tracer 46807 RGB Ring Lamp Instruction Manual

June 9, 2024
Tracer

tracer 46807 RGB Ring Lamp

tracer-46807-RGB-Ring-Lamp-PRODUCT - Copy

Safety Instruction

Please read and retain for future reference the following carefully to ensure the satisfactory and safe operation of the light.

Note:

  • This appliance is intended for domestic use only.
  • Before the first use, remove all packaging elements.
  • Unwind and straighten the power cord before use.
  • Make sure that the power cord and plug have no visible damage.
  • Make sure that the power cord is not stretched over an open flame or other heat source that may damage the cable insulation.
  • The cable must be positioned so as not to present a risk of tripping or entanglement This product is not a toy. Make sure children are supervised and do not play with the product
  • This device is not intended for use by persons (including young children) with reduced physical, sensory or mental abilities or without experience and knowledge, unless they are supervised or instructed in the use of the device by a person responsible for their safety.
  • Do not expose the device to moisture
  • Disconnect the AC adapter when not in usetracer-46807-RGB-Ring-Lamp-FIG-1

Fits most Smartphones, Smartphone NOT INCLUDED. Images for illustration purposes only, colors and contents may vary. Sizes are approximate. The lamp contains non-replaceable LEDs’.

Assembly

  • Unfold all three legs from tripod and place on a level surfacetracer-46807-RGB-Ring-Lamp-FIG-2
  • Screw the pan/tilt adjuster onto the top of the tripodtracer-46807-RGB-Ring-Lamp-FIG-3
  • Screw the ring light onto the base until it is tight
  • Screw the goose neck phone holder onto the ring light
  • Pull the right side of the clip to the size of your phone

RGB RING lamp TRACER 26cm with USB cable control button and a remote control. The lamp contains 153 LEDs, including: 33 LEDs 5050 RGB and 120 LEDs 2835 (60 white LEDs and 60 warm LEDs). The lamp reflects the following light colors: white, warm, neutral and 15 other colors – each color has 10 levels of light intensity adjustment.

Operating the lamp with USB cable control button

tracer-46807-RGB-Ring-
Lamp-FIG-5

Connect the USB conector to a power source. Press the ON / OFF button .
To turn the white, neutral or warm light on press the button . Change colours by pressing the same button .
The „Up” or „Down” buttons are used to change the light intensity.
The „Down” button is used to reduce the intensity, the „Up” button – to increase the light intensity. Each color has 10 levels of regulation.
The „Mode” button is used to activate the color light modes. A total of 17 modes of light. Modes by order:

  1. Colors changing one by one:
  2. Smooth color transitions one into another including all the above colors
  3. RGB – slow smooth color changing
  4. RGB – faster smooth color changing
  5. RGB – the fastest smooth color changing mode
  6. Red – green color
  7. Blue – light blue color
  8. Multicolor mode 1 changing and going round the lampshade
  9. Multicolor mode 2 changing and going round the lampshade
  10. White – red color
  11. White – green color
  12. White – blue color
  13. White – yellow color
  14. White – purple color
  15. White – light blue color
  16. All the colors appearing sequentially, one changing into another
  17. Flashing white light color
    Light intensity in each of the above listed modes can be adjusted by „UP” or „down” button
    Press the button to switch on one of the below listed colorsE. ach press of the button will change color to anoter: red, orange, light orange.y ellow, aquamarine, green, mint, turquoise, blue, dark blue, navy blue, light blue ,purple, pink, dark pink

Note: When you press ON/OFF button it will remember your last setting.

Operating the lamp with remote control
The remote control contains a CR2025 3V lithium battery Recommended battery: CR2025 3V lithium
To replace the battery follow the instructions on the back of the remote control

tracer-46807-RGB-Ring-Lamp-FIG-13

Modes will display in the same order as described above when controlling the lamp with USB cable control button
Press Auto  button to display all the available modes in order one by one
Use the button to change modes.
Use the buttons S+ S- to slow or speed up the modes
Lock button . Works with the following modes: White, Warm, Neutral, Red, Green, Blue. After pressing this button, the lamp will lock the selected mode, unabling to change the color, mode, dim and brighten or turning off. IN ORDER TO UNLOCK THE LAMP PRESS THE LOCK BUTTON AGAIN.

Safe use instruction

  1. Do not cover the lamp with any objects
  2. Do not pull the power cable
  3. Be careful with hot surfaces
  4. Do not stare at the light source
  5. Do not touch with wet hands
  6. Indoor use only
  7. Protect against rain and moisture
  8. Do not throw it
  9. The product is not a toy

Operating the device with a damaged power cord is prohibited The light source of this luminaire is not replaceable; when the light source is worn out, the entire lighting fitting must be replace

Product disposal

  1. Packaging components in the form of paper, cardboard and similar materials should be transferred to waste paper or thrown into waste containers intended for paper
  2. Plastic elements such as polystyrene, films, granular fillers and similar should be thrown into containers intended for plastics
  3. A worn out or permanently damaged lighting fitting may not be disposed with general waste. Due to the presence of hazardous substances, it should be handed over to an appropriate recycling place for electrical and electronic waste.

Parameters

tracer-46807-RGB-Ring-Lamp-FIG-19 tracer-46807
-RGB-Ring-Lamp-FIG-20

This device is marked in accordance with the European Directive 2012/19 / EU and the Polish Act of September 11, 2015 “On waste electrical and electronic equipment” (Journal of Laws October 23, 2015, item 11688) with the symbol of a crossed-out container on waste. Such marking informs that the equipment, after its useful life, cannot be placed together with other household waste. The user is obliged to hand it over to the waste electric and electronic equipment collectors. Collectors, including local collection points, shops and municipal units, create an appropriate system for returning the equipment. Proper handling of used electrical and electronic equipment helps to avoid consequences harmful to human health and the natural environment, resulting from the presence of hazardous components and improper storage and processing of such equipment.

Producent:
Megabajt Sp. z o.o., ul. Rydygiera 8,
01-793 Warszawa

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals