marta MT-FN2530 Stand Fan User Manual

: June 9, 2024
: MARTA

Table of Contents

Introduction
BEFORE THE FIRST USE
USING THE DEVICE
CLEANING AND MAINTENANCE
SPECIFICATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

marta MT-FN2530 Stand Fan User Manual

Introduction

STAND FAN

GBR Parts list

Front grille
Blade cap
Blades
Rear grille nut
Rear grille
Motor shaft
Oscillating knob
Motor
Vertical adjustment screw
Switch mode buttons
Screw
Extension pole
Out-joint
Stand tube
Stand cover
Base

CAUTION
Read this manual carefully before using the appliance and save it for future reference.

Before the first use, check the device specifications and the power supply in your network.
It is not intended for industrial use. For indoor use only. Use only for domestic purposes according to the
instruction manual. Do not use with damaged cord, plug or other injuries. Keep the power cord away from sharp edges and hot surfaces.
Do not pull the cord. Always take the socket. Do not reel the cord around the device housing. Never attempt to frame and repair the appliance by yourself. If you meet problems, please contact the nearest
customer service center. Using accessories or replacement parts that are not recommended or sold by the manufacturer may cause damage to the appliance.
Always unplug the appliance and let it cool down before cleaning and removing parts. Keep unplugged when not in use. To avoid electric shock and fire, do not immerse in water or other liquids. If this
occurs, immediately unplug it and contact service center for inspection. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Do not touch running parts of the fan. Keep
foreign objects away from running parts and grille. Do not block air inlets on the motor block. Do not use the fan without protective grilles.

BEFORE THE FIRST USE

For packaging reasons the fan was delivered unassembled.
Do not connect the fan to the mains supply before you have completely finished the assembly.
Please take note of the following steps when assembling the fan.
Tighten stand tube to stand base with screw.
Fix base cover to stand base with a screw.
Unscrew out-joint, put the stand cover and base cover on the stand base, pull the extension pole out then tighten the out-joint again.
Place control box firmly on top of extension pole, tighten screw.
Unscrew the blade cap by turning clockwise and rear grill nut by turning counter clockwise and put both blade cap and rear grill nut off the motor shaft.
Put rear grille on motor shaft.
Secure it with rear grille nut.
Slide blades on motor shaft so that claws on motor shaft match the blades slots.
Screw blade cap on shaft by turning counter clockwise.
Put front grille on rear grille and close clips or screw grille ring to secure grilles together.
Adjust the fan vertically by vertical adjustment screw.
The fan is ready for work

USING THE DEVICE

NOTE: Do not use the fan in wet conditions (for example rain) in order to avoid electrical shocks.

Always place the fan on a dry and even surface. To make the fan oscillate, push the oscillation button down; pull the button up to stop the oscillation.

SPEED CONTROL To switch on the fan, simply press any of the speed control buttons:

1 – low airflow speed
2 – medium airflow speed
3 – high airflow speed
0 – off

CLEANING AND MAINTENANCE

Before cleaning, always unplug the appliance.
Do not use chemical and abrasive cleaners for cleaning.
For seasonal storage use carton to cover the fan.
Loosen fittings and remove the front grille.
Use a cloth soaked in soapy water to the fan fans.
Do not immerse the appliance in water

SPECIFICATION

Producer:
Cosmos Far View International Limited Room 701, 16 apt, Lane 165, Rainbow North Street , Ningbo, China Made in China

WARRANTY DOES NOT COVER SUPPLIES (filters, ceramic and non-stick coating, rubber seals, etc.)
Production date is available in the serial number located on the identification sticker on the gift box and/or on sticker on the device.
The serial number consists of 13 characters, the 4th and 5th characters indicate the month, the 6th and 7th indicate the year of device production.
Producer may change the complete set, appearance, country of manufacture, warranty and technical characteristics of the model without notice.
Please check when purchasing device.