distance …………………..50 m
19.6 Wi-Fi (receiver)
Frequency …………………………………….2412 – 2472 MHz
Transmission power……………………..max. 16.45 dBm
Transmission distance …………………50 m
19.7 Application
Supported OS ……………………….. iOS 10 or above, Android 5.0 or above
Application name ………………….. TUYA “Smart Life – Smart Living”
19.8 Compliance data (fan)

Conrad-Str. 1, D-92240 Hirschau

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the technical status at the time of printing. Copyright 2022 by Conrad Electronic SE.

References

• France.fr : Explore France and its wonders - Explore France
• Conrad Electronic » Alle Teile des Erfolgs
• Conrad Electronic » All parts of success
• Conrad Electronic – Alle Teile des Erfolgs
• Conrad Electronic » All parts of success
• Contact
• Download center
• Conrad Electronic Online Shop » Alle Teile des Erfolgs
• Conrad Electronic » All parts of success

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>