MELEC ML-MRWPB-120-M Weather Protected Batten Instruction Manual
- June 9, 2024
- MELEC
Table of Contents
MELEC ML-MRWPB-120-M Weather Protected Batten Instruction Manual
Product information
The new MRWPB has been designed to provide a solution where a tough and
durable weatherproof fitting is required in a slim overall package.
These are the perfect option when simple functionality is required.
Rear and side entry options for easy linking and conduit entry.
Combined diffuser and gear tray lead to exceptionally fast fit off.
Vandal resistant latches can be secured to stop any tampering. 3 Colour
selection with a fixed power driver.
Flexible mounting options utilizing the supplied adjustable clips or direct to
surface. IK10 and IP65 ratings for the toughest of conditions.
TECHNICAL INFORMATION
| ML-MRWPB-60-M| ML-MRWPB-120-M
---|---|---
Total Power:| 20W| 40W
MAX Lumen Output:| WW 2013lm
NW 2230lm
W 2035lm| WW 4142lm
NW 4739lm
W 4201lm
Colour Temp:| WW 3000K
NW 4000K
W 6000K
IP Rating:| IP65
Efficacy:| WW 96 lm/w
NW 114 lm/w
W 99 lm/w| WW 103lm/w
NW 124 lm/w
W 106 lm/w
CRI:| 80
Beam Angle:| 120°
Temp Range:| -20° to 40°C
Dimmable:| NO
Power Supply:| LIFUD NON-ISOLATED DRIVER
Average Life:| 50,000 hrs
Inrush current at 240V Current(max):| ≤9A & 3uS @ 230V|
≤45A & 3uS @ 230V
Input current at 240V| 0.1A| 0.19A
Power Factor:| 0.9
Earth leakage current| 5mA
IK Rating| IK10
Dimensions:| 66011085mm| 120011085mm
Weight:| 1.1KG| 1.3KG
Warranty:**| 5 years
Data subject to change, please visit our website for up to date specifications: melec.com.au
Dimensions
Total power consumed including driver
Average life is calculated on expected average lifespan.
INSTALLATION GUIDE
-
Install the surface mounting brackets and screws according to the dimensions of the mounting rails of the fitting.
-
Open the fitting by releasing the clips securing the diffuser and LED gear tray.
-
Terminate according to the wiring diagram.
-
If using a cable gland, turn the sealing nut clockwise to ensure proper ingress protection of cable.
-
Close the fitting by re-installing the clips, ensuring that the diffuser properly mates with the fitting gasket to maintain ingress protection.
-
Install the fitting onto the mounting brackets. Test accordingly.
WIRING DIAGARM
PLEASE NOTE
MUST BE INSTALLED BY A LICENSED ELECTRICIAN
- Read instructions carefully before attempting to install the fitting. Retain this guide for future reference
- Disconnect power before installing or servicing
- This fitting is for outdoor use and should not be used in areas with limited ventilation or high ambient temperatures
- Do not extend low voltage cables from the output of power supply
- All components must not be mechanically stressed
- Be careful not to damage or destroy conductive paths on the circuit board
- Follow all relevant electrical and safety standards (including AS3000)
- Correct electrical polarity must be observed as the wrong polarity may destroy the product and is not covered under warranty
- Damage by corrosion will not be honored as a material defect claim. It is the user’s responsibility to provide suitable protection against corrosive agents such as moisture, condensation and other harmful elements.
Warranty
FREE ONSITE WARRANTY
EXCLUSIVE TO MEMBERS ONLY
FREE ONSITE WARRANTY FOR 3 YEARS INCLUDES PARTS & LABOUR
In conjunction with your standard product warranty.
CUSTOMER SUPPORT
T: 1300 222 445
www.melec.com.au
For further information about our Warranties please go to:
melec.com.au/legal/warranties
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>