ZEEGMA Sap Pro Fruit Pusher User Manual

Sap Pro Fruit Pusher
User Manual

Sap Pro Fruit Pusher

Introduction

Dear customer!
Thank you for placing trust in us and choosing Zeegma.
We provide you with a product perfect for everyday use thanks to the use of high-quality materials and modern solutions.
We are convinced that the product will satisfy your requirements as it has been carefully manufactured.
Before you use the product, please read this operating manual carefully.
Should you have any remarks or questions concerning the product, please do not hesitate to contact us: support@zeegma.com

Important
Please read this operating manual before you start using the device to see its functions and use them in accordance with intended use.

• Keep this operating manual for future reference.

• Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, if they have been given supervision or  instruction concerning use of the appliance in a safe way and if they understand the hazards involved.

• Children must not play with this device.

• Do not use the device for more than 20 minutes. If you do, leave the device for 5 minutes to let it cool down before you reuse it.

• The appliance shall not be used by children. Keep the appliance and its cord out of reach of children.

• Do not try to repair the device on your own (does not apply to suggestions from the chapter: Troubleshooting). If the device acts up, report it to the manufacturer’s  authorized service center.

• Do not clean the motor under running water and do not immerse it in water or other liquids to avoid electric shock.

• If:
  • the device or one of its parts is too hot,
  • power cord smells of burning or abnormally vibrates,
  • the tank or any other accessory is cracked,
  • the device acts up, unplug the product and report it to the authorized service center.

• Do not jerk the power cord of the device and remember to dedust it on a regular basis.

• To unplug the product, pull the plug, never a wire.

• If the device is off, unplug it.

• Do not use the device if the power cord or plug is damaged.

• Do not wrap the power cord around the product.

• Do not store the device and its power cord near fire or sources of heat.

• The power cord plug must be properly inserted into the socket, otherwise fire may start.

• To supply power to the device, do not use power other than 220 – 240 V.

• During operation, do not place such items as teaspoons, sticks, brushes in the tank. Do not put fingers either.

• Do not use the device if it stands on an unstable surface.

• Do not use the device near furniture or walls, the product may make them dirty.

• Always disconnect the appliance from the supply if it is left unattended and before assembling, disassembling or cleaning.

• Do not use the product to squeeze hard fruits or vegetables.

• Do not use the product if there are no fruits or vegetables inside.

• Do not open the product cover when it is operating.

• None of the product elements must be used in the microwave.

• Do not store the product in the sunlight as colors may fade.

• Use elements included in the set only.

• If you wish to move the device – unplug it and take a tank out of it.

• Hard and fiber-rich vegetables and fruits (e.g. celery, carrot) must be sliced (1,5-2cm thick and not more than 2cm long).

• Do not use the appliance if the rotating sieve or the protecting cover is damaged or has visible cracks.

• Household use only.

The product complies with requirements of EU directives.
Pursuant to the Directive 2012/19/EU, this product is subject to selective collection. The product must not be disposed of along with domestic waste as it may pose a threat  to the environment and human health. The worn-out product must be handed over to electrics and electronics recycling center.

Description (fig. 1)

7. Pulp outlet

How to assemble the device

The device must be assembled on a flat and stable surface. The device must not be plugged in when you are assembling it.

1. Place the rubber seal in the pulp outlet (fig. 2).

2. If you have difficulties with placing the seal, you can moisten it with a bit of water.
   NOTE! Before every use, make sure the rubber seal is properly placed.

3. Install separately packed plugs at the end of pulp and juice outlet (fig. 3). See fig. 4:

4. Place the tank on the base and turn in a clockwise direction.

5. Put collecting rubbers on the sieve.

6. Insert the screen into the automatic cleaning module and then place in the tank.
   Rotate it so that arrows marks „▲ ” contact at the tank and screen.

7. Insert the rotating screw inside the screen, gently press and rotate.

8. Place the feeder on the tank, rotate as much as possible in a clockwise direction.
   Arrows marks „ ▲” must contact each other at the tank and screen.

9. Plug in.

Control panel options (fig. 5)
Note: Do not insert many products at a time. Large number of products may cause the charge tube or rotating screw to get blocked, which may eventually block the  device.

– beetroot
– celery root| – Wash all products and cut into long pieces so that they can go through the charge tube easily. Use a pusher to push remaining pieces.
– Press „R” key (11) if the device is blocked when operating.
2| Hard fruits| – apple
– pears| – Wash and cut into pieces so that they easily fit the hole.
3| Soft fruits/vegetables| – tomatoes
– peaches
– watermelon| – Insert or/and cut fruits and vegetables so that they easily fit the hole.
-As for hard-stone fruits, e.g. peach, take the large stone out before putting into the device.
4| Juice| – tomatoes – apples
– beetroot| – Mix soft fruits with some hard fruits or vegetables. Do not slice or dice, etc. Too small or too large pieces hinder juicing.
5| Vegetable juice| – celery
– beetroot| – Use hard vegetables and the ones which are not so fibrous.
– As for celery and other high-fiber vegetables, cut them so that their length is about 2 cm.
– Slowly insert vegetables into the squeezer.
6| Nut/soya milk| – soya
– cashew nut| – Such nuts as soya, cashew nut must be soaked for 8-12 hours.
– Insert nuts soaked with water into the squeezer in order to grate them. Add milk or sugar as per your liking.
7| Sorbet (or salad
available with additional accessory only)| – strawberries – raspberries – berries| – To prepare the sorbet, use a sorbet sieve (without holes) and lock the juice plug
– Activate the device in „sorbet” mode and insert frozen fruits through the outlet
– The ready sorbet will escape through the pulp outlet
8| Squeezer washing| – pure water| – Pour pure water, close juice and pulp outlet plugs; Next activate washing function;
– When it is done, remove plugs and pour the water out.
| On/off key. To select the program in other process, press this key to activate program selection. Press „Menu” key  to select program and confirm with on/off key.
---|---
| Program selection key on panel.
| Start and pause selected program key.
| Motor direction change key. Use it when the device gets blocked.

How to use

How to use the cover (fig. 6)

• Slide the key to the left and the cover will open automatically.
• Press the cover, hold and slide the key to the right, the cover will lock.

How to juice large fruits/vegetables (e.g. apple, pear, tomato) (fig. 7).

• Open the cover of input hole, insert the entire apple, use a pusher to support juicing.

NOTE! Hard and fiber-rich vegetables and fruits (e.g. celery, carrot) must be sliced (1,5-2 cm thick and not more than 2 cm long).
How to juice small fruits or vegetables (fig. 8)

• Open the cover of input hole, insert vegetables/fruits (large pieces of fruits or vegetables, cut to relevant size), use a pusher to support juicing.
  NOTE! Never put your palm inside the tank when the device is operating!

How to disassemble the device (fig. 9)
To disassemble the device, follow the steps described in the assembly instructions in a reversed order.
Tips:

• When juicing leaves (e.g. spinach), the device may emit louder sounds, it is acceptable.

• The quality and looks of the juice are affected by freshness of vegetables and fruits used.

• Some fruits and vegetables may leave more pulp in the juice than others.
  Filter this juice before drinking, if necessary.

• Carrot juice may contain less water and more residues.

• If you insert too many ingredients in the squeezer, the tank may get blocked.

• If you can see the tank is blocked and juice does not come out – remove some ingredients.

• If you use various ingredients to make juice, it is advisable to mix their order.

• If one of juice ingredients is leaves, insert them into the device along with other fruit to maintain squeezing capability.

• Be careful when juicing hard fruits and vegetables (e.g. carrots). The device may overheat earlier.

Troubleshooting

fruits/vegetables. press ,.R” (reverse switch), wait for about 2-3 seconds, if the squeezer does not unblock, repeat the procedure. If the machine still fails to operate, clean the machine.
Haven’t you inserted too many fruits/vegetables?| Follow the steps above.
Has the device been
operating for more than 20 minutes?| Leave the squeezer for about 10 minutes to let it cool down, start again if necessary.
Juice contains pulp or juice comes out of pulp outlet.| Has the rubber seal been properly installed?| Apply or correct the rubber seal as described in the manual.
Motor is too loud or vibrates.| Is the device standing on a flat surface?| Place the squeezer on a flat surface.
Have all pieces of the set been properly assembled?| If the product has been properly assembled, overripe fruits/vegetables may have been used – it is not surprising that the product is louder.
Tank contains pulp and juice takes on a color.| Tanks and accessories may take on colors when you use products with pigment (e.g. carrot, spinach. etc.).| Clean the device shortly after use.

Salad accessories (fig. 11)

Assembly of salad accessories:

1. Place the mandrel to connect motor axle.
2. Put the tank on the base and rotate in a clockwise direction.
3. Insert the knife inside the tank.
4. Place the cover on the tank, rotate as much as possible in a clockwise direction.
5. Connect to power supply.

How to clean and maintain

Cleaning before use:

1. Follow the tips presented in the manual to assemble the entire device.
2. Close the pulp and juice outlets with plugs (see fig. 10). Connect to power supply.
3. Pour 500 ml of water and activate „squeezer washing” function on the panel. The procedure will be completed automatically. Next remove plugs and pour the water out.

Cleaning after use:
Before you start cleaning, unplug the device. The device must be cleaned after every use.

1. How to clean a motor base
   Do not immerse the motor base in water and do not clean under running water. Use a soft and wet cloth. To clean cable and plug, use a soft cloth.

2. How to clean a rotating screw
   Use a brush or wet cloth to clean the remaining pulp. The rotating screw may be cleaned under running water.

3. How to clean other pieces of the set
   Disassembled parts can be washed with pure water. Do not use dishwasher.
   Do not dry pieces with a drier, for example. Remove pulp from the device 5 minutes after you finished squeezing at the latest.
   After cleaning, dry parts and store in a clean place.
   NOTE! Do not use detergents, such as solvent, diluter, bleach or other chlorine- or benzene-rich agents. Do not use abrasive materials and brushes with sharp tips.

The pictures are for reference only. The real design of the products may differ from the pictures presented.

BrandLine Group Service – Support
List of Authorized Service Centers:
www.zeegma.com/en/service
Croatia
Uvoznik: Viva-net d.o.o.
A.T. Mimare 8
10090 Zagreb
Tel: 01/ 56 01 715, Fax: 01/ 56 01 945
Thank you for purchasing our product!
zeegma.com

References

• Service - Shop ZEEGMA.com
• Zeegma - Home completed - Shop ZEEGMA.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>