FuseBox TD1 Time Switch 7 Day Single Channel Instruction Manual
- June 9, 2024
- FuseBox
Table of Contents
FuseBox TD1 Time Switch 7 Day Single Channel
Technical information
Rating (A)| 16A/250V AC resistive load
4A/250V AC inductive load
---|---
Voltage(V)| 220-240V 50/60Hz
IP RATING| IP20 EN 60529
Mounting| 35mm top hat din rail
Torque (switch terminals)| 0.8Nm
Maximum cable| 4mm²
Memory locations| 16 ON 16 OFF
Power consumption| 7.5VA
Display| LCD
Minimum setting| 1 minute
Bell function| 30s (set ON and OFF time the same)
Contacts| 1 changeover contact (3,4,5)
Battery| Lithium battery, 150H reserve
Ambient temperature| -10~ +40℃
Ambient humidity| 35~85%RH
Weight| 150g
Accuracy| ≤2sec/day(at25℃)
Complies with| EN 60730
IMPORTANT| VOLTAGE FREE CONTACTS
-
Dimensions
Connections (VOLTAGE FREE CONTACTS) -
Time Switch must be installed by a qualified electrician in accordance with the current IET Wiring Regulations BS 7671.
-
Total load must not exceed the rating of the time switch or any additional limitation.
-
For loads greater than above, we recommend an installation contactor is used, switched by the TD1 Time Switch.
BUTTON FUNCTIONS
| BUTTON | FUNCTION |
|---|---|
| ON LED | Illuminates when switching program is on |
| **** | Program button |
| ¹ | Clock /Time button |
| D+ | Day |
| H+ | Hour |
| M+ | Minute |
| RESET | CAUTION This will DELETE ALL settings! |
| By pressing D+ and H+ for 3sec this will also delete |
all settings!
MANUAL| Manual switch for the following settings:
ON, ON AUTO, OFF, AUTO OFF
Initial setup
-
1. Connect SUPPLY to terminals 1 and 2 and LOAD to terminals 4 and 5. Torque connections to 0.8Nm. Loose connections cause fires!!!! - Press and hold “RESET” button for 3seconds to initiate programing functions.
Setting the DAY and TIME
Default setting is 24H mode if you wish to change to 12H press “¹”button
for 5 sec, and LCD will display
AM. If you want to change back to 24H mode press “¹”button 5 sec
Step| Key| Setting the DAY
1| Press and hold ¹ and press D+ TO
CHANGE DAY| The day is displayed at the top of the LCD display
| | Setting the TIME
2| Press and hold ¹ and press H+ TO
CHANGE HOUR| Setting the hour
3| Press and hold ¹ and press M+ TO
CHANGE MINUTE| Setting the minutes
4| Press ¹| To return to display
Before you start programming the time clock select the function required:
PROGRAMMING, PULSE OR COUNTDOWN (Only 1 of the 3 options can be used
simultaneously).
Programming
| Step | Key | Programming ON memory locations |
|---|---|---|
| 1 | Press | Setting 1 ON time (display 1 ON) |
| 2 | Press H+ or M+ | Set hours and minutes |
| 3 | Press D+ | DEFAULT IS EVERY DAY OF |
THE WEEK or you can select one of the following options by pressing
the D+ button
OPTIONS: MO-FR,MO-SA,SA SU,MO-WE,TH-SA,MO WE FR,TU TH SA
Step| Key| Programming OFF memory locations
4| Press| Setting 1 OFF time (display 1 OFF)
5| Press H+ or M+| Set hours and minutes
6| Press D+| DEFAULT IS EVERY DAY OF
THE WEEK or you can select one of the following options by pressing
the D+ button
OPTIONS: MO-FR,MO-SA,SA SU,MO-WE,TH-SA,MO WE FR,TU TH SA
7| Repeat step 2-6| Set 2-16 ON/OFF times
8| Press ¹| End
To review programmed time settings press
FOR THE PROGRAMMED TIMES TO OPERATE AUTOMATICALLY THE TIMER MUST BE SET TO
“AUTO OFF”
(ON LED is NOT ILLUMINATED)
IF YOU ARE WITHIN THE SWITCHING TIMES YOU SHOULD SET THE TIMER TO “AUTO ON”
(ON LED is ILLUMINATED)
MANUAL OVERRIDE Press “MANUAL” to turn ON, ON AUTO, OFF, AUTO OFF programmed
times
Pulse (“P” displayed at left hand side of LCD)
| Step | Key | Programming ON memory location |
|---|---|---|
| 1 | Press and HOLD H+ and M+ | Enter pulse |
setting (“P” will display LHS)
2| Press ¹ and H+ or M+| Set pulse time range: 1sec
to 59min 59sec
3| Press ¹ and MANUAL| To confirm pulse time range (“P”
flashes)
4| Press P| Into setting 1 ON time
(display 1 ON)
5| Press H+/M+| Set hours and minutes
6| Press D+| DEFAULT IS EVERY DAY OF
THE WEEK or you can select one of the following options by pressing
the D+ button
OPTIONS: MO-FR,MO-SA,SA SU,MO-WE,TH-SA,MO WE FR,TU TH SA
7| Repeat steps 4-9| Set 2-18 ON PULSE programs
(OFF programs not required!)
8| Press ¹| End (“P” will continue to flash when PULSE program
is set)
9| Press and HOLD H+ and M+| Exit PULSE
function
Countdown (“d” displays in bottom LHC)
This is a manual operation only initiated by pressing the “MANUAL” button on
the TD1
| Step | Key | Programming COUNTDOWN function |
|---|---|---|
| 1 | Press and HOLD P and ¹ | Enter COUNTDOWN setting |
(“d” displays in bottom LHC)
2| Press ¹ and H+ or M+| Set COUNTDOWN time range:
1sec to 99min 59sec
3| Press MANUAL| Start COUNTDOWN
4| Press P| Return to start of COUNTDOWN
5| Press and HOLD P and ¹| End COUNTDOWN
(“d” no longer displayed in bottom LHC)
PAUSE program settings
| Step | Key | Programming PAUSE function |
|---|---|---|
| 1 | Press ¹ and MANUAL for 3s | Permanent “AUTO OFF” |
state(“┌” flashes in bottom LHC)
2| Press ¹ and MANUAL for 3s| To restore “AUTO”
settings
PAUSE function can only be accessed when “AUTO ON” or “AUTO OFF” is displayed
on the LCD
Auto time correction (“7d” displayed at left hand side of LCD)
| Step | Key | Programming ON memory location |
|---|---|---|
| 1 | Press P and MANUAL | Into count |
| 2 | Press D+ | Setting -30s to +30s |
| 3 | Press ¹ | Confirm |
Testing
- On completion of the installation, it must be tested in accordance with the latest edition of the IET Wiring Regulations for Electrical Installations (BS 7671).
Environment
WASTE ELECTRICAL PRODUCTS SHOULD NOT BE DISPOSED OF IN HOUSEHOLD WASTE.
CONTACT YOUR RETAILER OR LOCAL AUTHORITY FOR RECYCLING INFORMATION.
Fuse Box
www.fusebox.co.uk
After installation and testing of this product it is essential that the INSTRUCTION LEAFLET is available for reference
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>