PHILIPS BVP130 Coreline Tempo Large User Manual
- June 8, 2024
- Philips
Table of Contents
PHILIPS BVP130 Coreline Tempo Large
WHAT’S IN THE BOX
Features
|
Luminaire Flux (lm)
|
Power (W)
|
CCT
|
CRI
|
Beam
|
| |
---|---|---|---|---|---|---|---|---
| | | | | | | |
BVP130 LED260-4S/740| 26000| 217| | | | | |
| | | | | | | | 7.5
BVP130 LED210-4S/740| 21000| 162| 4000| 70| | |
BVP130 LED160-4S/740| 16000| 120| | | 7.0
| | | | | S/OFA52| 0.15| |
BVP130 LED216-4S/830| 21600| 223| | | | |
| | | | | | | 7.5
BVP130 LED172-4S/830| 17220| 165| 3000| 80| | |
BVP130 LED131-4S/830| 13120| 126| | | | | 7.0
.
| LED260|
---|---|---
| LED210| LED160
Electrical characteristics
Imax (A)| 53| 53
Tref (µs)| 300| 300
Surge protection(kv)| 6| 6
MCB| Downlights Max.
B-10 A| 2| 4
B-16 A| 4| 8
B-10 A| 4| 8
C-16 A| 6| 13
- InstaIl the luminaire according to the national regulations.
- In the case of using only the central hole xation and if the luminaire is higher > m, the use of the 2nd xing security system is mandatory.
| Connector position | PSU connector 3 poles | DALI connector 5 poles |
|---|---|---|
| 1 | – | N (blue) |
| 2 | L (brown) | DALI+ (black) |
| 3 | N (blue) | DALI- (grey) |
| 4 | ground (yellow/green) | L (brown) |
| 5 | – | ground (yellow/green) |
No connector (L brown, N blue, GRD yellow/green, DALI- grey and DALI+ black)
glass maintenance instruction
The luminaire power should be switched off before opening.
- The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualied person.
- The luminaire shall be installed or maintained by a qualied electrician and wired in accordance with the latest
- IEE electrical regulations or the national requirements.
- lf the external exible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualied person in order to avoid a hazard.
- Outdoor use only.
For products with TAG Label
-
Disconnect before servicing
-
Luminaire has basic insulation between Low Voltage supply and control conductors.
-
The light source and/or control gear and/or the external flexible cable contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
-
Storage, installation, use, operation and maintenance of the products needs to be performed exactly according the instructions in this manual and/or other instructions as may be provided by us to guarantee safe use of the product over its entire lifetime. Failure to adhere to these instructions will invalidate your entitlement to warranty. Bolts with indication of torque strength on the drawing need to be tightened using a calibrated torque wrench. Pre-assembled bolts need to be retightened again to the required torque specification to assure maximum strength over lifetime.
-
This product contains a light source of energy efficiency class: see table or label.
-
© 2020 Signify Holding.
-
All rights reserved. This document contains information relating to the product portfolio of Signify which information may be subject to change.
-
No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. The
information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract. -
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V.. All other trademarks are owned by Signify Holding or their respective owners.
-
Signify Holding.
-
The Netherlands